journal article·2017-12

Effects of Heating and Cooling Rates on Phase Transformations in 10 Wt Pct Ni Steel and Their Application to Gas Tungsten Arc Welding

Erin J. Barrick, Divya Jain, John N. DuPont, David N. Seidman

Publisher page

Abstract

10 wt pct Ni steel is a high-strength steel that possesses good ballistic resistance from the deformation induced transformation of austenite to martensite, known as the transformation-induced-plasticity effect. The effects of rapid heating and cooling rates associated with welding thermal cycles on the phase transformations and microstructures, specifically in the heat-affected zone, were determined using dilatometry, microhardness, and microstructural characterization. Heating rate experiments demonstrate that the Ac3 temperature is dependent on heating rate, varying from 1094 K (821 °C) at a heating rate of 1 °C/s to 1324 K (1051 °C) at a heating rate of 1830 °C/s. A continuous cooling transformation diagram produced for 10 wt pct Ni steel reveals that martensite will form over a wide range of cooling rates, which reflects a very high hardenability of this alloy. These results were applied to a single pass, autogenous, gas tungsten arc weld. The diffusion of nickel from regions of austenite to martensite during the welding thermal cycle manifests itself in a muddled, rod-like lath martensitic microstructure. The results of these studies show that the nickel enrichment of the austenite in 10 wt pct Ni steel plays a critical role in phase transformations during welding.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Hydrogen embrittlement and corrosion behaviors in metals · Advanced Materials Characterization Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (53)

Show source-provided references
1. X.J. Zhang: Mater. Sci. Technol., 2012, vol. 28, pp. 818–22.10.1179/1743284712Y.0000000015 ↗
2. D. Isheim, A.H. Hunter, X.J. Zhang, and D.N. Seidman: Metall. Mater. Trans. A, 2013, vol. 44A, pp. 3046–59.10.1007/s11661-013-1670-6 ↗
3. V.F. Zackay, V.F. Parker, E.R. Fahr, and R. Busch: Trans. Am. Soc. Met., 1967, vol. 60, pp. 252–59.
4. H.K.D.H. Bhadeshia and R.W.K. Honeycombe: Steels: Microstructure and Properties, 3rd ed., Butterworth-Heinemann, Oxford, 2006, pp. 71–73, 223–26, 298–306.
5. W.W. Gerberich, G. Thomas, E.R. Parker, and V.F. Zackay: Proc. 2nd Int. Conf. Strength Met. Alloys, August 30–September 4, 1970, American Society for Metals, Materials Park, OH, 1970, pp. 894–99.
6. J.I. Kim, C.K. Syn, and J.W. Morris: Metall. Trans. A, 1983, vol. 14A, pp. 93–103.10.1007/BF02643742 ↗
7. W.Y. Choo, S.W. Lee, and J.Y. Yoo: 38th Mech. Work. Steel Process. Conf. Proc., vol. XXXIV, Cleveland, Ohio, October 13–16, 1996, Iron and Steel Society, Warrendale, PA, 1997, pp. 483–91.
8. J. Jang, Y. Yang, W. Kim, and D. Kwon: Advances in Cryogenic Engineering Materials, Springer, New York, 1998, vol. 44, pp. 41–48.10.1007/978-1-4757-9056-6_6 ↗
9. J.I. Jang, B.W. Lee, J.B. Ju, D. Kwon, and W.S. Kim: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 2615–22.10.1007/s11661-002-0383-z ↗
10. J.I. Jang, J.B. Ju, B.W. Lee, D. Kwon, and W.S. Kim: Mater. Sci. Eng. A, 2003, vol. 340A, pp. 68–79.10.1016/S0921-5093(02)00190-9 ↗
11. X.Q. Zhao, T. Pan, Q.F. Wang, H. Su, C.F. Yang, Q.X. Yang, and Y.Q. Zhang: J. Iron Steel Res. Int., 2007, vol. 14, pp. 240–44.10.1016/S1006-706X(08)60086-2 ↗
12. S.J. Wu, G.J. Sun, Q.S. Ma, Q.Y. Shen, and L. Xu: J. Mater. Process. Technol., 2013, vol. 213, pp. 120–28.10.1016/j.jmatprotec.2012.08.005 ↗
13. Y. Yang, Q. Cai, D. Tang, and H. Wu: Int. J. Miner. Metall. Mater., 2010, vol. 14, pp. 587–95.10.1007/s12613-010-0361-1 ↗
14. 1J.I. Jang, J.S. Lee, J.B. Ju, B.W. Lee, D. Kwon, and W.S. Kim: Mater. Sci. Eng. A, 2003, vol. 351A, pp. 183–89.10.1016/S0921-5093(02)00850-X ↗
15. D. Jain, D. Isheim, X.J. Zhang, G. Ghosh, and D.N. Seidman: Metall. Mater. Trans. A, 2017, vol. 48A, pp. 3642–54.10.1007/s11661-017-4146-2 ↗
16. B.L. Averbach and M. Cohen: Trans. AIME, 1948, vol. 179, pp. 401–15.
17. G.E. Hicho, H. Yakowitz, and R.E. Michaelis: Adv. X-ray Anal., 1971, vol. 14, p. 78.
18. P.W. Fuerschbach and G.R. Eisler: Trends Weld. Res.: Proc. 6th Int. Conf., Phoenix, AZ, USA, April 15–19, 2002, ASM International, Materials Park, OH, 2002, pp. 782–86.
19. G.R. Eisler and P.W. Fuerschbach: Seventh Int. Conf. Comput. Technol. Weld., San Francisco, CA, July 8–11, 1997, National Institute of Standards and Technology, Washington, DC, 1997, pp. 257–68.
20. J.O. Andersson, T. Helander, L. Höglund, P.F. Shi, and B. Sundman: Calphad, 2002, vol. 26, pp. 273–312.10.1016/S0364-5916(02)00037-8 ↗
21. Thermo-Calc Software TCFE8 Steels/Fe-Alloys Database Version 8, Thermo-Calc Software, Stockholm, 2015.
22. M.K. Miller, K.F. Russell, and G.B. Thompson: Ultramicroscopy, 2005, vol. 102, pp. 287–98.10.1016/j.ultramic.2004.10.011 ↗
23. R.W. Fonda and G. Spanos: Metall. Mater. Trans. A, 2014, vol. 45A, pp. 5982–89.10.1007/s11661-014-2588-3 ↗
24. R.W. Fonda, G. Spanos, and R.A. Vandermeer: Scripta Metall. Mater., 1994, vol. 31, pp. 683–88.10.1016/0956-716X(94)90210-0 ↗
25. G. Spanos, R.W. Fonda, R.A. Vandermeer, and A. Matuszeski: Metall. Mater. Trans. A, 1995, vol. 26A, pp. 3277–93.10.1007/BF02669455 ↗
26. H. Pous-Romero and H.K.D.H. Bhadeshia: J. Press. Vessel Technol., 2014, vol. 136, pp. 031402.10.1115/1.4026192 ↗
27. J.H. Pak, H.K.D.H. Bhadeshia, and L. Karlsson: Mater. Sci. Technol., 2012, vol. 28, pp. 918–23.10.1179/1743284712Y.0000000023 ↗
28. J.H. Pak, D.W. Suh, and H.K.D.H. Bhadeshia: Scripta Mater., 2012, vol. 66, pp. 951–53.10.1016/j.scriptamat.2012.02.041 ↗
29. H.K.D.H. Bhadeshia, E. Keehan, L. Karlsson, and H.O. Andrén: Trans. Indian Inst. Met., 2006, vol. 59, pp. 689–94.
30. J.H. Pak, H.K.D.H. Bhadeshia, L. Karlsson, and E. Keehan: Sci. Technol. Weld. Join., 2008, vol. 13, pp. 593–97.10.1179/136217108X338926 ↗
31. E. Keehan, L. Karlsson, and H.O. Andrén: Sci. Technol. Weld. Join., 2006, vol. 11, pp. 1–8.10.1179/174329306X77830 ↗
32. D.N. Seidman: Annu. Rev. Mater. Res., 2007, vol. 37, pp. 127–58.10.1146/annurev.matsci.37.052506.084200 ↗
33. D.N. Seidman and K. Stiller: Mater. Res. Soc. Bull., 2009, vol. 34, pp. 717–21.10.1557/mrs2009.194 ↗
34. O.C. Hellman and D.N. Seidman: Mater. Sci. Eng., 2002, vol. 327, pp. 24–8.10.1016/S0921-5093(01)01885-8 ↗
35. O.C. Hellman, J. Vandenbroucke, J. Blatz du Rivage, and D.N. Seidman: Mater. Sci. Eng., 2002, vol. 327, pp. 29–33.10.1016/S0921-5093(01)01887-1 ↗
36. D. Isheim, O.C. Hellman, J. Rüsing, and D.N. Seidman: Interface Sci., 2002, vol. 9, pp. 257–64.10.1023/A:1015110912262 ↗
37. J. Rüsing, J.T. Sebastian, O.C. Hellman, and D.N. Seidman: Microsc. Microanal., 2000, vol. 6, pp. 445–51.10.1007/S100050010050 ↗
38. O.C. Hellman, J.A. Vandenbroucke, J. Rüsing, D. Isheim, and D.N. Seidman: Microsc. Microanal., 2000, vol. 6, pp. 437–44.10.1007/S100050010051 ↗
39. G. Krauss: Steels: Processing, Structure, and Performance, 2nd ed., ASM International, Materials Park, OH, 2015, pp. 30–31, 63–73, 338–40.
40. R. Wei, M. Enomoto, R. Hadian, H.S. Zurob, and G.R. Purdy: Acta Mater., 2013, vol. 61, pp. 697–707.10.1016/j.actamat.2012.10.019 ↗
41. S. Watanabe, Y. Ohmori, and T. Kunitake: Proc. 1st Int. Conf. N. Asp. Martensitic Transform., Kobe, JP, May 10–12, 1976, The Japan Institute of Metals, Sendai, JP, 1976, pp. 369–74.
42. B. Fultz, J.I. Kim, Y.H. Kim, and J.W. Morris: Metall. Trans. A, 1986, vol. 17A, pp. 967–72.10.1007/BF02661262 ↗
43. B. Fultz, J.I. Kim, Y.H. Kim, H.J. Kim, G.O. Fior, and J.W. Morris: Metall. Trans. A, 1985, vol. 16A, pp. 2237–49.10.1007/BF02670423 ↗
44. C.A. Apple and G. Krauss: Acta Metall., 1972, vol. 20, pp. 849–56.10.1016/0001-6160(72)90077-6 ↗
45. H. Kessler and W. Pitsch: Acta Metall., 1967, vol. 15, pp. 401–05.10.1016/0001-6160(67)90224-6 ↗
46. Y.K. Lee, H.C. Shin, D.S. Leem, J.Y. Choi, W. Jin, and C.S. Choi: Mater. Sci. Technol., 2003, vol. 19, pp. 393–98.10.1179/026708303225009742 ↗
47. H. Oikawa: Technol. Rep. Tohoku Univ., 1982, vol. 47, pp. 215–24.
48. D.A. Porter, K.E. Easterling, and M.Y. Sherif: Phase Transformations in Metals and Alloys, 3rd ed., Taylor and Francis Group, Boca Raton, FL, 2009, pp. 65–98.
49. K.W. Andrews: J. Iron Steel Inst., 1965, vol. 203, pp. 721–27.
50. W. Steven and A.G. Haynes: J. Iron Steel Inst., 1956, vol. 183, pp. 349–59.
51. S. Kou: Welding Metallurgy, 2nd ed., Wiley, Hoboken, NJ, 2003, pp. 393–410.
52. E.F. Nippes and J.P. Balaguer: Weld. J., 1986, vol. 65, pp. 237s–43s.
53. X.J. Zhang: NSWCCD, Bethesda, MD, unpublished research, 2016.