Effect of Strain Rate on the Formation of Strain-Induced Martensite in AISI 304L Stainless Steel
Source abstract
Abstract
The effect of strain rate on the stress–strain response and the austenite to strain-induced α′-martensite transformation of austenitic steel 304L was studied. Compression tests were carried out at room temperature in the strain rate range of 10−3 to 103 s−1 and the evolution of martensite was quantified using a ferritoscope. Higher strain rates resulted in lower strain-induced α′-martensite. Strain incremental tests were carried out at 1 s−1 to simulate isothermal tests and to delineate effect of adiabatic heating on the α′-martensite transformation. Strain rate change tests were also carried out to determine the effect of prior strain rate history on the strain-induced α′-martensite content. These experiments showed that apart from the effect of adiabatic heating at high strain rates on the α′-martensite content, there is an additional effect of strain rate. While the adiabatic heating effect could be based on the increase in stacking fault energy (reduction of stacking fault width) with temperature, the additional effect due to strain rate was explained based on the expected reduction in stacking fault width with increasing strain rate.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Hydrogen embrittlement and corrosion behaviors in metals
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (29)
Show source-provided references
1. T. Angel: Journal of Iron and Steel Institute, 1954, vol. 177, pp. 165-174.
2. G.H. Eichelmann, F.C. Hull: Trans. ASM, 1953, vol. 45, pp. 45.
3. G.B. Olson, M. Cohen: Metallurgical Transactions A, 1975, vol. 6, pp. 791.10.1007/BF02672301 ↗
4. J.R. Patel, M. Cohen: Acta Metallurgica, 1953, vol. 1, pp. 531-538.10.1016/0001-6160(53)90083-2 ↗
5. R. Lagneborgj: Acta Metallurgica, 1964, vol. 12, pp. 823-843.10.1016/0001-6160(64)90176-2 ↗
6. P.L. Mangonon, G. Thomas: Metallurgical Transactions, 1970, vol. 1, pp. 1577-1586.10.1007/BF02642003 ↗
7. J.A. Venables: Philosophical Magazine, 1962, vol. 7, pp. 35-44.10.1080/14786436208201856 ↗
8. S.S. Hecker, M.G. Stout, K.P. Staudhammer, J.L. Smith: Metallurgical Transactions A, 1982, vol. 13, pp. 619-626.10.1007/BF02644427 ↗
9. G.L. Huang, D.K. Matlock, G. Krauss: Metallurgical Transactions A, 1989, vol. 20, pp. 1239-1246.10.1007/BF02647406 ↗
10. M. Isakov, S. Hiermaier, V.-T. Kuokkala: Metallurgical and Materials Transactions A, 2015, vol. 46, pp. 2352-2355.10.1007/s11661-015-2862-z ↗
11. J.A. Lichtenfeld, C.J. Van Tyne, M.C. Mataya: Metallurgical and Materials Transactions A, 2006, vol. 37, pp. 147-161.10.1007/s11661-006-0160-5 ↗
12. L.E. Murr, K.P. Staudhammer, S.S. Hecker: Metallurgical Transactions A, 1982, vol. 13, pp. 627-635.10.1007/BF02644428 ↗
13. J. Talonen, H. Hänninen, P. Nenonen, G. Pape: Metallurgical and Materials Transactions A, 2005, vol. 36, pp. 421-432.10.1007/s11661-005-0313-y ↗
14. W.-S. Lee, C.-F. Lin: Materials Science and Engineering A, 2001, vol. 308, pp. 124-135.10.1016/S0921-5093(00)02024-4 ↗
15. N. Vázquez-Fernández, T. Nyyssönen, M. Isakov, M. Hokka, V.-T. Kuokkala: Acta Materialia, 2019, vol. 176, pp. 134-144.10.1016/j.actamat.2019.06.053 ↗
16. S. Nemat-Nasser: ASM International, West Conshohocken, 1985, PA, p. 190.
17. S. Sharma, R. Kapoor, V.M. Chavan, R.G. Agrawal, R.J. Patel, and J.K. Chakravartty: BARC External Report, 2011, BARC/2011/E/013.
18. J. Talonen, P. Aspegren, H. Hänninen: Materials Science and Technology, 2004, vol. 20, pp. 1506-1512.10.1179/026708304X4367 ↗
19. Y.F. Shen, X.X. Li, X. Sun, Y.D. Wang, L. Zuo: Materials Science and Engineering A, 2012, vol. 552, pp. 514-522.10.1016/j.msea.2012.05.080 ↗
20. G. Olson, M. Cohen: Journal of the Less Common Metals, 1972, vol. 28, pp. 107-118.10.1016/0022-5088(72)90173-7 ↗
21. L. Rémy, A. Pineau, B. Thomas: Materials Science and Engineering, 1978, vol. 36, pp. 47-63.10.1016/0025-5416(78)90194-5 ↗
22. J. Talonen, H. Hänninen: Acta Materialia, 2007, vol. 55, pp. 6108-6118.10.1016/j.actamat.2007.07.015 ↗
23. D. Hull and D.J. Bacon: Introduction to Dislocations, Elsevier Science & Technology Books, Amsterdam, 1984.
24. Y.N. Petrov: Zeitschrift für Metallkunde, 2003, vol. 94, pp. 1012-1016.10.3139/146.031012 ↗
25. D. Kaoumi, J. Liu: Materials Science and Engineering A, 2018, vol. 715, pp. 73-82.10.1016/j.msea.2017.12.036 ↗
26. A. Miodownik: Calphad, 1978, vol. 2, pp. 207-226.10.1016/0364-5916(78)90010-X ↗
27. E.I. Galindo-Nava, P. Rivera-Díaz-del-Castillo: Acta Materialia, 2017, vol. 128, pp. 120-134.10.1016/j.actamat.2017.02.004 ↗
28. G. Taylor: Progress in Materials Science, 1992, vol. 36, pp. 29-61.10.1016/0079-6425(92)90004-Q ↗
29. U.F. Kocks, A.S. Argon and M.F. Ashby: Progress in Materials Science, 1975, vol. 19, pp. 1-291.10.1016/0079-6425(75)90005-5 ↗