journal article·2017-11Open access

Retained Austenite Transformation during Heat Treatment of a 5 Wt Pct Cr Cold Work Tool Steel

M. Arbab Rehan, Anna Medvedeva, Lars-Erik Svensson, Leif Karlsson

Abstract

Abstract Retained austenite transformation was studied for a 5 wt pct Cr cold work tool steel tempered at 798 K and 873 K (525 °C and 600 °C) followed by cooling to room temperature. Tempering cycles with variations in holding times were conducted to observe the mechanisms involved. Phase transformations were studied with dilatometry, and the resulting microstructures were characterized with X-ray diffraction and scanning electron microscopy. Tempering treatments at 798 K (525 °C) resulted in retained austenite transformation to martensite on cooling. The martensite start (M s ) and martensite finish (M f ) temperatures increased with longer holding times at tempering temperature. At the same time, the lattice parameter of retained austenite decreased. Calculations from the M s temperatures and lattice parameters suggested that there was a decrease in carbon content of retained austenite as a result of precipitation of carbides prior to transformation. This was in agreement with the resulting microstructure and the contraction of the specimen during tempering, as observed by dilatometry. Tempering at 873 K (600 °C) resulted in precipitation of carbides in retained austenite followed by transformation to ferrite and carbides. This was further supported by the initial contraction and later expansion of the dilatometry specimen, the resulting microstructure, and the absence of any phase transformation on cooling from the tempering treatment. It was concluded that there are two mechanisms of retained austenite transformation occurring depending on tempering temperature and time. This was found useful in understanding the standard tempering treatment, and suggestions regarding alternative tempering treatments are discussed.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Metallurgy and Material Forming

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (29)

Show source-provided references
1. G. Roberts, G. Kraus, and R. Kennedy: Tool Steels, 5th ed., ASM International, Materials Park, Metals Park, 2000, 79–103.
2. Uddeholm Steel for Cold Work Tooling, 9th ed., 2014, http://www.uddeholm.com/files/AB_cold_work_eng.pdf, accessed 11 02 2016.
3. G.R. Speich and W.C. Leslie: Metall. Trans.,1972, vol. 3, pp. 1043–54.10.1007/BF02642436 ↗
4. H.K.D.H. Bhadeshia: Bainite in Steels, 2nd ed., IOM Commercial Ltd., London, 2001, pp. 307–10.
5. H.K.D.H. Bhadeshia and R.W.K. Honeycombe: Steels: Microstructure and Properties, 3rd ed., Elsevier Ltd., Oxford, United Kingdom, 2006, pp. 183–207.10.1016/B978-075068084-4/50011-X ↗
6. A.S. Podder and H.K.D.H. Bhadeshia: Mater. Sci. Eng. A, 2010, vol. 527, pp. 2121–28.10.1016/j.msea.2009.11.063 ↗
7. M.J. Van Genderen, M. Isac, A. Böttger, and E.J. Mittemeijer: Metall. Mater. Trans. A, 1997, vol. 28A, pp. 545–61.10.1007/s11661-997-0042-5 ↗
8. S. Primig and H. Leitner: Thermochim. Acta, 2011, vol. 526, pp. 111–17.10.1016/j.tca.2011.09.001 ↗
9. P.V. Morra, A.J. Bötter, and E.J. Mittemeijer: J. Therm. Anal. Calorim., 2001, vol. 64, pp. 905–14.10.1023/A:1011514727891 ↗
10. C. Lerchbacher, S. Zinner, and H. Leitner: Mater. Sci. Eng. A, 2013, vol. 564, pp. 163–68.10.1016/j.msea.2012.11.105 ↗
11. C. Lerchbacher, S. Zinner, and H. Leitner: Micron, 2012, vol. 43, pp. 818–26.10.1016/j.micron.2012.02.005 ↗
12. M. Sarikaya, A.K. Jhingan, and G. Thomas: Metall. Trans. A, 1983, vol. 14A, pp. 1121–33.10.1007/BF02659860 ↗
13. M.J. Dickson: J. Appl. Crystallogr., 1969, vol. 2, pp. 176–80.10.1107/S0021889869006881 ↗
14. B.D. Cullity: Elements of X-ray Diffraction, 2nd ed., Addison-Wesley, Reading, 1978, p. 411.
15. C. Suryanarayana and M.G. Norton: X-Ray Diffraction, A Practical Approach, Plenum Publishing Corp., New York, NY, 1998, p. 101.10.1007/978-1-4899-0148-4 ↗
16. C. Garcia-Mateo, M. Preet, F.G. Caballero, and H.K.D.H. Bhadeshia: Mater. Sci. Technol., 2004, vol. 20, pp. 814–18.10.1179/026708304225017355 ↗
17. Standard practice for quantitative measurement and reporting of hypoeutectoid carbon and low-alloy steel phase transformations. ASTM International, 2010, https://compass.astm.org Accessed 08 July 2016.
18. M.A. Rehan, A. Medvedeva, B. Högman, L.E. Svensson, and L. Karlsson: Steel Res. Int., 2016, vol. 87, pp. 1609–18.10.1002/srin.201600012 ↗
19. G.F. Van der Voort: Metallography Principles and Practice, ASM International, Materials Park, OH, 1999, pp. 166–67.
20. J. Akre, F. Danoix, H. Leitner, and P. Auger: Ultramicroscopy, 2009, vol. 109, pp. 518–23.10.1016/j.ultramic.2008.11.010 ↗
21. K. Stiller, L.E. Svensson, P.R. Howell, W. Rong, H.O. Andren, and G.L. Dunlop: Acta Metall., 1984, vol. 32, pp. 1457–67.10.1016/0001-6160(84)90092-0 ↗
22. M. WieBner, S. Kleber, and A. Kulmburg: Particle Particle Syst. Charact., 2005, vol. 22, pp. 407–17.10.1002/ppsc.200501002 ↗
23. K.W. Andrews: J. Iron Steel Inst., 1965, vol. 203, pp. 721–27.
24. D.J. Dyson and B. Holmes: J. Iron Steel Inst., 1970, vol. 208, pp. 469–74.
25. N. Ridley, H. Stuart, and L. Zwell: Trans. TMS-AIME, 1969, vol. 245, pp. 1834–36.
26. F.G. Caballero, C. Capdevila, and C.G.D Andres: ISIJ Int., 2001, vol. 41, pp. 1093–1102.10.2355/isijinternational.41.1093 ↗
27. P.M. Yushkevich: Metalloved. Obrab. Met., 1960, vol. 2, pp. 14–20.
28. L.I. Kogan and R.I. Entin: Fiz. Met. Metalloved., 1968, vol. 25, pp. 383–84.
29. V.A. Landa: Metalloved. Term. Obrab. Met., 1963, vol. 3, pp. 2–6.