High Strain Rate Compression of Martensitic NiTi Shape Memory Alloy at Different Temperatures
Source abstract
Abstract
The compressive response of martensitic NiTi shape memory alloy (SMA) rods has been investigated using a modified Kolsky compression bar at various strain rates (400, 800, and 1200 s−1) and temperatures [room temperature and 373 K (100 °C)], i.e., in the martensitic state and in the austenitic state. SEM, DSC, and XRD were performed on NiTi SMA rod samples after high strain rate compression in order to reveal the influence of strain rate and temperature on the microstructural evolution, phase transformation, and crystal structure. It is found that at room temperature, the critical stress increases slightly as strain rate increases, whereas the strain-hardening rate decreases. However, the critical stress under high strain rate compression at 373 K (100 °C) increase first and then decrease due to competing strain hardening and thermal softening effects. After high rate compression, the microstructure of both martensitic and austenitic NiTi SMAs changes as a function of increasing strain rate, while the phase transformation after deformation is independent of the strain rate at room temperature and 373 K (100 °C). The preferred crystal plane of the martensitic NiTi SMA changes from ( $$ 1\bar{1}1 $$ )M before compression to (111)M after compression, while the preferred plane remains the same for austenitic NiTi SMA before and after compression. Additionally, dynamic recovery and recrystallization are also observed to occur after deformation of the austenitic NiTi SMA at 373 K (100 °C). The findings presented here extend the basic understanding of the deformation behavior of NiTi SMAs and its relation to microstructure, phase transformation, and crystal structure, especially at high strain rates.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Shape Memory Alloy Transformations · Titanium Alloys Microstructure and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (60)
Show source-provided references
1. D.J. Hartl and D.C. Lagoudas: Proc. Inst. Mech. Eng. Part G J. Aerosp. Eng., 2007, vol. 221, pp. 535–52.10.1243/09544100JAERO211 ↗
2. A.. Fallis: J. Chem. Inf. Model., 2013, vol. 53, pp. 1689–99.10.1021/ci400128m ↗
3. D. Stoeckel: Mater. Des., 1991, vol. 11, pp. 302–7.10.1016/0261-3069(90)90013-A ↗
4. Y. Furuya and H. Shimada: Mater. Des., 1991, vol. 12, pp. 21–28.10.1016/0261-3069(91)90088-L ↗
5. D. Mantovani: Jom, 2000, vol. 52, pp. 36–44.10.1007/s11837-000-0082-4 ↗
6. M. Bahraminasab and B. Bin Sahari: in Shape Mem. Alloy. Process. Charact. Appl., 2013, pp. 261–78.
7. O. Benafan, J. Brown, F.T. Calkins, P. Kumar, A. P. Stebner, T.L. Turner, R. Vaidyanathan, J. Webster, and M.L. Young: Int. J. Mech. Mater. Des., 2014, 10: 1–42.10.1007/s10999-013-9227-9 ↗
8. D.J. Hartl, J.T. Mooney, D.C. Lagoudas, F.T. Calkins, and J.H. Mabe: Smart Mater. Struct., 2009, vol. 19, p. 015021.10.1088/0964-1726/19/1/015021 ↗
9. T. Duerig: MRS Proc., 1994, vol. 360, pp. 497–506.10.1557/PROC-360-497 ↗
10. T. Duerig, A. Pelton, and D. Stöeckel: Mater. Sci. Eng. A, 1999, vol. 273-275, pp. 149–60.10.1016/S0921-5093(99)00294-4 ↗
11. R. Zarnetta and R. Takahashi: Adv. Funct. Mater., 2010, vol. 20, pp. 1917–23.10.1002/adfm.200902336 ↗
12. S. Gollerthan, M. Young, and A. Baruj: Acta Mater., 2009, vol. 57, pp. 1015–25.10.1016/j.actamat.2008.10.055 ↗
13. Y.A. Chang, J.P. Neumann, A. Mikula, and D. Goldberg: Bull. Alloy Phase Diagrams, 1980, vol. 1, pp. 82–84.10.1007/BF02883303 ↗
14. S. Saadat, J. Salichs, M. Noori, Z. Hou, H. Davoodi, I. Bar-on, Y. Suzuki, and A. Masuda: Smart Mater. Struct., 2002, vol. 11, pp. 218–29.10.1088/0964-1726/11/2/305 ↗
15. T. Duerig, in Proc. SPIE, 2003, pp. 7–15.10.1117/12.508666 ↗
16. M.M. Kheirikhah, S. Rabiee, M.E. Edalat, RoboCup 2010 Robot Soccer World Cup XIV, LNAI, vol. 6556 (Springer, Berlin, 2011), pp. 206–17.10.1007/978-3-642-20217-9_18 ↗
17. K. Otsuka and X. Ren: Intermetallics, 1999, vol. 7, pp. 511–28.10.1016/S0966-9795(98)00070-3 ↗
18. S. Jiang and Y. Zhang: Trans. Nonferrous Met. Soc. China, 2012, vol. 22, pp. 90–96.10.1016/S1003-6326(11)61145-X ↗
19. Y. Liu, Z. Xie, in Prog. Smart Mater. Struct., 2007, pp. 29–65.
20. T. Sakuma, Y. Mihara, H. Toyama, Y. Ochi, and K. Yamauchi: Mater. Trans., 2006, vol. 47, pp. 787–91.10.2320/matertrans.47.787 ↗
21. P. Sittner, Y. Liu, and V. Novak: J. Mech. Phys. Solids, 2005, vol. 53, pp. 1719–46.10.1016/j.jmps.2005.03.005 ↗
22. Y. Liu and H. Xiang: J. Alloys Compd., 1998, vol. 270, pp. 154–59.10.1016/S0925-8388(98)00500-3 ↗
23. Y. Liu, J. Van Humbeeck, R. Stalmans, and L. Delaey: J. Alloys Compd., 1997, vol. 247, pp. 115–21.10.1016/S0925-8388(96)02572-8 ↗
24. A.P. Stebner, H.M. Paranjape, B. Clausen, L.C. Brinson, A.R. Pelton, Shape Mem. Superelasticity, 2015.
25. J. Pilch, C. Curfs, and P. Sedma: 2015, vol. 94, pp. 257–70.10.1016/j.actamat.2015.04.039 ↗
26. Y. Liu: Acta Mater., 2015, vol. 95, pp. 411–27.10.1016/j.actamat.2015.03.022 ↗
27. T. Ezaz, J. Wang, H. Sehitoglu, and H.J. Maier: Acta Mater., 2013, vol. 61, pp. 67–78.10.1016/j.actamat.2012.09.023 ↗
28. B.J. Mentz, M. Bram, H.P. Buchkremer, D. Stöver, Y.A. Chang, S. Chen, F. Zhang, F. Xie, R. Schmid-fetzer, and W.A. Oates: Adv. Eng. Mater., 2006, vol. 459, pp. 247–52.10.1002/adem.200500258 ↗
29. K. Ogawa: J. Phys. IV, 1988, vol. 49, pp. c3–115.
30. Y. Liu, Y. Li, K.. Ramesh, and J. Van Humbeeck: Scr. Mater., 1999, vol. 41, pp. 89–95.10.1016/S1359-6462(99)00058-5 ↗
31. R.R. Adharapurapu, F. Jiang, K.S. Vecchio, and G.T. Gray: Acta Mater., 2006, vol. 54, pp. 4609–20.10.1016/j.actamat.2006.05.047 ↗
32. H. Nakayama, Y. Zhao, M. Taya, W.W. Chen, Y. Urushiyama, S. Suzuki, Smart Struct. Mater. 2005 - Acta Mater. Behav. Mech. March 7, 2005–March 10, 2005, 2005, vol. 5761, pp. 355–63.
33. S. Nemat-Nasser, J.Y. Choi, W.G. Guo, and J.B. Isaacs: Mech. Mater., 2005, vol. 37, pp. 287–98.10.1016/j.mechmat.2004.03.007 ↗
34. K.A. H. Fujimoto, M. Isomura, Biosci. Biotechnol. Biochem., n.d.
35. S. Nemat-Nasser and W.G. Guo: Mech. Mater., 2006, vol. 38, pp. 463–74.10.1016/j.mechmat.2005.07.004 ↗
36. W. Chen and B. Song: J. Mech. Mater. Struct., 2006, vol. 1, pp. 339–56.10.2140/jomms.2006.1.339 ↗
37. A. Bragov, A. Galieva, V. Grigorieva, A. Danilov, A. Konstantinov, A. Lomunov, A. Motorin, E. Ostropiko, and A. Razov: Mater. Sci. Forum, 2013, vol. 738-739, pp. 326–31.10.4028/www.scientific.net/MSF.738-739.326 ↗
38. S. Nemat-Nasser, J.Y. Choi, W.-G. Guo, J.B. Isaacs, and M. Taya: J. Eng. Mater. Technol., 2005, vol. 127, pp. 83–89.10.1115/1.1839215 ↗
39. H. Tobushi, Y. Shimeno, T. Hachisuka, and K. Tanaka: Mech. Mater., 1998, vol. 30, pp. 141–50.10.1016/S0167-6636(98)00041-6 ↗
40. W.W. Chen, Q. Wu, J.H. Kang, and N. A. Winfree: Int. J. Solids Struct., 2001, vol. 38, pp. 8989–98.10.1016/S0020-7683(01)00165-2 ↗
41. H. Tobushi, K. Takata, Y. Shimeno, W.K. Nowacki, S.P. Gadaj (1999) Mech. Eng. Part, 213: 93–102.
42. L. Brewer and R.H. Lamoreaux: Bull. Alloy Phase Diagrams, 1980, vol. 1, pp. 93–95.10.1007/BF02881201 ↗
43. M. D.A., T. W.R., M. D.A.S, J. Phys. IV Fr. 10, 341–46 (2000).
44. S.P. Belyaev, N.F. Morozov, A.I. Razov, A.E. Volkov, L.L. Wang, S.Q. Shi, S. Gan, J. Chen, and X.L. Dong: Mater. Sci. Forum, 2002, vol. 394-395, pp. 337–40.10.4028/www.scientific.net/MSF.394-395.337 ↗
45. R.R. Adharapurapu, F. Jiang, J.F. Bingert, and K.S. Vecchio: Mater. Sci. Eng. A, 2010, vol. 527, pp. 5255–67.10.1016/j.msea.2010.04.076 ↗
46. R.R. Adharapurapu, F. Jiang, and K.S. Vecchio: Mater. Sci. Eng. A, 2010, vol. 527, pp. 1665–76.10.1016/j.msea.2009.10.069 ↗
47. Y. Qiu, M.L. Young, and X. Nie: Metall. Mater. Trans. A, 2015, vol. 1, pp. 310–18.
48. Y. Qiu, M.L. Young, and X. Nie: Shape Mem. Superelasticity, 2015, vol. 1, pp. 310–18.10.1007/s40830-015-0035-y ↗
49. L. Hu, S. Jiang, Y. Zhang, Y. Zhao, S. Liu, and C. Zhao: Intermetallics, 2016, vol. 70, pp. 45–52.10.1016/j.intermet.2015.12.003 ↗
50. O. Benafan, R.D. Noebe, S.A. Padula, A. Garg, B. Clausen, S. Vogel, and R. Vaidyanathan: Int. J. Plast., 2013, vol. 51, pp. 103–21.10.1016/j.ijplas.2013.06.003 ↗
51. S. Miyazaki, K. Otsuka, and Y. Suzuki: Scr. Metall., 1981, vol. 15, pp. 287–92.10.1016/0036-9748(81)90346-X ↗
52. S. Miyazaki and Y. Ohmi: J. Phys., 1982, vol. 43, pp. c4–255.
53. Y. Liu, Z. Xie, J. Van Humbeeck, and L. Delaey: Acta Mater., 1998, vol. 46, pp. 4325–38.10.1016/S1359-6454(98)00112-8 ↗
54. Y. Liu, Z. Xie, J. Van Humbeeck, and L. Delaey: Mater. Sci. Eng. A, 1999, vol. 273-275, pp. 679–84.10.1016/S0921-5093(99)00348-2 ↗
55. O. Benafan, S.A. Padula, R.D. Noebe, T.A. Sisneros, and R. Vaidyanathan: J. Appl. Phys., 2012, vol. 112, p. 093510.10.1063/1.4764313 ↗
56. S. Kobayashi: Rigaku J., 2010, vol. 26, pp. 3–11.
57. Z. Xie, Y. Liu, and J. Van Humbeeck: Acta Mater., 1998, vol. 46, pp. 1989–2000.10.1016/S1359-6454(97)00379-0 ↗
58. K. Otsuka and X. Ren: Prog. Mater. Sci., 2005, vol. 50, pp. 511–678.10.1016/j.pmatsci.2004.10.001 ↗
59. D. Treppmann, E. Hornbogen, Le J. Phys. IV (1997).
60. W. Johnson: Impact Strength of Materials, First Edit, Edward Arnold, Crane, Russak New York, 1972.