journal article·2009-12

Effect of Cyclic Thermal Process on Ultrafine Grain Formation in AISI 304L Austenitic Stainless Steel

B. Ravi Kumar, B. Mahato, Sailaja Sharma, J.K. Sahu

Publisher page

Abstract

As-received hot-rolled commercial grade AISI 304L austenitic stainless steel plates were solution treated at 1060 °C to achieve chemical homogeneity. Microstructural characterization of the solution-treated material revealed polygonal grains of about 85-μm size along with annealing twins. The solution-treated plates were heavily cold rolled to about 90 pct of reduction in thickness. Cold-rolled specimens were then subjected to thermal cycles at various temperatures between 750 °C and 925 °C. X-ray diffraction showed about 24.2 pct of strain-induced martensite formation due to cold rolling of austenitic stainless steel. Strain-induced martensite formed during cold rolling reverted to austenite by the cyclic thermal process. The microstructural study by transmission electron microscope of the material after the cyclic thermal process showed formation of nanostructure or ultrafine grain austenite. The tensile testing of the ultrafine-grained austenitic stainless steel showed a yield strength 4 to 6 times higher in comparison to its coarse-grained counterpart. However, it demonstrated very poor ductility due to inadequate strain hardenability. The poor strain hardenability was correlated with the formation of strain-induced martensite in this steel grade.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and mechanical properties · Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (36)

Show source-provided references
1. R.Z. Valiev: Mater. Sci. Eng. A, 1997, vol. 234A, pp. 59–66.10.1016/S0921-5093(97)00183-4 ↗
2. V.M. Segal: Mater. Sci. Eng. A, 1999, vol. 271, pp. 322–33.10.1016/S0921-5093(99)00248-8 ↗
3. Y. Fukuda, K. Oh-ishi, Z. Horita, and T.G. Langdon: Acta Mater., 2002, vol. 50, pp. 1359–68.10.1016/S1359-6454(01)00441-4 ↗
4. J. Kim, I. Kim, and D.H. Shin: Scripta Mater., 2001, vol. 45, pp. 421–26.10.1016/S1359-6462(01)01029-6 ↗
5. D.H. Shin, I. Kim, J. Kim, and K.T. Park: Acta Mater., 2001, vol. 49, pp. 1285–92.10.1016/S1359-6454(01)00010-6 ↗
6. Z. Horita, M. Furukawa, M. Nemoto, and T.G. Langdon: Mater. Sci. Technol., 2000, vol. 16, pp. 1239–45.10.1179/026708300101507091 ↗
7. Y.T. Zhu and T.C. Lowe: Mater. Sci. Eng. A, 2000, vol. 291, pp. 46–53.10.1016/S0921-5093(00)00978-3 ↗
8. Y. Saito, H. Utsunomiya, N. Tsuji, and T. Sakai: Acta Mater., 1999, vol. 47, pp. 579–83.10.1016/S1359-6454(98)00365-6 ↗
9. N. Tsuji, R. Ueji, and Y. Minamino: Scripta Mater., 2002, vol. 47, pp. 69–76.10.1016/S1359-6462(02)00088-X ↗
10. N. Tsuji, Y. Saito, H. Utsunomiya, and S. Tanigawa: Scripta Mater., 1999, vol. 40, pp. 795–800.10.1016/S1359-6462(99)00015-9 ↗
11. T. Inoue, S. Torizuka, and K. Nagai: Int. Symp. on Ultrafine Grained Steels (ISUGS 2001), The Iron and Steel Institute of Japan, Fukuoka, Japan, 2001, pp. 88–91.
12. K. Tomimura, S. Takaki, and Y. Tokunaga: ISIJ Int., 1991, vol. 31, pp. 1431–37.10.2355/isijinternational.31.1431 ↗
13. O. Kwon and Y.K. Lee: J. Kor. Inst. Met. Mater., 1994, vol. 32, pp. 958–66.
14. K. Tomimira, S. Takaki, S. Tanimoto, and Y. Tokunaga: ISIJ Int., 1991, vol. 31, pp. 721– 27.10.2355/isijinternational.31.721 ↗
15. S. Takaki, K. Tomimura, and S. Ueda: ISIJ Int., 1994. vol. 34, pp. 522–27.10.2355/isijinternational.34.522 ↗
16. D.L. Johannsen, A. Kyrolainen, and P.J. Ferreira: Metall. Mater. Trans. A, 2006, vol. 37, pp. 2325–38.10.1007/BF02586207 ↗
17. A. Di Schino, M. Barteri, and J.M. Kenny, Jr.: Mater. Sci. Lett., 2002, vol. 21, pp. 751–53.10.1023/A:1015757710546 ↗
18. S. Rajsekhara, P.J. Ferreira, L.P. Karjalainen, and A. Kyrolainen: Metall. Mater. Trans. A, 2007, vol. 38A, pp. 1202–10.10.1007/s11661-007-9143-4 ↗
19. A. Di Schino, M. Barteri, and J.M. Kenny, Jr.: Mater. Sci., 2002, vol. 21, pp. 4561–65.10.1023/A:1020631912685 ↗
20. C. Herrera, P.L. Plaut, and A.F. Padilha: Mater. Sci. Forum, 2007, vol. 550, pp. 423–28.10.4028/www.scientific.net/MSF.550.423 ↗
21. H. Mirzadeh and A. Najafizadeh: Mater. Charact., 2008, vol. 59, pp. 1650–54.10.1016/j.matchar.2008.03.004 ↗
22. M. Tokuzane, N. Matsumura, K. Tsuzaki, T. Maki, and I. Tamura: Metall. Trans. A, 1982, vol. 13A, pp. 1379–88.10.1007/BF02642875 ↗
23. S. Takaki, S. Tanimoto, and Y. Tokunaga: Trans. ISIJ, 1985, vol. 25, p. B223.
24. Y. Ma, J.-E., Jin, and Y.-K. Lee: Scripta Mater., 2005, vol. 52, pp. 1311–15.10.1016/j.scriptamat.2005.02.018 ↗
25. R.D.K. Misra, B. Ravi Kumar, M. Somani, and P. Karjalainen: Scripta Mater., 2008, vol. 59, pp. 79–82.10.1016/j.scriptamat.2008.02.028 ↗
26. D. Jia, Y.M. Wang, K.T.Y. Ramesh, E. Ma, Y.T. Zhu, and R.Z. Valiev: Appl. Phys. Lett., 2001, vol. 79, pp. 611–13.10.1063/1.1384000 ↗
27. Y.M. Wang and E. Ma: Mater. Sci. Eng. A, 2004, vols. 375–377, pp. 46–52.10.1016/j.msea.2003.10.214 ↗
28. K. Krishnan, S.S. Sahay, S. Singh, and D. Pal: J. Appl. Phys., 2006, vol. 100, pp. 93505-1–93505-5.10.1063/1.2363245 ↗
29. M. Gao, C.N. Reid, M. Jahedi, and Y. Li: J. Mater. Eng. Perform., 2000, vol. 9, pp. 62– 71.10.1361/105994900770346295 ↗
30. H. Mirzadeh and A. Najafizadeh: Mater. Design, 2009, vol. 30, pp. 570–73.10.1016/j.matdes.2008.05.057 ↗
31. H. Luo, J Sietsma, and S. Van Der Zwaag: Metall. Mater. Trans. A, 2004, vol. 35A, pp. 1889–98.10.1007/s11661-004-0097-5 ↗
32. E. Kozeschnik, V. Pletenev, N. Zolotorevsky, and B. Buchmayr: Metall. Mater. Trans. A, 1999, vol. 30A, pp. 1663–73.10.1007/s11661-999-0104-y ↗
33. W. Baos and M.E. Hargreaves: Proc. R. Soc., 1948, vol. A193, pp. 89–97.
34. G.E. Dieter: Mechanical Metallurgy, 3rd ed., McGraw-Hill Book Co., Boston, MA, 1986, pp. 290 and 308.
35. M. Dao, L. Lu, R.J. Asaro, J.T.M. De Hosson, and E. Ma: Acta Metall., 2007, vol. 55, pp. 4041–65.
36. Y.M. Wang and E. Ma: Acta Mater., 2004, vol. 52, pp. 1699–09.10.1016/j.actamat.2003.12.022 ↗