journal article·2009-02

On the Extension of Processing Time with Increase in Temperature during Transient-Liquid Phase Bonding

M.M. Abdelfatah, O.A. Ojo

Publisher page

Abstract

Transient-liquid phase (TLP) bonding of a nickel-based superalloy, IN 738, was performed. Contrary to conventional TLP bonding analytical models, which assume a parabolic relationship between liquid/solid interface migration and holding time, deviation from this law was observed experimentally and by numerical simulation. The deviation, which is caused by reduction in solute concentration gradient below a critical value, is suggested as an alternate phenomenon responsible for anomalous extension of processing time required to produce an eutectic-free joint with increase in bonding temperature. A decrease in the filler gap size and the use of a melting-point depressant (MPD) solute with higher solubility in the base material could reduce the occurrence of the anomalous behavior during a high-temperature TLP joining process.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Solidification and crystal growth phenomena · High Temperature Alloys and Creep · Metallurgical Processes and Thermodynamics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (20)

Show source-provided references
1. J.M. Vitek: Acta Mater., 2005, vol. 53, pp. 53–6710.1016/j.actamat.2004.08.039 ↗
2. J.N. DuPont, C.V. Robino, A.R. Marder, M.R. Notis: Metall. Mater. Trans. A, 1998, vol. 29A, pp. 2797–80610.1007/s11661-998-0320-x ↗
3. M.B. Henderson, D. Arrell, M. Larsson, G. Marchant: Sci. Technol. Weld. Join., 2004, vol. 9, pp. 13–2110.1179/136217104225017099 ↗
4. D.S. Duvall, W.A. Owczarski, D.F. Paulonis: Weld. J., 1974, vol. 53, pp. 203–14
5. O.A. Idowu, N.L. Richards, M.C. Chaturvedi: Mater. Sci. Eng. A, 2005, vol. 397, pp. 98–11210.1016/j.msea.2005.01.055 ↗
6. K. Tokoro, N. Wikstrom, O.A. Ojo, M.C. Chaturvedi: Mater. Sci. Eng. A, 2008, vol. 477, pp. 311–1810.1016/j.msea.2007.05.069 ↗
7. O.A. Ojo, N.L Richards, M.C. Chaturvedi: Metall. Mater. Trans. A, 2006, vol. 37A, pp. 421–3310.1007/s11661-006-0013-2 ↗
8. P. Villars, A. Prince, H. Okamoto: Handbook of Ternary Alloy Phase Diagrams, ASM INTERNATIONAL, Metals Park, OH, 1993
9. Y. Zhou, W.F. Gale, T.H. North: Int. Mater. Rev., 1995, vol. 40, pp. 181–9610.1179/imr.1995.40.5.181 ↗
10. I. Tuah-Poku, M. Dollar, T.B. Massalski: Metall. Mater. Trans. A, 1988, vol. 19A, pp. 675–8610.1007/BF02649282 ↗
11. W.D. MacDonald, T.W. Eagar: Metall. Mater. Trans. A, 1998, vol. 29A, pp. 315–2510.1007/s11661-998-0183-1 ↗
12. S. Liu, D.L. Olson, G.P. Martin, G.R. Edwards: Weld. J., 1991, vol. 70, pp. 207s–215s
13. Y. Nakao, K. Nishimoto, K. Shinozaki, C.Y. Kang: Trans. Jpn. Weld. Soc., 1989, vol. 20, pp. 60–65
14. W.F. Gale, E.R. Wallach: Mater. Sci Technol., 1991, vol. 7, pp. 1143–4810.1179/mst.1991.7.12.1143 ↗
15. T.C. Illingworth, I.O. Golosnoy: J. Comp. Phys., 2005, vol. 209, pp. 207–2510.1016/j.jcp.2005.02.031 ↗
16. M.L. Kuntz: Ph.D. Dissertation, University of Waterloo, Waterloo, 2006
17. A. Sakamoto, C. Fujiwara, T. Hattori, S. Sakai: Weld. J., 1989, vol. 68, pp. 63–71
18. J.E. Ramirez, S. Liu: Weld. J., 1992, vol. 71, pp. 365s–375s
19. C.W. Sinclair, G.R. Purdy, J.E. Morral: Metall. Mater. Trans. A, 2000, vol. 31A, pp. 1187–9210.1007/s11661-000-0114-2 ↗
20. R. Johnson: Weld. J., 1981, vol. 60, pp. 185s–193s