Effect of Bonding Temperature on Interfacial Reaction and Mechanical Properties of Diffusion-Bonded Joint Between Ti-6Al-4V and 304 Stainless Steel Using Nickel as an Intermediate Material
Source abstract
Abstract
An investigation was carried out on the solid-state diffusion bonding between Ti-6Al-4V (TiA) and 304 stainless steel (SS) using pure nickel (Ni) of 200-μm thickness as an intermediate material prepared in vacuum in the temperature range from 973 K to 1073 K (700 °C to 800 °C) in steps of 298 K (25 °C) using uniaxial compressive pressure of 3 MPa and 60 minutes as bonding time. Scanning electron microscopy images, in backscattered electron mode, had revealed existence of layerwise Ti-Ni-based intermetallics such as either Ni3Ti or both Ni3Ti and NiTi at titanium alloy-nickel (TiA/Ni) interface, whereas nickel-stainless steel (Ni/SS) diffusion zone was free from intermetallic phases for all joints processed. Chemical composition of the reaction layers was determined in atomic percentage by energy dispersive spectroscopy and confirmed by X-ray diffraction study. Room-temperature properties of the bonded joints were characterized using microhardness evaluation and tensile testing. The maximum hardness value of ~800 HV was observed at TiA/Ni interface for the bond processed at 1073 K (800 °C). The hardness value at Ni/SS interface for all the bonds was found to be ~330 HV. Maximum tensile strength of ~206 MPa along with ~2.9 pct ductility was obtained for the joint processed at 1023 K (750 °C). It was observed from the activation study that the diffusion rate at TiA/Ni interface is lesser than that at the Ni/SS interface. From microhardness profile, fractured surfaces and fracture path, it was demonstrated that failure of the joints was initiated and propagated apparently at the TiA/Ni interface near Ni3Ti intermetallic phase.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Intermetallics and Advanced Alloy Properties · Advanced Welding Techniques Analysis · Titanium Alloys Microstructure and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (31)
Show source-provided references
1. H. Arik, M. Aydin, A. Kurt, and M. Turker: Mater. Des., 2005, vol. 26, pp. 555–60.10.1016/j.matdes.2004.07.017 ↗
2. J.M. Gómez de Salazar, A. Ureña, and J.G. Carrión: Scripta Mater., 1996, vol. 35, pp. 479–84.10.1016/1359-6462(96)00177-7 ↗
3. M. Holmquist, V. Recina, J. Ockborn, B. Pettersson, and E. Zumalde: Scr. Mater., 1998, vol. 39, pp. 1101–06.10.1016/S1359-6462(98)00274-7 ↗
4. M.S. Yeh and T.H. Chuang: Scr. Metall. Mater., 1995, vol. 33, pp. 1277–81.10.1016/0956-716X(95)00364-2 ↗
5. S. Fukumoto, A. Hirose, and K.F. Kobayashi: Compos. Eng., 1995, vol. 5, pp. 1081–89.10.1016/0961-9526(95)00060-Z ↗
6. N. Kahraman, B. Gulenc, and F. Findik: Int. J. Impact Eng., 2007, vol. 34, pp. 1423–32.10.1016/j.ijimpeng.2006.08.003 ↗
7. Z. Sun, I. Annergren, D. Pan, and T.A. Mai: Mater. Sci. Eng., A, 2003, vol. 345, pp. 293–300.10.1016/S0921-5093(02)00477-X ↗
8. G. Thomas and V. Ramachandra: Internal Report, Vikram Sarabhai Space Center, Trivandrum, 1981, pp. 1–14.
9. C. Xia and Z. Jin: J. Less-Common Met., 1990, vol. 162, pp. 315–22.10.1016/0022-5088(90)90347-M ↗
10. A. Fuji, K. Ameyama, and T.H. North: J. Mater. Sci., 1996, vol. 31, pp. 819–27.10.1007/BF00367903 ↗
11. K. Bhanumurthy and G.B. Kale: J. Mater. Sci. Lett., 1993, vol. 12, pp. 1879–81.10.1007/BF00540018 ↗
12. B. Alemán, L. Gutiérrez, and J.J. Urcola: Mater. Sci. Technol., 1993, vol. 9, pp. 633–41.10.1179/mst.1993.9.8.633 ↗
13. G. Cam and M. Kocak: Int. Mater. Rev., 1998, vol. 43, pp. 1–44.10.1179/imr.1998.43.1.1 ↗
14. S. Hinotani and Y. Ohmori: Trans. Jpn. Inst. Met., 1988, vol. 29, pp. 116–24.10.2320/matertrans1960.29.116 ↗
15. P. He, J. Zhang, R. Zhou, and X. Li: Mater. Charact., 1999, vol. 43, pp. 287–92.10.1016/S1044-5803(99)00008-X ↗
16. S. Kundu, S. Chatterjee, D. Olson, and B. Mishra: Metall. Mater. Trans. A, 2007, vol. 38, pp. 2053–60.10.1007/s11661-007-9273-8 ↗
17. M. Ghosh, S. Kundu, S. Chatterjee, and B. Mishra: Metall. Mater. Trans. A, 2005, vol. 36, pp. 1891–99.10.1007/s11661-005-0052-0 ↗
18. H. Kato, S. Abe, and T. Tomizawa: J. Mater. Sci., 1997, vol. 32, pp. 5225–32.10.1023/A:1018694106588 ↗
19. S. Kundu, and S. Chatterjee: Mater. Sci. Eng., A, 2006, vol. 425, pp. 107–13.10.1016/j.msea.2006.03.034 ↗
20. S. Kundu, G. Anand, and S. Chatterjee: Metall. Mater. Trans. A, 2013, vol. 44, pp. 2196–211.10.1007/s11661-012-1553-2 ↗
21. Annual Book of ASTM E8M-11 Standard, vol. 03.01, ASTM, Philadelphia, PA, 2012.
22. W.F. Hosford: Physical Metallurgy, 1st Indian Reprint, CRC, Boca Raton, 2008, pp. 87–88, 101–07.
23. T. Fischer: Materials Science for Engineering Students, 1st Indian Reprint, Academic Press, San Diego, 2009, pp. 19–21.
24. M. Ghosh and S. Chatterjee: Mater. Sci. Eng., A, 2003, vol. 358, pp. 152–58.10.1016/S0921-5093(03)00298-3 ↗
25. B. Alemán, I. Gutiérrez, and J. J. Urcola: Metall. Mater. Trans. A, 1995, vol. 26, pp. 437–46.10.1007/BF02664680 ↗
26. W.F. Smith: Principles of Materials Science and Engineering, 2nd ed., McGraw-Hill, New York, 1990, pp. 290–96.
27. D.R. Askeland and P.P. Phulé: The Science and Engineering of Materials, 1st Indian Reprint, Thomson, Singapore, 2003, pp. 182–95.
28. E. Atasoy and N. Kahraman: Mater. Charact., 2008, vol. 59, pp. 1481–90.10.1016/j.matchar.2008.01.015 ↗
29. D.A. Porter, K.E. Easterling, and M.Y. Sherif: Phase Transformations in Metals and Alloys, 3rd ed., CRC, Boca Raton, 2009, pp. 63–83.
30. S. Kundu and S. Chatterjee: ISIJ Int., 2009, vol. 49, pp. 1749–54.10.2355/isijinternational.49.1749 ↗
31. T. Vigraman, D. Ravindran, and R. Narayanasamy: Mater. Des., 2012, vol. 36, pp. 714–27.10.1016/j.matdes.2011.12.024 ↗