journal article·2019-09-15

Friction Stir Welding of Low-Carbon Shipbuilding Steel Plates: Microstructure, Mechanical Properties, and Corrosion Behavior

D. M. Sekban, S. M. Aktarer, G. Purcek

Publisher page

Abstract

In this study, low-carbon steel plates (ASTM 131A) used generally in shipbuilding applications were joined by friction stir welding (FSW) using optimum processing parameters. The microstructure, mechanical properties, formability, and corrosion behavior of the joint were investigated. From the results of the investigation, it was discovered that two distinct regions, stir zone (SZ) and heat-affected zone (HAZ), were formed in the welded region during FSW of the plates. FSW decreased the ferritic grain size of the SZ from 25 µm to about 4 µm. Refined grains were separated mostly by a high angle of misorientation with the low amount of dislocations. The hardness of the SZ increased from 140 Hv0.3 to about 230 Hv0.3. The yield and tensile strength values of the SZ increased from 256 and 435 MPa to about 457 and 585 MPa, respectively, by the effect of FSW without a considerable decrease in ductility. FSW did not cause a significant change in the formability of the joint. Displacement at the maximum bending force decreased slightly after FSW from 6.31 mm to about 5.69 mm. Also, corrosion resistance after FSW slightly increased as a result of grain refinement. Current density values were obtained as 3.36 × 10−6 A/cm2 (base material 4.44 × 10−6 A/cm2).
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Welding Techniques Analysis · Welding Techniques and Residual Stresses · Metal Forming Simulation Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (70)

Show source-provided references
1. K. Masubuchi: Welding Problems in Shipbuilding, 1969, SNAME.10.5957/mt1.1969.6.1.66 ↗
2. J.Q. Su, T.W. Nelson, R. Mishra, and M. Mahoney: Acta Mater., 2003, vol. 51(3), pp. 713-29.10.1016/S1359-6454(02)00449-4 ↗
3. C.G. Rhodes, M.W. Mahoney, W.H. Bingel, R.A. Spurling, and C.C. Bampton: Scripta Mater., 1997, vol. 36(1), pp. 69-75.10.1016/S1359-6462(96)00344-2 ↗
4. N. Xu, Q. Song, and Y. Bao: Mater. Lett., 2017, vol. 205, pp. 219-22.10.1016/j.matlet.2017.06.043 ↗
5. W. Han, P. Liu, X. Yi, Q. Zhan, F. Wan, K. Yabuuchi, H. Serizawa, and A. Kimura: J. Mater. Sci. Technol., 2017, vol. 34(1), pp. 209-13.10.1016/j.jmst.2017.11.032 ↗
6. Z. Liu, R. Xin, D. Liu, X. Shu, and Q. Liu: Mater. Sci. Eng. A., 2016, vol. 658, pp. 185-91.10.1016/j.msea.2016.01.097 ↗
7. B. Davoren, E.E. Ferg, and D. Hattingh: Wear, 2017, vol. 390-91, pp. 246-52.10.1016/j.wear.2017.08.004 ↗
8. A. Tongne, M. Jahazi, E. Feulvarch, and C. Desrayaud: J. Mater. Process. Tech., 2015, vol. 221, pp. 269-78.10.1016/j.jmatprotec.2015.02.020 ↗
9. R.S. Mishra and Z.Y. Ma: Mater. Sci. Eng. R Rep., 2005, vol. 50, pp. 1–78.10.1016/j.mser.2005.07.001 ↗
10. Y.S. Sato and H. Kokawa: Weld. Int., 2003, vol. 17(11), pp. 852-55.10.1533/wint.2003.3174 ↗
11. W.M. Thomas and E.D. Nicholas: Mater. Design., 1997, vol. 18(4), pp. 269-73.10.1016/S0261-3069(97)00062-9 ↗
12. A. Toumpis, A. Galloway, S. Cater, and N. McPherson: Mater. Design., 2014, vol. 62, pp. 64-75.10.1016/j.matdes.2014.04.066 ↗
13. C. Tingey, A. Galloway, A. Toumpis, and S. Cater: Mater. Design., 2015, vol. 65, pp. 896-906.10.1016/j.matdes.2014.10.017 ↗
14. S. Karami, H. Jafarian, A.R. Eivani, and S. Kheirandish: Mater. Sci. Eng. A., 2016, vol. 670, pp. 68-74.10.1016/j.msea.2016.06.008 ↗
15. A.N. Siddiquee, S. Pandey, and N.Z. Khan: Mater. Today Proc., 2015, vol. 2(4), pp. 1388-97.10.1016/j.matpr.2015.07.058 ↗
16. S. Sabooni, F. Karimzadeh, M.H. Enayati, and A.H.W. Ngan: Mater. Design., 2015, vol. 76, pp. 130-40.10.1016/j.matdes.2015.03.052 ↗
17. K.H. Kim, H.S. Bang, H.S. Bang, and A.F.H. Kaplan: J. Mater. Process. Tech., 2017, vol. 243, pp. 381-86.10.1016/j.jmatprotec.2016.12.018 ↗
18. M. Al-moussawi, A.J. Smith, A. Young, S. Cater, and M. Faraji: Int. J. Adv. Manuf. Tech., 2017, vol. 92(1), pp. 341-60.10.1007/s00170-017-0147-y ↗
19. A. Toumpis, A. Galloway, L. Molter, and H. Polezhayeva: Mater. Design., 2015, vol. 80, pp. 116-28.10.1016/j.matdes.2015.04.046 ↗
20. T.J. Lienert, W.L. Stellwag, B.B. Grimmett, and W.W. Warke: Weld. J., 2003, vol. 82, pp. 1-9.10.1179/136217103225008847 ↗
21. Y.S. Sato, H. Yamanoi, H. Kokawa, and T. Furuhara: Isij. Int., 2008, vol. 48(1), pp. 71-76.10.2355/isijinternational.48.71 ↗
22. V. Manvatkar, A. De, L.E. Svensson, and T. DebRoy: Scripta Mater., 2015, vol. 94, pp. 36-39.10.1016/j.scriptamat.2014.09.012 ↗
23. Y.D. Chung, H. Fujii, R. Ueji, and N. Tsuji: Scripta Mater., 2010, vol. 63(2), pp. 223-26.10.1016/j.scriptamat.2010.03.060 ↗
24. M. Imam, R. Ueji, and H. Fujii: Mater. Sci. Eng. A., 2015, vol. 636, pp. 24-34.10.1016/j.msea.2015.03.089 ↗
25. R. Ramesh, I. Dinaharan, R. Kumar, and E.T. Akinlabi: Mater. Sci. Eng. A., 2017, vol. 687, pp. 39-46.10.1016/j.msea.2017.01.050 ↗
26. S.A. Khodir, Y. Morisada, R. Ueji, and H. Fujii: Mater. Sci. Eng. A., 2012, vol. 558, pp. 572-78.10.1016/j.msea.2012.08.052 ↗
27. H.B. Cui, G.M. Xie, Z.A. Luo, J. Ma, G.D. Wang, and R.D.K. Misra: J. Alloy. Compd., 2016, vol. 681, pp. 426-33.10.1016/j.jallcom.2016.03.299 ↗
28. T.W. Nelson and S.A. Rose: J. Mater. Process. Tech., 2016, vol. 231, pp. 66-74.10.1016/j.jmatprotec.2015.12.013 ↗
29. M.M. Husain, R. Sarkar, T.K. Pal, N. Prabhu, and M. Ghosh: J. Mater. Eng. Perform., 2015, vol. 24(9), pp. 3673-83.10.1007/s11665-015-1652-5 ↗
30. S. Sabooni, F. Karimzadeh, M.H. Enayati, A.H.W. Ngan, and H. Jabbari: Mater. Charact., 2015, vol. 109(Supplement C), pp. 138–51.10.1016/j.matchar.2015.08.009 ↗
31. A.N. Siddiquee and S. Pandey: Int. J. Adv. Manuf. Tech., 2014, vol. 73(1), pp. 479-86.10.1007/s00170-014-5846-z ↗
32. H.-H. Cho, S.-T. Hong, J.-H. Roh, H.-S. Choi, S.H. Kang, R.J. Steel, and H.N. Han: Acta Mater., 2013, vol. 61(7), pp. 2649-61.10.1016/j.actamat.2013.01.045 ↗
33. J.J. Jeon, S. Mironov, Y.S. Sato, H. Kokawa, S.H.C. Park, and S. Hirano: Metall. Mater. Trans. A., 2013, vol. 44(7), pp. 3157-66.10.1007/s11661-013-1692-0 ↗
34. H. Fujii, L. Cui, K. Nakata, and K. Nogi: Weld. World, 2008, vol. 52(9), pp. 75-81.10.1007/BF03266672 ↗
35. S. Shashi Kumar, N. Murugan, and K.K. Ramachandran: Int. J. Refract. Met. H., 2016, vol. 58(Supplement C), pp. 196-205.10.1016/j.ijrmhm.2016.04.015 ↗
36. H. Dawson, M. Serrano, R. Hernandez, S. Cater, and E. Jimenez-Melero: Mater. Sci. Eng. A., 2017, vol. 693, pp. 84-92.10.1016/j.msea.2017.03.090 ↗
37. Y. Sun and H. Fujii: Mater. Sci. Eng. A., 2017, vol. 694, pp. 81-92.10.1016/j.msea.2017.04.008 ↗
38. H. Kokawa, S.H.C. Park, Y.S. Sato, K. Okamoto, S. Hirano, and M. Inagaki: Weld. World, 2005, vol. 49(3), pp. 34-40.10.1007/BF03266473 ↗
39. A.K. Lakshminarayanan and V. Balasubramanian: Met. Mater-Int., 2011, vol. 17(6), pp. 969-81.10.1007/s12540-011-6016-6 ↗
40. H. Dawson, M. Serrano, S. Cater, N. Iqbal, L. Almásy, Q. Tian, and E. Jimenez-Melero: J. Nucl. Mater., 2017, vol. 486, pp. 129-37.10.1016/j.jnucmat.2016.12.033 ↗
41. R. Johnson and P.L. Threadgill: Adv. Mar. Mater.: Tech. Appl., 2003, pp. 1-6.
42. J. Martin and S. Wei: Friction Stir Welding Technology for Marine Applications, in: R.S. Mishra, M.W. Mahoney, Y. Sato, and Y. Hovanski (Eds.), Friction Stir Welding and Processing VIII, Springer International Publishing, Cham, 2016, pp. 219-26.
43. A. Toumpis, A. Galloway, S. Cater, P. Burling, and C. Stanhope: 33rd International Conference on Ocean, Offshore and Arctic Engineering, 2014.
44. Y. Huang, Y. Xie, X. Meng, Z. Lv, and J. Cao: J. Mater. Proc. Technol.,vol. 252, pp. 233-41.10.1016/j.jmatprotec.2017.09.029 ↗
45. L. Fratini and G. Buffa: P. I. Mech. Eng. B.-J. Eng., 2007, vol. 221(5), pp. 857-64.
46. H.S. Arora, H. Singh, and B.K. Dhindaw: Int. J. Adv. Manuf. Tech., 2012, vol. 61(9), pp. 1043-55.10.1007/s00170-011-3758-8 ↗
47. Y.N. Zhang, X. Cao, S. Larose, and P. Wanjara: Can. Metall. Quart., 2012, vol. 51(3), pp. 250-61.10.1179/1879139512Y.0000000015 ↗
48. Z.Y. Ma: Metall. Mater. Trans. A., 2008, vol. 39(3), pp. 642-58.10.1007/s11661-007-9459-0 ↗
49. X. He, F. Gu, and A. Ball: Prog. Mater. Sci., 2014, vol. 65, pp. 1-66.10.1016/j.pmatsci.2014.03.003 ↗
50. S. Tutunchilar, M. Haghpanahi, M.K. Besharati Givi, P. Asadi, and P. Bahemmat: Mater. Design., 2012, vol. 40, pp. 415-26.10.1016/j.matdes.2012.04.001 ↗
51. D.M. Sekban, S.M. Aktarer, H. Zhang, P. Xue, Z. Ma, and G. Purcek: Metall. Mater. Trans. A., 2017, vol. 48(8), pp. 3869-79.10.1007/s11661-017-4157-z ↗
52. S.F. Di Martino and G. Thewlis: Metall. Mater. Trans. A., 2014, vol. 45(2), pp. 579-94.10.1007/s11661-013-2035-x ↗
53. J.C. Lippold: Welding Metallurgy Principles, Welding Metallurgy and Weldability, John Wiley & Sons, 2015, pp. 9-83.10.1002/9781118960332 ↗
54. P.L. Threadgill: Sci. Technol. Weld. Joi., 2007, vol. 12(4), pp. 357-60.10.1179/174329307X197629 ↗
55. B. Burton: Philos. Mag. A., 2002, vol. 82(11), pp. 2303-20.10.1080/01418610208235740 ↗
56. I. Milas and E.A. Carter: J. Mater. Sci., 2009, vol. 44(7), pp. 1741-49.10.1007/s10853-008-3191-z ↗
57. Y. Sugino, S. Ukai, B. Leng, N. Oono, S. Hayashi, T. Kaito, and S. Ohtsuka: J. Nucl. Mater., 2014, vol. 452(1), pp. 628-32.10.1016/j.jnucmat.2014.05.040 ↗
58. J.-Q. Su, T.W. Nelson, and C.J. Sterling: Mater. Sci. Eng. A., 2005, vol. 405(1), pp. 277-86.10.1016/j.msea.2005.06.009 ↗
59. P.B. Prangnell and C.P. Heason: Acta Mater., 2005, vol. 53(11), pp. 3179-92.10.1016/j.actamat.2005.03.044 ↗
60. M. Hajian, A. Abdollah-zadeh, S.S. Rezaei-Nejad, H. Assadi, S.M.M. Hadavi, K. Chung, and M. Shokouhimehr: Mater. Design, 2015, vol. 67, pp. 82-94.10.1016/j.matdes.2014.10.082 ↗
61. D.M. Sekban, O. Saray, S.M. Aktarer, G. Purcek, and Z.Y. Ma: Mater. Sci. Eng. A., 2015, vol. 642, pp. 57-64.10.1016/j.msea.2015.06.068 ↗
62. D.M. Sekban, S.M. Aktarer, P. Xue, Z.Y. Ma, and G. Purcek: Mater. Sci. Eng. A., 2016, vol. 672, pp. 40-48.10.1016/j.msea.2016.06.063 ↗
63. A. Chabok and K. Dehghani: J. Mater. Eng. Perform., 2013, vol. 22(5), pp. 1324-30.10.1007/s11665-012-0424-8 ↗
64. N. Kahraman, B. Gülenç, and A. Durgutlu: Gümüşhane Üniversitesi Fen Bilimleri Dergisi, 2005, vol. 18(3), pp. 473-80.
65. J.H. Kim, Y.J. Oh, I.S. Hwang, D.J. Kim, and J.T. Kim: J. Nucl. Mater., 2001, vol. 299(2), pp. 132-39.10.1016/S0022-3115(01)00688-2 ↗
66. O. Saray, G. Purcek, I. Karaman, and H.J. Maier: Metall. Mater. Trans. A., 2013, vol. 44(9), pp. 4194-206.10.1007/s11661-013-1781-0 ↗
67. O. Saray, G. Purcek, I. Karaman, and H.J. Maier: Mater. Sci. Eng. A., 2014, vol. 619, pp. 119-28.10.1016/j.msea.2014.09.016 ↗
68. D.M. Sekban, S.M. Akterer, O. Saray, Z.Y. Ma, and G. Purcek: J. Mater. Sci. Technol., 2018, vol. 34(1), pp. 237-44.10.1016/j.jmst.2017.10.020 ↗
69. A. Di Schino and J.M. Kenny: J. Mater. Sci. Lett., 2002, vol. 21(20), pp. 1631-34.10.1023/A:1020338103964 ↗
70. M. Hasegawa and M. Osawa: Corrosion-Us., 1984, vol. 40(7), pp. 371-74.10.5006/1.3593940 ↗