journal article·2019-08-15

Microstructural Characterization of Aluminum 6061 Splats Cold Spray Deposited on Aluminum 6061-T6 Substrate

Wendy C. Evans, Xingdong Dan, Azin Houshmand, Sinan Müftü, Teiichi Ando

Publisher page

Abstract

The microstructural evolution at the interface of Al6061 splats cold sprayed on Al6061 substrate at a supercritical impact velocity was investigated by SEM and S/TEM. Metallurgical bonding was observed in the peripheral (equatorial) region of the splat where a localized outward material flow promoted by continuous dynamic recrystallization (CDRX) occurred to displace the oxide from the interface. No recrystallization or metallurgical bonding was observed at the polar interface where oxide remained in fragments. CDRX produced elongated grains less than 100 nm thick at the equatorial interface which transformed to slightly coarsened (100 to 200 nm) ultrafine grains in the splat side of the interface. Rapid precipitation on the boundaries of recrystallized grains and in the unrecrystallized regions of the splat–substrate interface was discussed in relation to the sequence of structural evolution at the splat–substrate interface during the impact and subsequent cooling. Further work is needed to more fully understand the kinetics of dynamic recovery/recrystallization and precipitation in the presence of excess vacancies that can have impact on the dislocation mobility, mass transport, and thermodynamic stability.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High-Temperature Coating Behaviors · Metal Alloys Wear and Properties · Advanced ceramic materials synthesis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (65)

Show source-provided references
1. H. Assadi, F. Gartner, T. Stoltenhoff and H. Kreye, Acta. Mater. 2003, vol. 51(3), pp. 4379-94.10.1016/S1359-6454(03)00274-X ↗
2. V. K. Champagne, The Cold Spray Materials Deposition Process: Fundamentals and Applications, CRC Press, Cambridge, 2007.10.1201/9781439824122 ↗
3. A. Mordi, S. Hassani-Gangaraj, M. Guangliano and M. Dao, Surf. Eng., 2014, vol. 30(6), pp. 369-95.10.1179/1743294414Y.0000000270 ↗
4. W.B. Choi, L. Li, V. Luzin, R. Neiser, T. Gnaupel-Herold, H.J. Prask, S. Sampath and A. Gouldstone, Acta Mater., 2007, vol. 55, pp. 857-66.10.1016/j.actamat.2006.09.006 ↗
5. T. Schmidt, H. Assadi, F. Gartner, H. Ritcher, T. Stoltenhoff, H. Kreye and T. Kiassen, J. Therm. Spray Tech., 2009, vol. 18(5-6), pp. 794-808.10.1007/s11666-009-9357-7 ↗
6. W. Wong, E. Irissou, A. N. Ryabinin, J.-G. Legoux, S. Yue, J. Therm. Spray Tech., 2011, 20(1-2), pp. 213-26.10.1007/s11666-010-9568-y ↗
7. M. Fukumoto, H. Terada, M. Mashiko, K. Sato, M. Yamada and E. Yamaguchi, Mater. Trans. 2009, vol. 50(6), pp.1482-88.10.2320/matertrans.MRA2008223 ↗
8. F. Chen, F. Li, Q. Shen and L. Zhang, J. Phys. Conf. Series, 2006, 419(1), 012006.10.1088/1742-6596/507/1/012006 ↗
9. P.C. King, A.J. Poole, S, Horne, R. de Nys, S. Gulizia and M.Z. Jahedi, Surf. Coat. Tech., 2013, vol. 216, pp. 60-67.10.1016/j.surfcoat.2012.11.023 ↗
10. H. Che, P. Vo and S. Yue, Surf. Coat. Tech., 2017, vol. 313, pp. 236-47.10.1016/j.surfcoat.2017.01.083 ↗
11. D. Zhang, P.H. Shipway and D.G. McCartney, J. Therm. Spray Tech., 2005, vol. 14(1), pp. 109-16.10.1361/10599630522666 ↗
12. K. Ko, J. Choi and H. Lee, Mater. Let., 2016, vol. 175(15), pp.13-15.10.1016/j.matlet.2016.03.132 ↗
13. J. Villafuerte and D. Wright, Adv. Mater. Proc., 2010, vol. 168(5), pp. 53-55.
14. P. Cavaliere and A.Silvello, J. Therm. Spray Tech., 2017, vol. 26(4), pp. 661-70.10.1007/s11666-017-0534-9 ↗
15. C.A. Widener, M.J. Carter, O.C. Ozdemir, R.H. Hrabe, B. Hoiland, T.E. Stamey, V.K. Champagne and T.J. Eden, J. Therm. Spray Tech., 2016, vol. 25(1-2), pp. 193-201.10.1007/s11666-015-0366-4 ↗
16. A. Sova, S. Grigoriev, A. Okunkova and I. Smurov, Int. J. Adv. Manuf. Tech., 2013, vol. 69(9-12), pp. 2269-78.10.1007/s00170-013-5166-8 ↗
17. J. Pattison, S. Clotto, R. Morgan, M. Bray, W. Neill, Int. J. Machine Tools Manuf., 2007, 47, 627-34.10.1016/j.ijmachtools.2006.05.001 ↗
18. Y. Cormier, P. Dupuis, B. Jodoin and A. Corbeil, J. Therm. Spray Tech., 2013, vol. 22(7), pp. 1210-21.10.1007/s11666-013-9968-x ↗
19. M. Rokni, C. Widener and V. K. Champagne, J. Therm. Spray Tech., 2014, vol. 23 (3), pp. 514-524.10.1007/s11666-013-0049-y ↗
20. M. Rokni, C. Widener and G. Crawford, Surf. Coat. Tech., 2014, vol. 251, pp. 254-63.10.1016/j.surfcoat.2014.04.035 ↗
21. M. Rokni, C. Widener, G. Crawford and M.K. West, Mater. Sci. Eng. A, 2015, vol. 625, pp. 19-27.10.1016/j.msea.2014.11.059 ↗
22. Y. Zou, W. Qin, E. Irissou, J.-G. Legoux, S. Yue and J.A. Szpunar, Scr. Mater. 2009, vol. 61(9), pp. 899-902.10.1016/j.scriptamat.2009.07.020 ↗
23. T. Van Steenkiste and J.R. Smith, J. Therm. Spray Tech., 2004, vol. 13(2), pp. 274-82.10.1361/10599630419427 ↗
24. S.H. Zahiri, D. Fraser, S. Gulizia and M. Jehedi, J. Therm. Spray Tech., 2006, vol. 15(3), pp. 422-30.10.1361/105996306X124437 ↗
25. Y. Li, Y. Hamada, K. Otobe and T. Ando, J. Therm. Spray Tech., 2017, vol. 26(3), pp. 350-59.10.1007/s11666-016-0517-2 ↗
26. T. Hussain, D.G. McCartney, P.H. Shipway and D. Zhang, J. Therm. Spray Tech., 2009, vol. 18(3), pp.364-79.10.1007/s11666-009-9298-1 ↗
27. G. Bae, J.-I. Jiang and C. Lee, Acta Mater., 2012, vol. 60(8), pp. 3524-35.10.1016/j.actamat.2012.03.001 ↗
28. M. Grujicic, C.L. Zhao, W.S. DeRosset and D. Helfritch, Mater. Design, 2004, vol. 25(8), pp. 681-88.10.1016/j.matdes.2004.03.008 ↗
29. K. Yokoyama, M. Watanabe, S. Kuroda, Y. Gotoh, T. Schmidt and F. Gartner, Mater. Trans., 2006, vol. 47(7), pp. 1697-1702.10.2320/matertrans.47.1697 ↗
30. R.A. Austin and D.L. McDowell, Int. J. Plasticity, 2011, vol. 27, pp. 1-24.10.1016/j.ijplas.2010.03.002 ↗
31. B. Yildirim, H. Fukanuma, T. Ando, A. Gouldstone and S. Müftü, J. Trib. 2014, 137(1), 011102-1-1310.1115/1.4028471 ↗
32. Q. Chen, A. Alizadeh-Dehkharghani, W. Xie, X. Wang, V. Champagne, A. Gouldstone, J.-H. Lee and S. Müftü, J. Therm. Spray Tech., 2018, 27, 641-53.10.1007/s11666-018-0712-4 ↗
33. W. Xie, A. Alizadeh-Dehkharghani+, Q. Chen+, V.K. Champagne, X. Wang, A. Nardi, S. Kooi, S. Müftü and J.-H. Lee, Scientific Reports, https://doi.org/10.1038/s41598-017-05104-7, 2017.10.1038/s41598-017-05104-7 ↗
34. R.G. Johnson and W.H. Cook: Proceedings of the 7th International Symposium on Ballistics, The Netherlands: The Hague, 1983, pp. 541-43.
35. A. Hulton, MS. thesis, Northeastern University, 2013, p. 50.
36. C. Borchers, F. Gartner, T. Stoltenhoff and H. Kreye, J. Appl. Phys., 2004, vol. 96(8), pp. 4288-92.10.1063/1.1789278 ↗
37. P.C. King, S.H. Zahiri and M. Jahedi, Metall. Mater. Trans. A, 2009, vol. 40A, pp. 2115-23.10.1007/s11661-009-9882-5 ↗
38. K.-H. Kim, M. Watanabe, J. Kawakita and S. Kuroda, Scr. Mater., 2008, vol. 59(7), pp.768-71.10.1016/j.scriptamat.2008.06.020 ↗
39. R.D. Doherty, D.A. Hughes, F.J. Humphreys, J.J. Jonas, D. Jensen, M.E. Kassner, W.E. King, T.R. Mcelley, H.J. Mcueen, A.D. Rollett, Mater. Sci. Eng. A, 1997, 238(2), 219-7410.1016/S0921-5093(97)00424-3 ↗
40. M.A. Meyers, V.F. Nesterenko, J.C. LaSalvia and Q. Xue, Mater. Sci. Eng. A, 2001, vol. 317(1-2), pp. 204-25.10.1016/S0921-5093(01)01160-1 ↗
41. T. Sakai, A. Belyakov, R. Kaibyshev, H. Miura and J.J. Jonus, Prog. Mater. Sci., 2014, vol. 60, pp. 130-207.10.1016/j.pmatsci.2013.09.002 ↗
42. Y.B. Xu, J.G. Zhang, Y.L. Bai, and M.A. Meyers, Metall. Mater. Trans. A, 2008, vol. 39A, pp. 811-43.10.1007/s11661-007-9431-z ↗
43. H. Kreye, Welding Research Supplement, 1977, May, pp. 154s–158s.
44. F. Musin, A. Belyakov, R. Kaibyshev, Y. Motohashi, G. Itoh and K. Tsuzaki, Rev. Adv. Mater. Sci., 2010, vol. 25, pp. 107-12.
45. A. Belyakov and R. Kaibyshev, Nanostruct. Mater., 1995, vol. 6(5-8), pp. 893-96.10.1016/0965-9773(95)00203-0 ↗
46. D. Kuhlmann-Wilsdorf and N. Hansen, Scr. Metall. Mater., 1991, vol. 25(7), pp. 1557-62.10.1016/0956-716X(91)90451-6 ↗
47. E. Mariani and E. Ghassemieh, Acta Mater., 2010, vol. 58(7), 2492-503.10.1016/j.actamat.2009.12.035 ↗
48. C. Borchers, F. Gartner, T. Stoltenhoff, H. Kreye, Acta Mater., 2005, 53(1), 2991-3000.10.1016/j.actamat.2005.02.048 ↗
49. Q. Wang, N. Birbilis, and M.-X. Zhang, Mater. Let., 2011, vol. 65, pp. 1576 – 78.10.1016/j.matlet.2011.03.035 ↗
50. Q. Wang, D. Qiu, and Y. Xiong, N. Birbilis, M.-X. Zhang, Appl. Surf. Sci., 2014, vol. 289, pp. 366 – 69.10.1016/j.apsusc.2013.10.168 ↗
51. A.O. Tokarev, Metal Sci. Heat Treat., 1996, vol. 38(3), pp. 136-39.10.1007/BF01401446 ↗
52. C. Chen, Y. Xie, R. Huang, S. Deng, Z. Ren and H. Liao, Mater. Let., 2017, vol. 210, pp. 199-202.10.1016/j.matlet.2017.09.024 ↗
53. G. Bae, S. Kumar, S.-H. Yoon, K. Kang, H. Na, H.-J. Kim and C. Lee, Acta Mater., 2009, vol. 57, pp. 5654-66.10.1016/j.actamat.2009.07.061 ↗
54. B. A. Bedard, T.J. Flanagan, A.T. Ernst, A. Nardi, A.M. Dongare, H.D. Brody, C.K. Champagne Jr., S.-W. Lee and M. Aindow, J. Therm. Spray Tech., 2018, vol. 27(4), pp. 1563-78.10.1007/s11666-018-0785-0 ↗
55. M. Liu, J. Čížek, C.S.T. Chang and J. Banhart, Acta Mater., 2015, vol. 91, pp. 355–64.10.1016/j.actamat.2015.02.019 ↗
56. H. Q. Wang, W. L. Sun and Y. Q. Xing, Physics Procedia, 2013, vol. 50, pp. 68-75.10.1016/j.phpro.2013.11.013 ↗
57. C.-L. Chen and C.-H. Lin, Metals, 2017, vol. 7, 11, pp.1-8.
58. J.A. Hines and K.S. Vecchio, Acta Mater., 1997, vol. 45(2), pp. 635-649.10.1016/S1359-6454(96)00193-0 ↗
59. J.P. Hirth and J. Lothe, Theory of Dislocations, 2nd Ed., John Wiley & Sons, New York,1982, pp. 555-56.
60. K. Murty, K. Detemple, O. Kanert and J. Th. M. DeHosson, Met. Mater. Trans. A, 1998, vol. 29A, pp.153-59.10.1007/s11661-998-0168-0 ↗
61. M. Kiritani, Y. Satoh, Y. Kizuka, K. Arakawa, Y. Ogasawara, S. Arai, and Y. Shimomura, Philos. Mag. Lett. 1999, vol. 79(10), pp. 797-804.10.1080/095008399176616 ↗
62. R. W. Balluffi and D. N. Seidman, J. Appl. Phys., 1965, vol. 36(9), pp. 2708-11.10.1063/1.1714566 ↗
63. Z. Huang, K. Date, K. Tatsugawa, T. Ando, 1990 Metall. Mater. Trans. A, 49A, 6173-84.
64. I. E. Gunduz, T. Ando, E. Shattuck, P. Y. Wong, and C. C. Doumanidis, Scr. Mater., 2005, vol. 52, pp. 939-43.10.1016/j.scriptamat.2004.12.015 ↗
65. T. Hu, S. Zhalehpour, A. Gouldstone, S. Muftu and T. Ando, Metall. Mater. Trans. A, 2014, vol. 45A, pp. 2545-52.10.1007/s11661-014-2203-7 ↗