Application of Deep Cryogenic Treatment to Uncoated Tungsten Carbide Inserts in the Turning of AISI 304 Stainless Steel
Source abstract
Abstract
This study investigated the effects of deep cryogenic treatment (DCT) on the wear performance of uncoated tungsten carbide inserts. AISI 304 austenitic stainless steel, widely used in industry, was selected as the workpiece material. Cutting experiments showed that the amount of wear significantly increased with increasing cutting speed. In addition, it was found that DCT contributed to the wear resistance of the turning inserts. The treated turning inserts were less worn by 48 and 38 pct in terms of crater wear and notch wear, respectively, whereas they exhibited up to 18 pct superior wear performance in terms of flank wear. This was attributed to the precipitation of new and finer η-carbides and their homogeneous distribution in the microstructure of the tungsten carbide material after deep cryogenic treatment. Analyses via image processing, hardness measurements, and SEM observations confirmed these findings.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metal Alloys Wear and Properties · Advanced materials and composites · High Entropy Alloys Studies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (26)
Show source-provided references
1. S. Zhirafar, A. Rezaeian and M. Pugha: J. Mater. Process. Technol., 2007, vol. 186, pp. 298–303.10.1016/j.jmatprotec.2006.12.046 ↗
2. A. Bensely, A. Prabhakaran, D. M. Lal and G. Nagarajan: Cryogenics, 2006, vol. 45, pp. 747–54.10.1016/j.cryogenics.2005.10.004 ↗
3. S. Kalia: J Low Temp Phys, 2010, vol. 158, pp. 934–45.10.1007/s10909-009-0058-x ↗
4. P. Baldissera and C. Delprete: Mater. Des., 2009, vol. 30, pp. 1435–40.10.1016/j.matdes.2008.08.015 ↗
5. K. Vadivel and R. Rudramoorthy: Int. J. Adv. Manuf. Techno., 2009, vol. 42, pp. 222–32.10.1007/s00170-008-1597-z ↗
6. A. Akhbarizadeh, A. Shafyei and M.A. Golozar: Mater. Des. 2009, vol. 30, pp. 3259–64.10.1016/j.matdes.2008.11.016 ↗
7. V. Firouzdor, E. Nejati and F. Khomamizadeh: J. Mater. Process. Technol., 2008, vol. 206, pp. 467-72.10.1016/j.jmatprotec.2007.12.072 ↗
8. C. Bonilla, R. O’Meara and L. Perry: In Proceedings of the ASEE Annual Conference and Exposition, (2007), p. 9.
9. P. Paulin: Gear Technol., 1993, vol. 2, pp. 26-9.
10. N. Dhokey, A. Hake, S. Kadu, I. Bhoskar and G. Dey: Metall. Mater. Trans. A, 2014, vol. 45A, pp. 1508-16.10.1007/s11661-013-2067-2 ↗
11. A.Y.L. Yong, K.H.W. Seah and M. Rahman: Int. J. Mach. Tools Manuf., 2006, vol. 46, pp. 2051–6.10.1016/j.ijmachtools.2006.01.002 ↗
12. J.D. Darwin, D.M. Lal and D. Nagarajan: J. Mater. Process. Technol., 2008, vol. 195, pp. 241–7.10.1016/j.jmatprotec.2007.05.005 ↗
13. H.A. Stewart: Forest Prod. J., 2004, vol. 54, pp. 53-6.
14. W. E. Bryson: Cryogenics. Cincinnati: Hanser Gardner Publications, 1999, pp. 81–107.
15. S.S. Gill, R. Singh, H. Singh and J. Singh: Int. J. Mach. Tools Manuf., 2008, vol. 49, pp. 256–60.10.1016/j.ijmachtools.2008.11.001 ↗
16. N.A. Özbek, A. Çiçek, M. Gülesin and O. Özbek (2014) Int. J, Mach. Tools Manuf., vol. 86, pp. 34-43.10.1016/j.ijmachtools.2014.06.007 ↗
17. K.H.W. Seah, M. Yong and K.H. Rahman: Proc. Inst. Mech. Eng., 2003, vol. 217, pp. 29-43.10.1243/095440503762502260 ↗
18. T.V.S. Reddy, T. Sornakumar, M.V. Reddy and R. Venkatram: Int. J. Refract. Met. Hard Mater., 2009, vol. 27, pp. 181-5.10.1016/j.ijrmhm.2008.04.007 ↗
19. B.R. Ramji, H.N.N. Murthy and M. Krishna: Int. J. Eng. Sci. Technol., 2010, vol. 2, pp. 2521-9.
20. S.S. Gill, J. Singh, H. Singh and R. Singh: Int. J. Adv. Manuf. Technol., 2012, vol. 58, pp. 119-31.10.1007/s00170-011-3369-4 ↗
21. D. Thakur, B. Ramamoorthy and L. Vijayaraghavan: Mater. Lett., 2008, vol. 62, pp. 4403-6.10.1016/j.matlet.2008.07.043 ↗
22. K. Amini, A. Akhbarizadeh and S. Javadpour: Vacuum, 2012, vol. 86, pp. 1534-40.10.1016/j.vacuum.2012.02.013 ↗
23. N.A. Özbek, A. Çiçek, M. Gülesin and O. Özbek: Tribol. Int.,2016, vol. 94, pp. 223-33.10.1016/j.triboint.2015.08.024 ↗
24. G.E.D’Errico and R. Calzavarini: J. Mater. Process. Technol., 1995, vol. 54, pp. 34-9.10.1016/0924-0136(95)01916-2 ↗
25. K.V. Kumar and S.K. Choudhury: J. Mater. Process. Technol., 2008, vol. 203, pp. 95-101.10.1016/j.jmatprotec.2007.10.036 ↗
26. S. Singh, D. Singh and N.S. Kalsi (2012) Int. J. Adv. Eng. Technol., vol. 1, pp. 290-4.