Hot Tearing Susceptibility of Mg-Ca Binary Alloys
Source abstract
Abstract
Hot tearing is known as one of the most critical solidification defects commonly encountered during casting practice. As most Mg alloys are initially prepared by casting, ingots must have superior quality with no casting defects for the further processing. Due to the extensive potential biodegradable applications of binary Mg-Ca alloys, it is of great importance to investigate their hot tearing behavior. In the present study, the influence of Ca content (0.1, 0.2, 0.5, 1.0, and 2.0 wt pct) on hot tearing susceptibility (HTS) of Mg-Ca binary alloys was investigated using a constrained rod casting apparatus equipped with a load cell and data acquisition system. Tear volumes were quantified with 3D X-ray tomography. Results showed that the influence of Ca content on HTS followed a “Λ” shape: the HTS increased with increase in Ca content, reached a maximum at 0.5 to 1 wt pct Ca, and then decreased with further increasing the Ca content to 2.0 wt pct. The wide solidification range and reasonably high volume of intermetallic in the Mg-0.5 wt pct Ca and Mg-1 wt pct Ca alloys resulted in high HTS. Microstructure analysis suggested that the hot tear initiated at grain boundaries and propagated along them through thin film rupture or across the eutectic.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Magnesium Alloys: Properties and Applications · Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (42)
Show source-provided references
1. L. Katgerman and D.G. Eskin: Hot Cracking Phenomena in Welds II, Springer Berlin Heidelberg, Berlin, 2008, pp. 11-26.10.1007/978-3-540-78628-3_1 ↗
2. M.A. Easton, M.A. Gibson, S.M. Zhu, T.B. Abbott: Metall. Mater. Trans. A, 2014, vol 45, pp. 3586-95.10.1007/s11661-014-2272-7 ↗
3. Z. S. Zhen, N. Hort, Y. D. Huang, O. Utke, N. Petri and K. U. Kainer: Int. J. Cast. Metal. Res., 2009, vol. 22, pp. 331-34.10.1179/136404609X368145 ↗
4. G. Cao, C. Zhang, H. Cao, Y. A. Chang and S. Kou: Metall. Mater. Trans. A, 2010, vol. 41, pp. 706-16.10.1007/s11661-009-0134-5 ↗
5. Z. S. Zhen, N. Hort, Y. D. Huang, N. Petri, O. Utke and K. U. Kainer: Mater. Sci. Forum., 2009, vol. 618-619, pp. 533-40.10.4028/www.scientific.net/MSF.618-619.533 ↗
6. G. Cao and S. Kou: Mater. Sci. Eng. A, 2006, vol. 417, pp. 230-38.10.1016/j.msea.2005.10.050 ↗
7. J. Z. Zhu, J. Guo and M. T. Samonds: Int. J. Numer. Meth. Eng., 2011, vol. 87, pp. 289-308.10.1002/nme.3054 ↗
8. Z. Wang, Y. D. Huang, A. Srinivasan, Z. Liu, F. Beckmann, K. U. Kainer and N. Hort: Mater. Design. 2013, vol. 47, pp. 90-100.10.1016/j.matdes.2012.12.044 ↗
9. A. Srinivasan, Z. Wang, Y. D. Huang, F. Beckmann, K. U. Kainer and N. Hort: Metall. Mater. Trans. A, 2013, vol. 44, pp. 2285-98.10.1007/s11661-012-1593-7 ↗
10. W. Zheng, S. Li, B. Tang, D. Zeng and X. Guo: J. Rare Earth, 2006, vol. 24, pp. 346-51.10.1016/S1002-0721(06)60122-1 ↗
11. Y. Wang, Q. Wang, G. Wu, Y. Zhu and W. Ding: Mater. Lett., 2002, vol. 57, pp. 929-34.10.1016/S0167-577X(02)00898-4 ↗
12. S Li, B. Tang, X. Jin and D. Zeng: J. Mater. Sci., 2011, vol. 47, pp. 2000-04.10.1007/s10853-011-5997-3 ↗
13. B.R. Powell, A.A. Luo, B.L. Tiwari, and V. Rezhets: TMS, 2002, pp. 123–29.
14. G. Cao and S. Kou: Metall. Mater. Trans. A, 2006, vol. 37A, pp. 3647-63.10.1007/s11661-006-1059-x ↗
15. G G. Cao, I. Haygood and S. Kou: Metall. Mater. Trans. A, 2010, vol. 41, pp. 2139-50.10.1007/s11661-010-0248-9 ↗
16. L. Zhou, Y. D. Huang, P. L. Mao, K. U. Kainer, Z. Liu, and N. Hort: TMS, 2011, pp. 125–30.10.1007/978-3-319-48223-1_24 ↗
17. L. Zhou: Thesis, Shenyang University of Technology, Shenyang, 2011, pp. 150.
18. Q. D. Wang, W. D. Chen, X. Q. Zeng, Y. Z. Lu, W. J. Ding, Y. P. Zhu, X. P. Xu and M. Mabuchi: J. Mater. Sci., 2001, vol. 36, pp. 3035-40.10.1023/A:1017927109291 ↗
19. A. A. Luo, M. P. Balogh and B. R. Powell: Metall. Mater. Trans. A, 2002, vol. 33, pp. 567-74.10.1007/s11661-002-0118-1 ↗
20. W.-C. Kim, J.-G. Kim, J.-Y. Lee, H.-K. Seok: Mater. Lett., 2008, vol. 62, pp. 4146-48.10.1016/j.matlet.2008.06.028 ↗
21. X. Gao, S.M. Zhu, B. C. Muddle, J. F. Nie: Scripta Mater, 2005, vol. 53, pp. 1321-1326.10.1016/j.scriptamat.2005.08.035 ↗
22. J. F. Nie, B. C. Muddle: Scripta Mater, 1997, vol. 37, pp. 1475-1481.10.1016/S1359-6462(97)00294-7 ↗
23. Y. Wan, G. Xiong, H. Luo, F. He, Y. Huang and X. Zhou: Mater. Design., 2008, vol. 29, pp. 2034-37.10.1016/j.matdes.2008.04.017 ↗
24. H.Y. Tok, E. Hamzah, and H.R. Bakhsheshi-Rad: J. Alloy. Compd., 2015, vol. 640, pp. 335-46.10.1016/j.jallcom.2015.03.217 ↗
25. M. Easton, J. Grandfield, D. StJohn and B. Rinderer: Mater. Sci. Forum., 2006, vol. 519-521, pp. 1675-80.10.4028/www.scientific.net/MSF.519-521.1675 ↗
26. M. Easton, H. Wang, J. Grandfield, D. StJohn and E. Sweet: Mater. Forum.,, 2004, vol. 28, pp. 224-29.
27. S.M. Li, K. Sadayappan, D. Apelian: Metall. Mater. Trans. B,, 2013, vol 44, pp. 614-23.10.1007/s11663-013-9801-4 ↗
28. S. E. Harandi, M. Mirshahi, S. Koleini, M. H. Idris, H. Jafari and M. R. A. Kadir: Mater. Res., 2013, vol. 16, pp. 11-18.10.1590/S1516-14392012005000151 ↗
29. Y. C. Lee, A. K. Dahle and D. H. StJohn: Metall. Mater. Trans. A, 2000, vol. 31, pp. 2895-906.10.1007/BF02830349 ↗
30. T.W.Clyne and G.J.Davies: Brit. Foundryman, 1981, vol. 74, pp. 65-73.
31. L. Zhou, Y. D. Huang, P. L. Mao, K. U. Kainer, Z. Liu and N. Hort: Int. J. Cast. Metal. Res., 2011, vol. 24, pp. 170-76.10.1179/136404611X13001912813942 ↗
32. Z.S Zhen, N. Hort, O. Utke, Y.D. Huang, N. Petri, and K.U. Kainer: TMS, 2009, pp 105–10.
33. P. Gunde, A. Schiffl, P.J. Uggowitzer: Mater. Sci. Eng. A, 2010, vol 527, pp. 7074-79.10.1016/j.msea.2010.07.086 ↗
34. D.G. Eskin, L. Katgerman: Metall Mat Trans A, 2007, vol 38, pp. 1511-19.10.1007/s11661-007-9169-7 ↗
35. L. Sweet, M.A. Easton, J.A. Taylor, J.F. Grandfield, C.J. Davidson, L.M. Lu, M.J. Couper, and D.H. Stjohn: Metall and Mat Trans A, 2013, vol 44, pp. 5396-407.10.1007/s11661-012-1562-1 ↗
36. M. Salahshoor and Y. B. Guo: Materials, 2012, vol. 5, pp. 135-55.10.3390/ma5010135 ↗
37. I. Antoniac and M. Dinu: E-Health and Bioengineering Conference (EHB), 2011, pp. 1–4.
38. Z. J. Li, X. N. Gu, S. Q. Lou and Y. F. Zheng: Biomaterials, 2008, vol. 29, pp. 1329-44.10.1016/j.biomaterials.2007.12.021 ↗
39. Y. S. Jeong and W. J. Kim: Corros. Sci., 2014, vol. 82, pp. 392-403.10.1016/j.corsci.2014.01.041 ↗
40. J. F. Grandfield, D. G. Eskin and I. F. Brainbridge: Direct-chill casting of light alloys, Wiley, New Jersey, 2013, pp. 173-204.10.1002/9781118690734 ↗
41. Suyitno, D. G. Eskin and L. Katgerman: Mater. Sci. Eng. A, 2006, vol. 420, pp. 1-7.10.1016/j.msea.2005.12.037 ↗
42. Y. D. Huang, Z. Wang, A. Srinivasan, K. U. Kainer and N. Hort: Acta. Phys. Pol. A, 2012, vol. 122, pp. 497-500.10.12693/APhysPolA.122.497 ↗