Dynamic Strain Aging and Oxidation Effects on the Thermomechanical Fatigue Deformation of Reduced Activation Ferritic-Martensitic Steel
Source abstract
Abstract
Thermomechanical fatigue (TMF) behavior of a reduced activation ferritic-martensitic steel was investigated under in-phase (IP) and out-of-phase (OP) conditions under different mechanical strain amplitudes and temperature regimes. OP TMF was generally observed to result in the lowest cyclic lives compared to both IP TMF and isothermal low cycle fatigue (IF) at the maximum temperature (T max). The stress–strain hysteresis loops under TMF were marked by extensive serrations associated with dynamic strain aging (DSA) at the strain amplitudes of ±0.4 and ±0.6 pct. The serrations were noticed during the downward ramp of temperature that resulted in IP and OP TMF exhibiting jerky flow in the compressive and tensile portions, respectively. However, no evidence of serrated flow was seen under IF cycling at any of the temperatures within the TMF cycle. The stress response during IP TMF was marked by a near-saturation regime over 65 to 70 pct of life in contrast to continuous cyclic softening in the case of OP TMF. The marked life reduction observed under OP cycling at the strain amplitudes of ±0.4 and ±0.6 pct was attributed to the deleterious influence associated with oxidation, DSA, and tensile mean stress. The findings assume importance in the context of elevated temperature fatigue design, considering the fact that the IF data at T max are deemed adequately conservative in traditional design approaches.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High Temperature Alloys and Creep · Microstructure and Mechanical Properties of Steels · Hydrogen embrittlement and corrosion behaviors in metals
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (63)
Show source-provided references
1. Y.B. Chun, B.K. Choi, C.H. Han, D.W. Lee, S. Cho, T.K. Kim and Y.H. Jeong: Development of Reduced Activation Ferritic-Martensitic Steels in South Korea, Trans. Korean Nucl. Soc. Spring Meeting, Jeju, Korea, May 17-18, 2012.
2. K. Ehrlich: Fusion Eng. Des., 2001, vol. 56–57, pp. 71–82.10.1016/S0920-3796(01)00236-8 ↗
3. R.L. Klueh, D.S. Gelles, S. Jitsukawa, A. Kimura et al.: J. Nucl. Mater., 2002, vol. 307–11, pp. 455–65.10.1016/S0022-3115(02)01082-6 ↗
4. T. Jayakumar and E. Rajendrakumar: Fusion Eng. Des., 2014, vol. 89, pp. 1562–67.10.1016/j.fusengdes.2014.05.021 ↗
5. C. Petersen: Thermo Mechanical Fatigue Testing on EUROFER 97 and Selected Reduced Activation Ferritic Martensitic (RAFM) Steels RAFM Steels: Metallurgical and Mechanical Characterisation, Final Report for Task TW2-TTMS-002-D19, Forschungszentrum Karlsruhe GmbH, Karlsruhe (2009).
6. C.E. Jaske: in Thermal Fatigue of Materials and Components, ASTM STP 612, D.A. Spera and D.F. Mowbray, eds., American Society for Testing and Materials, Philadelphia, 1976, pp. 170–98.
7. M.L. Karasek, H. Sehitoglu and D.C. Slavik: in Low Cycle Fatigue, ASTM STP 942, H.D. Solomon, G.R. Halford, L.R. Kaisand and B.N. Leis eds., American Society for Testing and Materials 1988 pp. 184–205.10.1520/STP24483S ↗
8. C. Petersen and D. Rodrian: Int. J. Fatigue, 2008, vol. 30, pp. 339–44.10.1016/j.ijfatigue.2007.01.053 ↗
9. C. Petersen and D. Rodrian: J. Nucl. Mater., 2002, vol. 307–311, pp. 500–04.10.1016/S0022-3115(02)01084-X ↗
10. J. Aktaa, M. Klotz and C. Petersen: J. Nucl. Mater., 2007, vol. 367-370, pp. 550–55.10.1016/j.jnucmat.2007.03.237 ↗
11. J. Aktaa, M. Weick and M. Walter: High Temperature Creep–Fatigue Structural Design Criteria for Fusion Components Built from EUROFER 97, Final Report: TW2–TTMS–005b, D1 TW5–TTMS–005, D7, Forschungszentrum Karlsruhe GmbH, Karlsruhe (2007).
12. A. Nagesha, R. Kannan, G.V.S. Sastry, R. Sandhya, Vakil Singh, K. Bhanu Sankara Rao and M.D. Mathew: Mater. Sci. Eng. A, 2012, vol. 554, pp. 95-104.10.1016/j.msea.2012.06.021 ↗
13. A. Nagesha, R. Kannan, V.S. Srinivasan, P. Parameswaran, R. Sandhya, B.K. Choudhary, M.D. Mathew, T. Jayakumar, and E. Rajendra Kumar: Proc. Eng., 2014, vol. 86, pp. 88–94.10.1016/j.proeng.2014.11.015 ↗
14. A. Marek, G. Junak, J. Okrajni: Archiv. Mater. Sci. Eng., 2009, vol. 40 (1), pp. 37-40.
15. Y.–J. Oh, W.–J. Yang, J.–G. Jung and W.–D. Choi: Int. J. Fatigue, 2012, vol. 40, pp. 36–42.10.1016/j.ijfatigue.2012.01.013 ↗
16. M.G. Castelli and J.R. Ellis: in Thermomechanical Fatigue Behaviour of Materials ASTM STP 1186, H. Sehitoglu, ed., American Society for Testing and Materials, Philadelphia, 1993, pp. 195–211.10.1520/STP24257S ↗
17. S. Kim and J.R. Weertman: Metall. Trans. A, 1988, vol. 19, pp. 999–1007.10.1007/BF02628384 ↗
18. B. Fournier, M. Sauzay C. Caës, M. Noblecourt, M. Mottot, A. Bougault, V. Rabeau and A. Pineau: Int. J. Fatigue, 2008, vol. 30, pp. 663-76.10.1016/j.ijfatigue.2007.05.008 ↗
19. W.B. Jones: Proc. ASM Int Conf on Production, Fabrication, Properties and Application of Ferritic Steels for High Temperature Applications, A.K. Khare, ed., Warren, 1981, pp. 221–35.
20. A. Nagesha, M. Valsan, R. Kannan, K. Bhanu Sankara Rao K and S.L. Mannan: Int. J. Fatigue, 2002, vol. 24, pp. 1285-93.10.1016/S0142-1123(02)00035-X ↗
21. A.F. Armas, C. Petersen, R. Schmitt, M. Avalos and I. Alvarez-Armas: J. Nucl. Mater., 2002, vol. 307–311, pp. 509-13.10.1016/S0022-3115(02)01086-3 ↗
22. A.F. Armas, C. Petersen, R. Schmitt, M. Avalos and I. Alvarez: J. Nucl. Mater., 2004, vol. 329–333, pp. 252-60.10.1016/j.jnucmat.2004.04.045 ↗
23. K. Mariappan, Vani Shankar, R. Sandhya, G.V. Prasad Reddy, M.D. Mathew: J. Nucl. Mater., 2013, vol. 435, pp. 207–13.10.1016/j.jnucmat.2012.12.049 ↗
24. G.V.P Reddy, R. Sandhya, K. Laha and M.D. Mathew: Mater. Sci. Eng. A, 2010, vol. 527 (23), pp. 6449–53.10.1016/j.msea.2010.06.048 ↗
25. Vani Shankar, K. Mariappan, A. Nagesha, G.V.P. Reddy, R. Sandhya, M.D. Mathew and T. Jayakumar: Fusion. Eng. Des., 2012, vol. 87 (4), pp. 318-24.10.1016/j.fusengdes.2012.01.020 ↗
26. Vani Shankar, M. Valsan, K. Bhanu Sankara Rao, R. Kannan, S.L. Mannan, S.D. Pathak: Mater. Sci. Eng. A, 2006, vol. 437, pp. 413–22.10.1016/j.msea.2006.07.146 ↗
27. M. Schutze: Mater. High Temp., 2005, vol. 22 (1-2), pp. 147-54.10.1179/mht.2005.017 ↗
28. J. Aktaa and R. Schmitt: Fusion Eng. Des., 2006, vol. 81, pp. 2221-31.10.1016/j.fusengdes.2006.03.002 ↗
29. Vani Shankar, V. Bauer, R. Sandhya, M.D. Mathew and H. -J. Christ: J. Nucl. Mater., 2012, vol. 420 (1–3), pp. 23–30.10.1016/j.jnucmat.2011.08.048 ↗
30. M. Fujino and S. Taira: ICM 3, vol. 2, (1979), pp. 49–58.10.1016/B978-1-4832-8414-9.50030-4 ↗
31. E.G. Ellison and A. Al-Zamily: Fatigue Fract. Eng. Mater. Struct. 1994, vol. 17(1), pp. 39–51.10.1111/j.1460-2695.1994.tb00771.x ↗
32. R. Zauter, H. -J. Christ and H. Mughrabi: Metall. Mater. Trans. A, 1994, vol. 25, pp. 401-06.10.1007/BF02647985 ↗
33. A. Nagesha, M. Valsan, R. Kannan, K. Bhanu Sankara Rao, V. Bauer, H.J. Christ and Vakil Singh: Int. J. Fatigue, 2009, vol. 31, pp. 636-43.10.1016/j.ijfatigue.2008.03.019 ↗
34. G.V.P. Reddy, A. Nagesha, R. Sandhya, S. Sankaran, M.D. Mathew and K. B.S. Rao: Metall. Mater. Trans. A, 2015, vol. 46A, pp. 695–707.10.1007/s11661-014-2653-y ↗
35. V.S. Srinivasan, A. Nagesha, M. Valsan, K.B.S. Rao, S.L. Mannan and D.H. Sastry: Int. J. Press. Vess. Pip., 1999, vol. 76, pp. 863–70.10.1016/S0308-0161(99)00023-X ↗
36. H.E. Evans: in Interfacial Crack Growth During Temperature Changes, in: Cyclic Oxidation of High Temperature Materials, M. Schutze and W.J. Quadakkers eds., Frankfurt, vol. 27, 1999, pp. 3–16.10.1201/9781003580041-2 ↗
37. D. Laverde, T. Gómez-Acebo and F. Castro: Corr. Sci., 2004, vol. 46, pp. 613–31.10.1016/S0010-938X(03)00173-2 ↗
38. M.E. Manning: Corr. Sci., 1981, vol. 21 (4), pp. 301-16.10.1016/0010-938X(81)90005-6 ↗
39. S. Rajendran Pillai, P. Shankar, and H.S. Khatak: High Temp. Mater. Proc., 2004, vol. 23, pp. 195–204.10.1515/HTMP.2004.23.3.195 ↗
40. H.-J. Christ: Mater. Sci. Eng. A, 2007, vol. 468-470, pp. 98-108.10.1016/j.msea.2006.08.132 ↗
41. B.K. Choudhary: Mater. Sci. Eng. A, 2013, vol. 564, pp. 303–09.10.1016/j.msea.2012.11.104 ↗
42. B.K. Choudhary, V.S. Srinivasan and M.D. Mathew: Mater. High Temp., 2011, vol. 28 (2), pp. 155–61.10.1179/096034011X13072941275843 ↗
43. A. Sarkar, S.A. Maloy and K.L. Murty: Mater. Sci. Eng. A, 2015, vol. 631, pp. 120–25.10.1016/j.msea.2015.02.022 ↗
44. R. Kishore, R.N. Singh, T.K. Sinha and B.P. Kashyap: J. Mater. Sci., 1997, vol. 32, pp. 437–42.10.1023/A:1018569803900 ↗
45. Preeti Verma, G. Sudhakar Rao, P. Chellapandi, G.S. Mahobia, K. Chattopadhyay, N.C. Santhi Srinivas and Vakil Singh: Mater. Sci. Eng. A, 2015, vol. 621, pp. 39–51.10.1016/j.msea.2014.10.011 ↗
46. B.K. Choudhary, E. Isaac Samuel, G. Sainath, J. Christopher and M.D. Mathew: Metall. Mater. Trans. A, 2013, vol. 44, pp. 4979–92.10.1007/s11661-013-1869-6 ↗
47. C. Keller, M.M. Margulies and I. Guillot: Mater. Sci. Eng. A, 2012, vol. 536, pp. 273–75.10.1016/j.msea.2011.12.031 ↗
48. A.F. Armas, M. Avalos, I. Alvarez–Armas, C. Petersen and R. Schmitt: J. Nucl. Mater., 1998, vol. 258–263, pp. 1204–08.10.1016/S0022-3115(98)00187-1 ↗
49. H. Li, A. Nishimura, Z. Li, T. Nagasaka and T. Muroga: Fusion Eng. Des., 2006, vol. 81, pp. 241–45.10.1016/j.fusengdes.2005.08.050 ↗
50. H. Li, A. Nishimura, T. Nagasaka and T. Muroga: Fusion Eng. Des., 2006, vol. 81, pp. 2907–12.10.1016/j.fusengdes.2006.07.055 ↗
51. X. Hu, L. Huang, W. Yan, W. Wang, W. Sha, Y. Shan and K. Yang: Mater. Sci. Eng. A, 2014, vol. 613, pp. 404–13.10.1016/j.msea.2014.06.069 ↗
52. J. Vanaja, K. Laha, Shiju Sam, M. Nandagopal, S. Panneer Selvi, M.D. Mathew, T. Jayakumar and E. Rajendra Kumar: J. Nucl. Mater., 2013, vol. 424, pp. 116–22.10.1016/j.jnucmat.2012.02.020 ↗
53. V.S. Srinivasan, R. Sandhya, K. Bhanu Sankara Rao, S.L. Mannan and K.S. Raghavan: Int. J. Fatigue, 1991, vol. 13 (6), pp. 471–78.10.1016/0142-1123(91)90482-E ↗
54. S. -G. Hong and S. -B. Lee: J. Nucl. Mater., 2005, vol. 340, pp. 307–14.10.1016/j.jnucmat.2004.12.012 ↗
55. K.B.S. Rao, M. Valsan, R. Sandhya, S.L. Mannan, and P. Rodriguez: High Temp. Mater. Proc., 1986, vol. 7, pp. 171–77.10.1515/HTMP.1986.7.2-3.171 ↗
56. P. Rodriguez: Bull. Mater. Sci., 1984, vol. 6, pp. 653-63.10.1007/BF02743993 ↗
57. H. Jiang, Q. Zhang, X. Chen, Z. Chen, Z. Jiang, X. Wu and J. Fan: Acta Mater., 2007, vol. 55, pp. 2219-28.10.1016/j.actamat.2006.10.029 ↗
58. W. Charnock: Philos. Mag., 1969, vol. 20, p. 427.10.1080/14786436908228714 ↗
59. E. Pink: Acta Mater., 1989, vol. 37, pp. 1773-81.10.1016/0001-6160(89)90062-X ↗
60. K. Tsuzaki, T. Hori, T. Maki and I. Tamura: Mater. Sci. Eng., 1983, vol. 61, pp. 247-60.10.1016/0025-5416(83)90107-6 ↗
61. Y. Estrin and L.P. Kubin: Continuum Models for Materials with Microstructure, ed. Muhlhaus, New York, Wiley, 1995, pp. 395–450.
62. R. Abbaschian, L. Abbaschian and R. E. Reed-Hill: Physical Metallurgy Principles, Cengage Learning, 2009.
63. R.E. Smallman and R.J. Bishop: Modern Physical Metallurgy and Materials Engineering Science, Process, Applications, Sixth Edition, Butterworth-Heinemann, 1999.