The Nature of Tensile Ductility as Controlled by Extreme-Sized Pores in Powder Metallurgy Ti-6Al-4V Alloy
Source abstract
Abstract
Tensile properties of Ti-6Al-4V titanium alloy, sintered by a new process (sintering, phase transformation, and dehydrogenation of titanium hydride compacts, termed HSPT process), were investigated to determine how the sintering pores influence the tensile strength and ductility. It was found that the ductility in the sintered alloy is severely affected by the size of the largest pore, referred here as extreme-sized pore, even when the average volume fraction of porosity is nearly constant between a large number of samples. It is shown that the rapid decrease in ductility, with an increase in the extreme pore size, is caused by strain localization around the extreme-sized pore and early crack initiation. This crack initiation leads to fracture of the plane containing the pore thereby limiting the extent of uniform plastic strain that can be attained before fracture. Interestingly, the strength properties are, however, found to be independent of the size of the extreme-sized pore. The results are explained on the basis of stress concentration and strain localization around the extreme-sized pores. The work also reveals that if the extreme-sized pores are eliminated, PM Ti-6Al-4V alloy with high strength (~1100 MPa) and good ductility (~12 pct), which is easily comparable to a wrought Ti-6Al-4V alloy, can be achieved even at oxygen levels up to 0.4 wt pct.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Powder Metallurgy Techniques and Materials · Advanced materials and composites · Titanium Alloys Microstructure and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (41)
Show source-provided references
1. F.H. Froes, S.J. Mashl, V.S. Moxson, J.C. Hebeisen and V.A. Duz: JOM, 2004, vol. 56, pp. 46-48.10.1007/s11837-004-0252-x ↗
2. F.H. Froes and C. Suryanarayana: Rev. in Particulate Mater., 1933, vol. 1, pp. 233-275.
3. F. H. Froes and D. Eylon: Int. Mater. Rev., 1990, vol. 35, pp. 162-182.10.1179/095066090790323984 ↗
4. V.A.R. Henriques, C. A. A. Cairo and J.C. Bressian: Mater. Research, 2005, vol. 8, pp. 443-446.10.1590/S1516-14392005000400015 ↗
5. C. H. Caceres: Scrip. Metall. Mater., 1995, vol. 32, pp. 1851-1856.10.1016/0956-716X(95)00031-P ↗
6. Y. Liu, L.F. Chen, H.P. Tang, C.T. Liu, B. Liu and B.Y.Huang: Mat. Sci. Eng. A, 2006, vol. 418A, pp. 25-35.10.1016/j.msea.2005.10.057 ↗
7. M. Hagiwara, Y. Kaieda, Y. Kawabe and S. Miura: ISIJ Int., 1991, vol. 31, pp. 922-930.10.2355/isijinternational.31.922 ↗
8. O.M. Ivasishin, D.G. Savvakin, F. Froes, V.C. Mokson and K.A. Bondareva: Powder Metall. Met. Ceram. 2002, vol. 41, pp. 382-390.10.1023/A:1021117126537 ↗
9. A. Carman, L.C. Zhang, O.M. Ivasishin, D.G. Savvakin, M.V. Matviychuk and E.V. Pareloma: Mater. Sci. Eng. A, 2011, vol. 528, pp. 1686-1693.10.1016/j.msea.2010.11.004 ↗
10. O. M. Ivasishin and D.G. Savvakin: Key Eng. Mat., 2010, vol. 436, pp. 113-121.10.4028/www.scientific.net/KEM.436.113 ↗
11. O.M. Ivasishin, D.G. Savvakin, M.M. Gumenyak and O.B. Bondarchuk: Key Eng. Mat., 2012, vol. 520, pp. 121-132.10.4028/www.scientific.net/KEM.520.121 ↗
12. W.R. Kerr: Metall. Trans. A, 1985, vol. 16, pp. 1077-1087.10.1007/BF02811677 ↗
13. D.H. Kohn and P. Ducheyne: J. Mater. Sci., 1991, vol. 26, pp. 534-544.10.1007/BF00576555 ↗
14. W.R. Kerr, P.R. Smith, M.E. Rosenblum, F.J. Gurney, Y.R. Mahajan, and L.R. Bidwell: Titanium’80, Science and Technology, Proceedings of the 4 th International Conference on Titanium, Metall. Soc. AIME. Kyoto, Japan, 1980, pp. 2477–86.
15. W.H. Kao, D. Eylon, C.F. Yolton, F.H. Froes: Prog. Powder Metall. 1981, vol. 37, pp. 289–301.
16. F.H. Froes, O.N. Senkov, J.I. Qazi: Int. Mater. Rev., 2004, vol. 49, pp. 227–245.10.1179/095066004225010550 ↗
17. Z. Z Fang, P. Sun and H. Wang: Adv. Eng. Mat., 2012, vol. 14, pp. 383-387.10.1002/adem.201100269 ↗
18. B. Hariprasad, T.H. Courtney and J.K. Lee: Metall. Trans. A, 1988, vol. 19A, pp. 517-526.10.1007/BF02649266 ↗
19. R.J. Bourcier, D.A.Koss, R.E. Smelser and O. Richmond: Acta Metall., 1986, vol. 34, pp. 2443-2453.10.1016/0001-6160(86)90147-1 ↗
20. A.M. Gokhale and G. R. patel: Scripta Mater., 2005, vol. 52, pp. 237-241.10.1016/j.scriptamat.2004.09.011 ↗
21. D. Bozic, D.Sekulic, J.Stasic, V. Rajkovic, and M. T. Jovanovic: Inter. J. Mater. Res., 2008, vol. 99, pp. 1268-1274.10.3139/146.101762 ↗
22. H. Wang, Z.Z. Fang and P. Sun: Inter. J. powder metal., 2010, vol. 46, pp. 45-57.
23. H. Mae, X. Teng, Y. Bai and T. Wierzbicki: J. Sol. Mech. Mater. Eng., 2008, vol. 2, pp. 924-942.10.1299/jmmp.2.924 ↗
24. R.J. Shore and R.B. McCauley: Weld Research supplement, 51st Annual Meeting, Cleveland, OH. June 8-12, 1970. pp. 311s-21s.
25. M. K. Surappa, E. Blank and J. C. Jaquet: Scripta Met., 1986, vol. 20, pp. 1281-1286.10.1016/0036-9748(86)90049-9 ↗
26. P. Sun, Z. Z. Fang and M. Koopman: Adv. Eng. Mat., 2013, vol. 15, pp. 1007-1013.10.1002/adem.201300017 ↗
27. J. D. Paramore, Z. Z. Fang, P. Sun, M. Koopman, K.S. Ravi Chandran and M. Dunstan: Scripta Mater., 2015, vol. 107, pp. 103-106.10.1016/j.scriptamat.2015.05.032 ↗
28. P. Sun, Z.Z. fang, M. Koopman, Y. Xia, J. paramour, K.S. Ravi Chandran, Y. Ran and J. Lu: Metall. Mater. Trans. A, 2015, vol. 46A, pp. 5546-5560.10.1007/s11661-015-3141-8 ↗
29. K.S. Ravi Chandran and A.K. Vasudeven: Fatigue and Fracture, ASM International, Materials Park, OH, 1996, pp. 381-92.10.31399/asm.hb.v19.a0002379 ↗
30. S.H. Teoh, R. Thampuran, W.K.H. Seah and J.C.H. Goh: Biomaterials, 1993, Vol. 14, pp. 407-412.10.1016/0142-9612(93)90142-O ↗
31. N.R. Moody, W.M. Garrison Jr., J.E. Smugeresky and J.E. Costa, Metall. Trans. A, 1993, vol. 24A, pp. 161-174.10.1007/BF02669613 ↗
32. Y. Yan, G.L. Nash and P. Nash: Int. J. Fatigue, 2013, vol. 55, pp. 81-91.10.1016/j.ijfatigue.2013.05.015 ↗
33. G. W. Mugica, D. O. Tovio, J. C. Cuyas and A. C. Gonzalez: Mater. Reseach, 2004, vol. 7, pp. 221-229.10.1590/S1516-14392004000200002 ↗
34. F. Cao, P. Kumar, M. Koopman, C. Lin, Z.Z. Fang and K.S. Ravi Chandran: Mater. Sci. Eng. A, 2015, vol. 630A, pp. 139-145.10.1016/j.msea.2015.02.028 ↗
35. Y. Itoh, T. Uematsu, K. Sato, H. Miura: J. Jpn. Soc. Powder Powder Metall., 2009, vol. 56, pp. 259-263.10.2497/jjspm.56.259 ↗
36. P. Kumar, K.S. Ravi Chandran, F. Cao, P. Sun, M. Koopman, and Z. Zak Fang: Titanium-2015, Science and Technology, 13th world Conference on Titanium, TMS. San Diego, CA, August 16-20, 2015.
37. G.R. Irvin: J. Appl. Mech., 1962, vol. 29, pp. 651-654.10.1115/1.3640649 ↗
38. N. Chawla, X. Deng: mater. Sci. Eng. A, 2005, vol. 390, pp. 98-112.10.1016/j.msea.2004.08.046 ↗
39. S. J. Polasik, J.J. Williams, N. Chawla: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 73-81.10.1007/s11661-002-0006-8 ↗
40. A. Hardrboletz, B. Weiss: Int. mater. Rev., 1997, vol. 42, pp. 1-44.10.1179/imr.1997.42.1.1 ↗
41. C.H. Caceres, B.I. Selling, Mater. Sci. Eng. A, 1996, vol. 220, pp. 109-116.10.1016/S0921-5093(96)10433-0 ↗