journal article·2011-09

Cyclic Deformation Response of β-Annealed Ti-5Al-5V-5Mo-3Cr Alloy Under Compressive Loading Conditions

Jun Huang, Zhirui Wang, Jie Zhou

Publisher page

Abstract

This article reports the cyclic deformation behavior of the β-annealed metastable Ti-5Al-5V-5Mo-3Cr (Ti-5553) alloy under the condition of pure compressive fatigue stress. The following three aspects, namely, the mechanical response, the surface morphology evolution, and the dislocation structures, were systematically investigated. Under all testing conditions, the material demonstrated cyclic softening in the initial cycles followed by saturation. The progressive observation of surface morphology at fixed locations, but after different numbers of cycles, elucidated typical planar slip behavior and the early appearance of fatigue microcracks, which were found often to be induced by the highly localized planar slip bands. The transmission electron microscopy (TEM) study revealed dislocation annihilation upon cycling, i.e., the reduction of dislocation density as well as the simplification of dislocation configurations. In addition, detwinning and changed twin boundary structures upon cycling were also detected. Such activities, together with the intersection of coherent ω precipitates by moving dislocations, are considered to be responsible for the initial softening, whereas the dislocation dipole flip-flop mechanism is presumably responsible for the cyclic saturation behavior. An attempt was made to explain the strain-localized planar slip behavior by considering the stacking fault energy (SFE) as well as the free-electron-to-atom (e/a) ratio. The nanoscaled ω and α precipitation in the β matrix may also contribute to the planar slip behavior. The effect of the microstructure in the as-received material was also analyzed for the strain localization and planar-slip mode.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Titanium Alloys Microstructure and Properties · Metal and Thin Film Mechanics · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (49)

Show source-provided references
1. N.G. Jones, R.J. Dashwood, M. Jackson, and D. Dye: Acta Mater., 2009, vol. 57, pp. 3830–39.10.1016/j.actamat.2009.04.031 ↗
2. A.F. Gerday, M. Ben Bettaieb, L. Duchêne, N. Clément, H. Diarra, and A.M. Habraken: Acta Mater., 2009, vol. 57, pp. 5186–95.10.1016/j.actamat.2009.07.020 ↗
3. N.G. Jones, R.J. Dashwood, D. Dye, and M. Jackson: Metall. Mater. Trans. A, 2009, vol. 40A, pp. 1944–54.10.1007/s11661-009-9866-5 ↗
4. S. Veeck, D. Lee, R. Boyer, and R. Briggs: Adv. Mater. Process., 2004, vol. 10, pp. 47–49.
5. S. Nag, R. Banerjee, R. Srinivasan, J.Y. Hwang, M. Harper, and H.L. Fraser: Acta Mater., 2009, vol. 57, pp. 2136–47.10.1016/j.actamat.2009.01.007 ↗
6. S. Nag, R. Banerjee, J.Y. Hwang, M. Harper, and H.L. Fraser: Phil. Mag., 2009, vol. 89, pp. 535–52.10.1080/14786430802613158 ↗
7. J.D. Cotton, R.R. Boyer, R.D. Briggs, R.G. Baggerly, C.A. Meyer, and M.D. Carter: in Ti-2007: Science and Technology, M. Ninomi, S. Akiyama, M. Ikeda, M. Hagiwara, and K. Maruyama, eds., The Japan Institute of Metals, Kyoto, 2007, pp. 471–74.
8. M.L. Harper: M.Sc. Thesis, The Ohio State University, Columbus, OH, 2004.
9. R. Panza-Giosa, Z. Wang, and D. Embury: Mechanical Properties and Microstructural Evolution of Ti-5Al-5V-5Mo-3Cr Alloy, Toronto, unpublished research, 2009.
10. G. Theodorski and D.A. Koss: Titanium and Titanium Alloys: Scientific and Technological Aspects, Proc. 3rd Int. Conf. on Titanium, Moscow, May 18–21, 1976, J.C. Williams and A.F. Belov, eds., Plenum Press, New York, NY, 1982, pp. 553–67.
11. D.A. Koss and C.C. Wojcik: Metall. Trans. A, 1976, vol. 7A, pp. 1243–44.10.1007/BF02656613 ↗
12. S.B. Chakrabortty, T.K. Mukhopodhyay, and E.A. Starke: Acta Metall., 1978, vol. 26, pp. 909–20.10.1016/0001-6160(78)90042-1 ↗
13. Y. Saleh and H. Margolin: Metall. Trans. A, 1980, vol. 11A, pp. 1295–1302.10.1007/BF02653483 ↗
14. C. Calabrese and C. Laird: Mater. Sci. Eng., 1974, vol. 13, pp. 141–59.10.1016/0025-5416(74)90182-7 ↗
15. J. Polák, T. Lepistö, and P. Kettunen: Mater. Sci. Eng., 1985, vol. 74, pp. 85–91.10.1016/0025-5416(85)90112-0 ↗
16. J. Polάk, M. Petrenec, and J. Man: Mater. Sci. Eng. A, 2005, vols. 400–401, pp. 405–08.10.1016/j.msea.2005.01.064 ↗
17. J. Polάk, K. Obrtllík, and P. Liškutín: in Basic Mechanisms in Fatigue of Metals, P. Lukάš and J. Polάk, eds., Academia and Elsevier, Prague, 1988, pp. 101–09.
18. J. Polάk and M. Klesnil: in Fracture Control of Engineering Structures, H.C. Van Elst and A. Bakker, eds., EMAS, London, 1986, vol. 3, pp. 1559–68.
19. J.A. Robertson, S. Fujishiro, V.S. Arunachalam, and C.M. Sargent: Metall. Trans., 1974, vol. 5, pp. 2317–22.10.1007/BF02644012 ↗
20. T.S. Kuan, R.R. Ahrens, and S.L. Sass: Metall. Trans. A, 1975, vol. 6A, pp. 1767–74.10.1007/BF02642306 ↗
21. T. Furuhara, K. Kishimoto, and T. Maki: Mater. Trans. JIM, 1994, vol. 35 (12), pp. 843–50.10.2320/matertrans1989.35.843 ↗
22. O.A. Yelkina and R.M. Lerinman: Phys. Met. Metallogr., 1979, vol. 45, pp. 78–83.
23. T. Grosdidier, C. Rouhaud, M.-J. Philippe, and Y. Combres: Scripta Mater., 1997, vol. 36, pp. 21–28.10.1016/S1359-6462(96)00341-7 ↗
24. P.R. Thornton, T.E. Mitchell, and P.B. Hirsch: Phil. Mag., 1962, vol. 7, pp. 1349–69.10.1080/14786436208213168 ↗
25. S. Hanada, T. Yoshio, K. Nishimura, and O. Izumi: Titanium ‘88: Science and Technology, Proc. 6th World Conf. on Titanium, 1988, pp. 105–10.
26. H.G. Paris, B.G. Lefevre, and E.A. Starke, Jr.: Metall. Trans. A, 1976, vol. 7A, pp. 273–78.10.1007/BF02644467 ↗
27. H. Xing and J. Sun: Appl. Phys. Lett., 2008, vol. 93 (3), p. 031908.10.1063/1.2959183 ↗
28. Y. Yang, G.P. Li, G.M. Cheng, Y.L. Li, and K. Yang: Appl. Phys. Lett., 2009, vol. 94 (6), p. 061901.10.1063/1.3078521 ↗
29. L. Rémy: Metall. Trans. A, 1981, vol. 12A, pp. 387–408.10.1007/BF02648536 ↗
30. A. Gemperle, N. Zárubová, and J. Gemperlová: J. Mater. Sci., 2005, vol. 40, pp. 3247–54.10.1007/s10853-005-2693-1 ↗
31. S.M. Yin, F. Yang, X.M. Yang, S.D. Wu, S.X. Li, and G.Y. Li: Mater. Sci. Eng. A, 2008, vol. 494, pp. 397–400.10.1016/j.msea.2008.04.056 ↗
32. Y. Liu: Proc. IUTAM Symp. on Mechanics of Martensitic Phase Transformation in Solids, Q.P. Sun, ed., Kluwer Academic Publisher, Dordrecht, ISBN 1-4020-0741-8, 2002, pp. 37–44.10.1007/978-94-017-0069-6_5 ↗
33. C.E. Feltner: Phil. Mag., 1965, vol. 12, pp. 1229–48.10.1080/14786436508228673 ↗
34. Z. Wang: Phil. Mag., 2004, vol. 84, pp. 351–79.10.1080/14786430310001639824 ↗
35. H. Mughrabi: Mater. Sci. Eng., 1978, vol. 33, pp. 207–23.10.1016/0025-5416(78)90174-X ↗
36. B. Gong, Z. Wang, and Z.G. Wang: Acta Metall., 1999, vol. 47, pp. 307–15.
37. M.A. Meyers and K.K. Chawla: Mechanical Behaviour of Materials, Prentice-Hall, Upper Saddle River, NJ, 1992, p. 295
38. Mechanical Metallurgy-Principles and Applications, Prentice-Hall, Englewood Cliffs, NJ, 1999, p. 217.
39. H.P. Karnthaler and M. Schugerl: Strength of Metals and Alloys, Pergamon, Oxford, United Kingdom, 1979, pp. 205–10.10.1016/B978-1-4832-8412-5.50042-4 ↗
40. V. Gerold and H. P. Karnthaler: Acta Metall. Mater., 1989, vol. 37, pp. 2177–83.10.1016/0001-6160(89)90143-0 ↗
41. A. De Crecy, A. Bourret, S. Naka, and A. Lasalmonie: Phil. Mag. A, 1983, vol. 47, pp. 245–54.10.1080/01418618308245221 ↗
42. K.S. Chan, J.W. Tian, B. Yang, and P.K. Liaw: Metall. Mater. Trans. A, 2009, vol. 40A, pp. 2545–56.10.1007/s11661-009-9980-4 ↗
43. T. Onchi, H. Kayano, and Y. Higashiguchi: J. Nucl. Mater., 1980, vol. 88, pp. 226–35.10.1016/0022-3115(80)90278-0 ↗
44. S.I. Hong and C. Laird: Acta Metall., 1990, vol. 38, pp. 1581–94; Mater. Sci. Eng., 1990, vol. 124, pp. 183–201; Acta Metall., 1990, vol. 38, pp. 2085–2100.10.1016/0956-7151(90)90126-2 ↗
45. L.M. Brown: Proc. Int. Conf. Dislocation Modeling of Physical Systems, M.F. Ashby, R. Bullough, C.S. Harley, and J.P. Hirth, eds., EMAS, London, 1986, vol. 3, p. 1559.
46. H. Mughrabi: Acta Metall., 1983, vol. 31, pp. 1367–79.10.1016/0001-6160(83)90007-X ↗
47. U. Essmann, U. Gősele, and H. Mughrabi: Phil. Mag. A, 1981, vol. 44, pp. 405–26.10.1080/01418618108239541 ↗
48. J. Polάk: Mater. Sci. Eng., 1987, vol. 92, pp. 71–80.10.1016/0025-5416(87)90157-1 ↗
49. S. Suresh: Fatigue of Materials, Cambridge University Press, New York, NY, 1991, p. 44.