Formability of Ultrafine-Grained Interstitial-Free Steels
Source abstract
Abstract
The stretch formability of ultrafine-grained (UFG) interstitial-free steel (IF-steel) produced by equal-channel angular extrusion/pressing (ECAE/P) via various strain paths was investigated with a miniaturized Erichsen test. A coarse-grained (CG) sample demonstrated high formability with an Erichsen index (EI) of 4.5 mm. Grain refinement by ECAE decreased the formability, but increased the required punch load (FEI) depending on the applied strain paths. The EI values were 0.35, 2.90, and 3.91 mm for 8A-, 8Bc-, and 8C-processed samples, respectively. Decrease in the biaxial stretch formability was attributed to the limited strain-hardening capacity of the UFG microstructure. Also, the grain morphology of the UFG microstructure was found to be very influential on stretch formability. Heavily elongated grain morphology in the 8A-processed microstructure resulted in the lowest formability due to the increased cracking tendency through elongated grain boundaries. However, the UFG microstructures with equiaxed grains obtained after 8C and 8Bc ECAE resulted in better formability compared to 8A. The UFG microstructure reduced the roughness (orange peel effect) of the free surface of the biaxial stretched samples by decreasing the non-uniform grain flow leading to the so-called orange peel effect. It should be noted that the strength and ductility values gained from uniaxial tensile tests are not comparable directly to the EI and FEI values determined from the Erichsen tests. Finally, it is important to emphasize that the UFG microstructure produced by a suitable strain path leading to equiaxed grains below 1 μm could be highly deformed even under multiaxial stress conditions.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and mechanical properties · Metal Forming Simulation Techniques · Metallurgy and Material Forming
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (48)
Show source-provided references
1. U. Engel and R. Eckstein: J. Mater. Process. Tech., 2002, vol. 125-126, pp. 35-44.10.1016/S0924-0136(02)00415-6 ↗
2. U. Engel, A. Rosochowski, S. Geißdörfer, and L. Olejnik: Microforming and Nanomaterials, Springer, Paris, 2007, pp. 99-124.
3. V. M. Segal: Mater. Sci. Eng. A, 2004, vol. 386, pp. 269-276.10.1016/S0921-5093(04)00934-7 ↗
4. R. Z. Valiev and T. G. Langdon: Prog. Mater. Sci., 2006, vol. 51, pp. 881-981.10.1016/j.pmatsci.2006.02.003 ↗
5. Y. T. Zhu, T. C. Lowe and T. G. Langdon: Scripta Mater., 2004, vol. 51, pp. 825-830.10.1016/j.scriptamat.2004.05.006 ↗
6. G. G. Yapici, C. N. Tome, I. J. Beyerlein, I. Karaman, S. C. Vogel and C. Liu: Acta Mater., 2009, vol. 57, pp. 4855-4865.10.1016/j.actamat.2009.06.050 ↗
7. G. G. Yapici, I. Karaman and H. J. Maier: Mater. Sci. Eng. A, 2006, vol. 434, pp. 294-302.10.1016/j.msea.2006.06.082 ↗
8. G. G. Yapici, I. J. Beyerlein, I. Karaman and C. N. Tome: Acta Mater., 2007, vol. 55, pp. 4603-4613.10.1016/j.actamat.2007.03.031 ↗
9. G. Purcek, G. G. Yapici, I. Karaman and H. J. Maier: Mater. Sci. Eng. A, 2011, vol. 528, pp. 2303-2308.10.1016/j.msea.2010.11.021 ↗
10. G. Purcek, O. Saray, O. Kul, I. Karaman, G. G. Yapici, M. Haouaoui and H. J. Maier: Mater. Sci. Eng. A, 2009, vol. 517, pp. 97-104.10.1016/j.msea.2009.03.054 ↗
11. G. Purcek, O. Saray, I. Karaman and M. Haouaoui: Metall. Mater. Trans. A, 2009, vol. 40A, pp. 2772-2783.10.1007/s11661-009-9940-z ↗
12. H. J. Maier, P. Gabor and I. Karaman: Mater. Sci. Eng. A, 2005, vol. 410, pp. 457-461.10.1016/j.msea.2005.08.079 ↗
13. I. Karaman, M. Haouaoui and H. J. Maier: J. Mater. Sci., 2007, vol. 42, pp. 1561-1576.10.1007/s10853-006-0987-6 ↗
14. H. S. Kim, M. H. Seo and S. I. Hong: J. Mater. Process. Tech., 2001, vol. 113, pp. 622-626.10.1016/S0924-0136(01)00710-5 ↗
15. M. Furukawa, Y. Iwahashi, Z. Horita, M. Nemoto and T. G. Langdon: Mater. Sci. Eng. A, 1998, vol. 257, pp. 328-332.10.1016/S0921-5093(98)00750-3 ↗
16. A. Rosochowski, W. Presz, L. Olejnik and M. Richert: Int. J. Adv. Manuf. Tech., 2007, vol. 33, pp. 137-146.10.1007/s00170-007-0955-6 ↗
17. W. Presz and A. Rosochowski: 9th Int. Conf. Mater. Form. ESAFORM 2006, A. Rosochowski and N.P. Juster, eds., Glasgow, United Kingdom, 2006, pp. 587–90.
18. X. Ma, R. Lapovok, C. Gu, A. Molotnikov, Y. Estrin, E. Pereloma, C. Davies and P. Hodgson: J. Mater. Sci., 2009, vol. 44, pp. 3807-3812.10.1007/s10853-009-3515-7 ↗
19. S. Hoile: Mater. Sci. Tech., 2000, vol. 16, pp. 1079-1093.10.1179/026708300101506902 ↗
20. K. Banerjee, A. Verma and T. Venugopalan: Metall. Mater. Trans. A, 2008, vol. 39, pp. 1410-1425.10.1007/s11661-008-9484-7 ↗
21. W. Jeong: Metall. Mater. Trans. A, 2000, vol. 31, pp. 1305-1307.10.1007/s11661-000-0125-z ↗
22. O. Saray, G. Purcek, I. Karaman, T. Neindorf and H. J. Maier: Mater. Sci. Eng. A, 2011, vol. 528, pp. 6573-6583.10.1016/j.msea.2011.05.014 ↗
23. T. Niendorf, H. J. Maier, D. Canadinc and I. Karaman: Mater. Sci. Eng. A, 2009, vol. 503, pp. 160-162.10.1016/j.msea.2008.03.054 ↗
24. T. Niendorf, D. Canadinc, H. J. Maier and I. Karaman: Int. J. Fatigue, 2008, vol. 30, pp. 426-436.10.1016/j.ijfatigue.2007.04.015 ↗
25. T. Niendorf, D. Canadinc, H. J. Maier and I. Karaman: Metall. Mater. Trans. A, 2007, vol. 38, pp. 1946-1955.10.1007/s11661-007-9154-1 ↗
26. T. Niendorf, D. Canadinc, H. J. Maier, I. Karaman and S. G. Sutter: Int. J. Mater. Res., 2006, vol. 97, pp. 1328-1336.10.3139/146.101377 ↗
27. J. De Messemaeker, B. Verlinden, and J. Van Humbeeck: Mater. Lett., 2004, vol. 58, pp. 3782-86.10.1016/j.matlet.2004.07.026 ↗
28. B. Han, F. Mohamed and E. Lavernia: Metall. Mater. Trans. A, 2003, vol. 34, pp. 71-83.10.1007/s11661-003-0209-7 ↗
29. H. S. Kim, W. S. Ryu, M. Janecek, S. C. Baik and Y. Estrin: Adv. Eng. Mater., 2005, vol. 7, pp. 43-46.10.1002/adem.200400146 ↗
30. T. Niendorf, F. Rubitschek, H. Maier, D. Canadinc and I. Karaman: J. Mater. Sci., 2010, vol. 45, pp. 4813-4821.10.1007/s10853-010-4511-7 ↗
31. G. Purcek, O. Saray, I. Karaman and T. Kucukomeroglu: Mater. Sci. Eng. A, 2008, vol. 490, pp. 403-410.10.1016/j.msea.2008.01.080 ↗
32. G. Purcek, O. Saray, I. Karaman and H. J. Maier: Metall. Mater. Trans. A, 2012, vol. 43A, pp. 1884-1894.10.1007/s11661-011-1063-7 ↗
33. R. Yoda, K. Shibata, T. Morimitsu, D. Terada and N. Tsuji: Scripta Mater., 2011, vol. 65, pp. 175-178.10.1016/j.scriptamat.2011.02.002 ↗
34. A. Sivaraman and U. Chakkingal: J. Mater. Process. Tech., 2008, vol. 202, pp. 543-548.10.1016/j.jmatprotec.2007.10.006 ↗
35. N. Hansen, X. Huang and D. A. Hughes: Mater. Sci. Eng. A, 2001, vol. 317, pp. 3-11.10.1016/S0921-5093(01)01191-1 ↗
36. D. A. Hughes, Q. Liu, D. C. Chrzan and N. Hansen: Acta Mater., 1997, vol. 45, pp. 105-112.10.1016/S1359-6454(96)00153-X ↗
37. P. C. Wu, C. P. Chang and P. W. Kao: Mater. Sci. Eng. A, 2004, vol. 374, pp. 196-203.10.1016/j.msea.2004.02.016 ↗
38. V. V. Stolyarov, Y. T. Zhu, I. V. Alexandrov, T. C. Lowe and R. Z. Valiev: Mater. Sci. Eng. A, 2001, vol. 299, pp. 59-67.10.1016/S0921-5093(00)01411-8 ↗
39. A. A. Gazder, W. Cao, C. H. J. Davies and E. V. Pereloma: Mater. Sci. Eng. A, 2008, vol. 497, pp. 341-352.10.1016/j.msea.2008.07.030 ↗
40. Y. M. Wang and E. Ma: Acta Mater., 2004, vol. 52, pp. 1699-1709.10.1016/j.actamat.2003.12.022 ↗
41. C. Y. Yu, P. W. Kao and C. P. Chang: Acta Mater., 2005, vol. 53, pp. 4019-4028.10.1016/j.actamat.2005.05.005 ↗
42. D. A. Hughes and N. Hansen: Acta Mater., 2000, vol. 48, pp. 2985-3004.10.1016/S1359-6454(00)00082-3 ↗
43. D. Shin: Met. Mater. Int., 2001, vol. 7, pp. 573-577.10.1007/BF03179256 ↗
44. C. Y. Yu, P. L. Sun, P. W. Kao and C. P. Chang: Scripta Mater., 2005, vol. 52, pp. 359-363.10.1016/j.scriptamat.2004.10.035 ↗
45. N. Krasilnikov, W. Lojkowski, Z. Pakiela and R. Valiev: Mater. Sci. Eng. A, 2005, vol. 397, pp. 330-337.10.1016/j.msea.2005.03.001 ↗
46. M. P. Manahan, A. E. Browning, A. E. Argon and O. K. Harling: Miniaturized disc bend test technique development and application, The use of small-scale specimens for testing irradiated material, ASTM, Albuquerque N.M., 1986,
47. R. Becker: Acta Mater., 1998, vol. 46, pp. 1385-1401.10.1016/S1359-6454(97)00182-1 ↗
48. O. Wouters, W.P. Vellinga, R.V. Tijum, and J.T.M. de Hosson: Acta Mater., 2005, vol. 53, pp. 4043-4050.10.1016/j.actamat.2005.05.007 ↗