Microstructures, Mechanical Properties, and Strain Hardening Behavior of an Ultrahigh Strength Dual Phase Steel Developed by Intercritical Annealing of Cold-Rolled Ferrite/Martensite
Source abstract
Abstract
A dual phase (DP) steel was produced by a new process utilizing an uncommon cold-rolling and subsequent intercritical annealing of a martensite–ferrite duplex starting structure. Ultrafine grained DP steels with an average grain size of about 2 μm and chain-networked martensite islands were achieved by short intercritical annealing of the 80 pct cold-rolled duplex microstructure. The strength of the low carbon steel with the new DP microstructure was reached about 1300 MPa (140 pct higher than that of the as-received state, e.g., 540 MPa), without loss of ductility. Tensile testing revealed good strength–elongation balance for the new DP steels (UTS × UE ≈ 11,000 to 15,000 MPa pct) in comparison with the previous works and commercially used high strength DP steels. Two strain hardening stages with comparable exponents were observed in the Holloman analysis of all DP steels. The variations of hardness, strength, elongation, and strain hardening behavior of the specimens with thermomechanical parameters were correlated to microstructural features.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Hydrogen embrittlement and corrosion behaviors in metals · Metal Alloys Wear and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (54)
Show source-provided references
1. P.C. Chakraborti and M.K. Mitra: Mater. Sci. Eng. A, 2007, vol. 466, pp. 123-33.10.1016/j.msea.2007.02.042 ↗
2. Y.L. Kang: Theory and Technology of Processing and Forming for Advanced Automobile Steel Sheets, Metallurgical Industry Press, Beijing, 2009.
3. H.F. Dong, J. Li, Y. Zhang, J. Park, and Q.X. Yang: Int. J. Miner. Metall. Mater., 2010, vol. 17, pp. 173-8.10.1007/s12613-010-0209-8 ↗
4. S. Hayami and T. Furukawa: Microalloying 75 Proceedings of the Conference, Vanitec, London, 1975, pp. 78–87.
5. J.H. Kim, M.G. Lee, D. Kim, D.K. Matlock, and R.H. Wagoner: Mater. Sci. Eng. A, 2010, vol. 527, pp. 7353-63.10.1016/j.msea.2010.07.099 ↗
6. K.S. Choi, W.N. Liu, X. Sun, and M.A. Khaleel: Metall. Mater. Trans. A, 2009, vol. 40A, pp. 796-809.10.1007/s11661-009-9792-6 ↗
7. I.B. Timokhina, E.V. Pereloma, S.P. Ringer, R.K. Zheng, and P.D. Hodgson: ISIJ Int., 2010, vol. 50, pp. 574-82.10.2355/isijinternational.50.574 ↗
8. T. Baudin, C. Quesnea, J. Jura, and R. Penelle: Mater. Charact., 2001, vol. 47, pp. 365-73.10.1016/S1044-5803(02)00183-3 ↗
9. ULSAB Advance Vehicle Concepts, Technical transfer dispatch #6, ISIJ, Brussels, May 2001.
10. C.C. Huang and H.C. Gwo: J. Mater. Sci., 1989, vol. 24, pp. 1991-4.10.1007/BF02385411 ↗
11. N. Terao and B. Cauwe: J. Mater. Sci., 1988, vol. 23, pp. 1769-78.10.1007/BF01115721 ↗
12. P. Tsipouridis, E. Werner, C. Krempaszky, and E. Tragl: Steel Res. Int., 2006, vol. 77, pp. 654-67.10.1002/srin.200606444 ↗
13. D.H. Shin, B.C. Kim, K.T. Park, and W.Y. Choo: Acta Mater., 2000, vol. 48, pp. 3245-52.10.1016/S1359-6454(00)00090-2 ↗
14. K.T. Park, Y.K. Lee, and D.H. Shin: ISIJ Int., 2005, vol. 45, pp. 750-5.10.2355/isijinternational.45.750 ↗
15. N. Tsuji: Advanced Steels: The Recent Scenario in Steel Science and Technology, Y. Weng, H. Dong, and Y. Gan, eds., Springer, New York, 2011, pp. 119–29.10.1007/978-3-642-17665-4_15 ↗
16. K. Mukherjee, S.S. Hazra, and M. Militzer: Metall. Mater. Trans. A, 2009, vol. 40A, pp. 2145-59.10.1007/s11661-009-9899-9 ↗
17. S.C. Hong and K.S. Lee: Mater. Sci. Eng. A, 2002, vol. 323A, pp. 148-59.10.1016/S0921-5093(01)01359-4 ↗
18. M. Calcagnotto, Y. Adachi, D. Ponge, and D. Raabe: Acta Mater., 2011, vol. 59, pp. 658-70.10.1016/j.actamat.2010.10.002 ↗
19. R. Song, D. Ponge, D. Raabe, and R. Kaspar: Acta Mater., 2005, vol. 53, pp. 845-58.10.1016/j.actamat.2004.10.051 ↗
20. H. Azizi-Alizamini, M. Militzer, and W.J. Poole: ISIJ Int., 2011, vol. 51, pp. 958-64.10.2355/isijinternational.51.958 ↗
21. Y. Okitsu, N. Takata, and N. Tsuji: Scripta Mater., 2009, vol. 60, pp. 76-9.10.1016/j.scriptamat.2008.09.002 ↗
22. P. Movahed, S. Kolahgar, S.P.H. Marashi, M. Pouranvari, and N. Parvin: Mater. Sci. Eng. A, 2009, vol. 518A, pp. 1-6.10.1016/j.msea.2009.05.046 ↗
23. M. Sarwar and R. Priestner: J. Mater. Sci., 1996, vol. 31, pp. 2091-5.10.1007/BF00356631 ↗
24. J. Qu, W. Dabboussi, F. Hassani, J. Nemes, and S. Yue: ISIJ Int., 2005, vol. 45, pp. 1741-6.10.2355/isijinternational.45.1741 ↗
25. S. Sodjit and V. Uthaisangsuk: Mater. Des., 2012, vol. 41, pp. 370-9.10.1016/j.matdes.2012.05.010 ↗
26. K.T. Park, S.Y. Han, B.D. Ahn, D.H. Shin, Y.K. Lee, and K.K. Um: Scripta Mater., 2004, vol. 51, pp. 909-13.10.1016/j.scriptamat.2004.06.017 ↗
27. M. Calcagnotto, D. Ponge, and D. Raabe: ISIJ Int., 2008, vol. 48, pp. 1096-101.10.2355/isijinternational.48.1096 ↗
28. T. Sakaki, K. Sugimoto, and T. Fukuzato: Acta Metall., 1983, vol. 31, pp. 1737-46.10.1016/0001-6160(83)90172-4 ↗
29. M.A. Maleque, Y.M. Poon, and H.H. Masjuki: J. Mater. Process. Technol., 2004, vol. 153, pp. 482-87.10.1016/j.jmatprotec.2004.04.391 ↗
30. A. Kumar, S.B. Singh, and K.K. Ray: Mater. Sci. Eng. A, 2008, vol. 474A, pp. 270-82.10.1016/j.msea.2007.05.007 ↗
31. Y.L. Kang, Q.H. Han, X.M. Zhao, and M.H. Cai: Mater. Des., 2013, vol. 44, pp. 331-9.10.1016/j.matdes.2012.07.068 ↗
32. J. Kadkhodapour, S. Schmauder, D. Raabe, S. Ziaei-Rad, U. Weber, and M. Calcagnotto: Acta Mater., 2011, vol. 59, pp. 4387-94.10.1016/j.actamat.2011.03.062 ↗
33. M. Calcagnotto, D. Ponge, E. Demir, and D. Raabe: Mater. Sci. Eng. A, 2010, vol. 527A, pp. 2738-46.10.1016/j.msea.2010.01.004 ↗
34. P.H. Chang and A.G. Preban: Acta Metall., 1985, vol. 33, pp. 897-902.10.1016/0001-6160(85)90114-2 ↗
35. R.G. Davies: Metall. Trans. A, 1978, vol. 9A, pp. 671-9.10.1007/BF02659924 ↗
36. M. Mazinani and W.J. Poole, Metall. Mater. Trans. A, 2007, vol. 38A, pp. 328-39.10.1007/s11661-006-9023-3 ↗
37. G.R. Spiech and R.L. Miller: Structure and Properties of Dual-Phase Steels, R.A. Kot and J.W. Morris, eds., AIME, NewYork, 1979, pp. 145–82.
38. M. Asadi, B.C. De Cooman, and H. Palkowski: Mater. Sci. Eng. A, 2012, vol. 538A, pp. 42-52.10.1016/j.msea.2012.01.010 ↗
39. A.R. Marder: Metall. Trans. A, 1981, vol. 12A, pp. 1569-79.10.1007/BF02643562 ↗
40. Z. Fan and A.P. Miodownik: Scr. Metall., 1993, vol. 28, pp. 895-900.10.1016/0956-716X(93)90052-T ↗
41. N. Nakada, Y. Arakawa, K.S. Park, T. Tsuchiyama, and S. Takaki: Mater. Sci. Eng. A, 2012, vol. 553, pp. 128-33.10.1016/j.msea.2012.06.001 ↗
42. Y.I. Son, Y.K. Lee, K.T. Park, C.S. Lee, and D.H. Shin: Acta Mater., 2005, vol. 53, pp. 3125-34.10.1016/j.actamat.2005.02.015 ↗
43. N.J. Kim and A.H. Nakagawa: Mater. Sci. Eng., 1986, vol. 83, pp. 145-9.10.1016/0025-5416(86)90181-3 ↗
44. V.C. Sangem: MSc. Thesis, University of British Columbia, Vancouver, 2012.
45. S. Sadagopan and D. Urban: Technology Roadmap Program, American Iron and Steel Institute/U.S. Department of Energy, Pittsburgh, 2003.
46. J.H. Hollomon: Trans. Metall. Soc. AIME, 1945, vol. 162, pp. 268-90.
47. M.R. Akbarpour and A. Ekrami: Mater. Sci. Eng. A, 2008, vol. 477A, pp. 306-10.10.1016/j.msea.2007.05.051 ↗
48. L.F. Ramos, D.K. Matlock, and G. Krauss: Metall. Trans. A, 1979, vol. 10A, pp. 259-61.10.1007/BF02817636 ↗
49. Z. Jiang, Z. Guan, and J. Lian: J. Mater. Sci., 1993, vol. 28, pp. 1814-8.10.1007/BF00595750 ↗
50. J. Lian, Z. Jiang, and J. Liu: Mater. Sci. Eng. A, 1991, vol. 147, pp. 55-65.10.1016/0921-5093(91)90804-V ↗
51. D.H. Shin and K.T. Park: Mater. Sci. Eng. A, 2005, vols. 410-411, pp. 299-302.10.1016/j.msea.2005.08.025 ↗
52. Y. Tomita and K. Okabayashi: Metall. Trans. A, 1985, vol. 16A, pp. 865-72.10.1007/BF02814837 ↗
53. W.R. Cribb and J.M. Rigsbee: Structure and Properties of Dual-Phase Steels, R.A. Kot and J.W. Morris, eds., AIME, New York, 1979, pp. 91–117.
54. N. Saeidi, F. Ashrafizadeh, and B. Niroumand: Mater. Sci. Eng. A, 2014, vol. 599, pp. 145-9.10.1016/j.msea.2014.01.053 ↗