journal article·2021-10

Thermal Stability of Aluminum-Nickel Binary Alloys Containing the Al-Al3Ni Eutectic

Frank Czerwinski

Publisher page

Abstract

The capability of Al–Ni binary alloys containing from 3 to 11 wt pct Ni and ranging from hypo-to hypereutectic compositions to retain strength at high temperatures was assessed through the uniaxial compression up to 500 °C and correlated with their solidification characteristics, phase composition and microstructure. The Al-Ni alloys, strengthened by the Al3Ni eutectic and proeutectic phases, at room temperature reached the yield stress of 70 to 100 MPa, being higher than 26 MPa measured for pure Al but well below 170 MPa achieved for the A380 (Al-8Si-3Cu, wt pct) alloy, tested under identical conditions. During high-temperature compression, the yield stress of Al-Ni alloys reduced at a steady rate with temperature, retaining at 400 °C and 500 °C about 50 pct and 25 pct, respectively, of its initial room temperature level. This yield stress reduction did not correlate with the low coarsening rate of Al3Ni phases and high hardness retention ratio of 75 to 80 pct, measured after 168 h heating at 500 °C. Although the higher Ni content resulted generally in the higher yield stress, the contribution of Al3Ni phases to retaining the alloy strength reduced with testing temperature; at all testing temperatures the finer Al3Ni eutectic phase was more effective than the coarser Al3Ni proeutectic phase, with an influence of the latter disappearing completely above 300 °C. An implication of the limited role of Al3Ni eutectic and proeutectic phases in room temperature strengthening of Al-Ni binary alloys and in retaining their strength at increased temperatures for development of novel aluminum alloys is discussed.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · High Temperature Alloys and Creep

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (29)

Show source-provided references
1. [2] F. Czerwinski, “Thermal stability of aluminum alloys,” Materials, vol. 13, no. 15, p. 3441, 2020.10.3390/ma13153441 ↗
2. [28] Y. Fan and M. Makhlouf, “The Al-Al3Ni eutectic reaction: crystallography and mechanism of formaion,” Met Mater Trans A, vol. 46, no. 9, pp. 3808-3812, 2015.10.1007/s11661-015-3051-9 ↗
3. [15] C. Suwanpreecha, P. Pandee, U. Patakham and C. Limmaneevichitr, “New generation of eutectic Al-Ni casting alloys for elevated temperature services,” Mater Sci Eng A, vol. 709, pp. 46-54, 2018.10.1016/j.msea.2017.10.034 ↗
4. [20] L. Pan, S. Zhang, Y. Yang, N. Gupta, C. Yang, Y. Zhao and Z. Hu, “High-temperature mechanical properties of aluminum alloy matrix composites reinforced with Zr and Ni trialumnides synthesized by in situ reaction,” Metall Mater Trans A, vol. 51, p. 214–225, 2020.10.1007/s11661-019-05511-7 ↗
5. [7] N. Belov, A. Alabin and D. Eskin, “Improving the properties of cold-rolled Al–6 pctNi sheets byalloying and heat treatment,” Scripta Mater, vol. 50, pp. 89-94, 2004.10.1016/j.scriptamat.2003.09.033 ↗
6. C. Suwanpreecha, J. Toinin, P. Pandee, D. Dunand and C. Limmaneevichitr: J. M J. Met. Mater. Miner., 2019, vol. 29, no. 2, pp. 2019-06-29.
7. [11] F. Czerwinski, “Thermal stability of Aluminum-Cerium binary alloys containing the Al-Al11Ce3 eutectic,” Mater Scie Eng A, vol. 809, p. 140973, 2021.10.1016/j.msea.2021.140973 ↗
8. M. Aniolek, T. Smith and F. Czerwinski, Combining Differential Scanning Calorimetry and Cooling-Heating Curve Thermal Analysis to study the melting and solidification behavior of Al-Ce binary alloys, Metals, vol. 11, p. 372, 2021.10.3390/met11020372 ↗
9. P. Nash, M. Singleton and J. Murray. In: Nash, P., Ed., Phase Diagrams of Binary Nickel Alloys, ASM International, Materials Park, OH, 1991.
10. [12] H. Okamoto, “Al-Ni (aluminum-nickel),” J Phs Eqil and Diff, vol. 25, p. 394, 2004.10.1007/s11669-004-0163-0 ↗
11. [13] Y. Iwasaki, Y. Katayama, S. Komatsu and H. Amano, “Equilibrium solid solubility of nickel to aluminum re-investigated by resistometry,” Journal of Japan Institute of Light Metals, vol. 57, no. 4, pp. 157-162, 2007.10.2464/jilm.57.157 ↗
12. [14] W. Fink and L. Wiley, Trans AIME, vol. 111, pp. 293-303, 1934.
13. [16] N. Belov, D. Eskin and A. Aksenov, Multicomponent Phase Diagrams: Applications for Commercial Aluminum Alloys, Amsterdam: Elsevier, 2005.
14. [17] K. Blobaum, D. Van Heerden, A. Gavens and T. Weihs, “Al/Ni formation reactions: characterization of the metastable Al9Ni2 phase and analysis of its formation,” Acta Mater, vol. 51, no. 13, pp. 3871-3884, 2003.10.1016/S1359-6454(03)00211-8 ↗
15. [26] A. Yamamoto and H. Tsubakino, “Al9Ni2 precipitates formed in an Al-Ni dilute alloy,” Scripta Mater, vol. 37, no. 11, pp. 1721-1725, 1997.10.1016/S1359-6462(97)00329-1 ↗
16. [18] A. Ustinov and S. Demchenkov, “Influence of metastable Al9Ni2 phase on the sequence of phase transformations initiated by heating of Al/Ni multilayer foils produced by EBPVD method,” Intermetallics, vol. 84, pp. 82-91, 2017.10.1016/j.intermet.2017.01.005 ↗
17. [4] P. Rohatgi and K. Prabhakar, “Wrought aluminum-nickel alloys for high strength-high conductivity applications,” Metall Mater Trans A, vol. 6, p. 1003, 1975.10.1007/BF02645524 ↗
18. K.A. Jackson, J.D. Hunt, Trans Soc Min Eng AIME 1966; 236:1129.
19. F.Z. Chrifi-Alaoui, M. Nassik, K. Mahdouk, J.C. Gachon, J. Alloys Compd., 2004, vol. 364, pp. 121-126.10.1016/S0925-8388(03)00493-6 ↗
20. [22] Z. Ding, Q. Hu and W. Lu, “Continuous morphological transition and its mechanism of Al3Ni phase at the liquid–solid interface during solidification,” Metall Mater Trans A, vol. 50, p. 556–561, 2019.10.1007/s11661-018-5059-4 ↗
21. F. Czerwinski and B. ShalchiAmirkhiz, On the Al-Al11Ce3 eutectic transformation in aluminum-cerium binary alloys. Materials, vol. 13, no. 20, p. 4549, 2020.10.3390/ma13204549 ↗
22. [9] C. Pohla and P. Ryder, “Crystalline and quasicrystalline phases in rapidly solidified Al-Ni alloys,” Acta Mater, vol. 45, pp. 2155-2166, 1997.10.1016/S1359-6454(96)00317-5 ↗
23. [23] I. Loginova, M. Sazerat and P. Loginov, “Evaluation of microstructure and hardness of novel Al-Fe-Ni alloys with high thermal stability for laser additive manufacturing,” JOM, vol. 72, p. 3744–3752, 2020.10.1007/s11837-020-04321-2 ↗
24. [24] H. Smartt and T. Courtney, “The kinetics of coarsening in the Al-Al3Ni System,” Metall Mater Trans A, vol. 7, p. 123–126, 1976.10.1007/BF02644047 ↗
25. [6] D. Jones and G. May, “The thermal stability of the Al-Al3Ni eutectic in a temperature gradien,” Acta Metall, vol. 23, no. 1, pp. 29-34, 1975.10.1016/0001-6160(75)90066-8 ↗
26. [29] K. Gschneidner and F. Calderwood, “The Al–Ce (aluminum–cerium) system,” Bull Alloy Phase Diagr, vol. 9, no. 6, p. 669–672, 1988.10.1007/BF02883162 ↗
27. [3] W. Pearson, Handbook of Lattice Spacing and Structures of Metals and Alloys, New York: Pergamon Press, 1967.
28. [8] P. Villars, Material Phases Data System (MPDS), PAULING FILE Multinaries Edition – sd_1821912, CH-6354 Vitznau, Switzerland: Springer, 2012.
29. [10] H. Okamoto, “Al-Ni (aluminum-nickel),” J. Phase Equilibria, vol. 14, p. 257–259, 1993.10.1007/BF02667823 ↗