journal article·2017-10Open access

Experimental and Statistical Study on Machinability of the Composite Materials with Metal Matrix Al/B4C/Graphite

Engin Nas, Hasan Gökkaya

Abstract

In this study, four types of Al/B4C/Graphite metal matrix composites (MMCs) were produced by means of a hot-pressing technique with reinforcement elements, B4C 8 wt pct and graphite (nickel coated) 0, 3, 5, and 7 wt pct. Machinability tests of MMC materials thus produced were conducted using four different cutting speeds (100, 140, 180, and 220 m/min), three different feed rates (0.1, 0.15, and 0.20 mm/rev), and a fixed cutting depth (0.5 mm), and the effects of the cutting parameters on the average surface roughness were examined. After the machinability tests, the height of the built-up edge (BUE) formed on the cutting tools related to the cutting speed and feed rate was measured. The test results were examined by designing a matrix according to the full factorial design and the average surface roughness, and the most important factors leading to formation of the BUE were analyzed by the analysis of variance (ANOVA). As a result of analysis, it was found that the lowest surface roughness value was with 7 wt pct graphite MMC material, while the highest was without graphite powder. Based on the statistical analysis results, it was observed that the most important factor affecting average surface roughness was the type of MMC material, the second most effective factor was the feed rate, and the least effective factor was the cutting speed. Furthermore, it was found that the most important factor affecting the formation of the BUE was the type of MMC material, the second most effective factor was the cutting speed, and the least effective factor was the feed rate.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Titanium Alloys Microstructure and Properties · Advanced ceramic materials synthesis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (39)

Show source-provided references
1. M.K. Sanjay: Composites Manufacturing, CRC Press, Boca Raton, FL, 2002.
2. M. Pul and U. Şeker: J. Politech., 2014, vol. 17, pp. 99–106.
3. William C. Harrigan, Jr.: Mater. Sci. Eng. A, 1998, vol. 244, pp. 75–79.10.1016/S0921-5093(97)00828-9 ↗
4. R. Sekhar and T.P. Singh: J. Mater. Res. Technol., 2015, pp. 197–207.10.1016/j.jmrt.2014.10.013 ↗
5. G.B.K. Veeresh, C.S.P. Rao, N. Sevaraj, and M.S. Bhagyashekar: J. Miner. Mater. Charact. Eng., 2010, vol. 99, pp. 43–55.
6. A. Baradaswaran and A.E. Perumal: Compos. Part B: Eng., 2013, vol. 54, pp. 146–52.10.1016/j.compositesb.2013.05.012 ↗
7. K.B. Khan, T.R.G. Kutty, and M.K. Surappa: Mater. Sci. Eng. A, 2006, vol. 427, pp. 76–82.10.1016/j.msea.2006.04.015 ↗
8. H. Zhang, K.T. Ramesh, and E.S.C. Chin: Mater. Sci. Eng. A, 2004, vol. 384, pp. 26–34.10.1016/j.msea.2004.05.027 ↗
9. J. Sun, C. Liu, and R. Wang: Mater. Sci. Eng. A, 2009, vol. 519, pp. 27–31.10.1016/j.msea.2009.06.016 ↗
10. S. Yamada, K. Hirao, Y. Yamauchi et al.: J. Eur. Ceram. Soc., 2003, vol. 23, pp. 1123–30.10.1016/S0955-2219(02)00274-1 ↗
11. B.S. Lee and S. Kang: Mater. Chem. Phys., 2001, vol. 67, pp. 249–55.10.1016/S0254-0584(00)00446-6 ↗
12. S. Yamada, K. Hirao, Y. Yamauchi, and S. Kanzaki: J. Eur. Ceram. Soc., 2003, vol. 23, pp. 561–65.10.1016/S0955-2219(02)00094-8 ↗
13. S. Tdriolle, F. Thevenot, M. Aizenstein, M.P. Dariel, N. Frumin, and N. Frage: J. Solid State Chem., 2004, vol. 177, pp. 400–06.10.1016/j.jssc.2003.02.009 ↗
14. J. Deng, J. Zhou, Y. Feng, and Z. Ding: Ceram. Int., 2002, vol. 28, pp. 425–30.10.1016/S0272-8842(01)00113-4 ↗
15. A.R. Kennedy and B. Brampton: Scripta Mater., 2001, vol. 44, pp. 1077–82.10.1016/S1359-6462(01)00658-3 ↗
16. E. Ekici: Inst. Sci. Technol., 2012, pp. 113–76.
17. S.G. Upadhyaya: Cambridge International Science Publishing, 2002.
18. Hydrogen Program Plan FY 1993–FY 1997, U.S. Department of Energy, Washington, DC, 1998.
19. W.D. Kingery and H.K. Bowen: Introduction to Ceramics, 2nd ed., John Wiley & Sons, Hoboken, NJ, 1976, pp. 501–03.
20. J.B. Griffiths: Penton Press, 2001, pp. 2–3.
21. I.P. Arzibu and J.C. Perez: J. Mater. Process. Technol., 2003, vols. 143–44, pp. 390–96.
22. A. Duran and A. Acır: J. Polytech., 2004, vol. 7, pp. 211–15.
23. G. Sur and M. Gülesin: 6th Int. Advanced Technologies Symp. (IATS’11), 2011, pp. 175–79.
24. A. Baradeswaran and A.E. Perumal: Compos. Part B, 2014, vol. 56, pp. 464–71.10.1016/j.compositesb.2013.08.013 ↗
25. A. Baradeswaran and A.E. Perumal: Compos. Part B, 2014, vol. 56, pp. 472–76.10.1016/j.compositesb.2013.08.073 ↗
26. W. Ames and A.T. Alpas: Metall. Mater. Trans. A, 1995, vol. 26A, pp. 85–98.10.1007/BF02669796 ↗
27. M. Kestursatya, J.K. Kim, and P.K. Rohatgi: Mater. Sci. Eng. A, 2003, vol. 339, pp. 150–8.10.1016/S0921-5093(02)00114-4 ↗
28. B.K. Yen and T. Ishihara: Wear, 1996, pp. 169–75.10.1016/0043-1648(96)06955-4 ↗
29. S. Chenga, J. Miao, and W. Sheng: Renewable Energy, 2012, vol. 39, pp. 250–60.10.1016/j.renene.2011.08.009 ↗
30. H. Jafari, H.M. İdris, and A. Shayganpour: Trans. Nonferrous Met. Soc., 2013, vol. 23, pp. 2843–51.10.1016/S1003-6326(13)62805-8 ↗
31. T. Kıvak: Measurement, 2014, vol. 50, pp. 19–28.10.1016/j.measurement.2013.12.017 ↗
32. M. Sudheer, R. Prabhu, K. Raju, and T. Bhat: Tribology, 2013, vol. 2013, pp. 1–11.
33. A. Kumar, M.M. Mahapatra, and K.P. Jha: Measurement, 2014, vol. 48, pp. 325–32.10.1016/j.measurement.2013.11.026 ↗
34. R. Venkatesh, M.A. Hariharan, and N. Muthukrishnan: Proc. World Congr. on Engineering, 2009, vol. II, pp. 1–3.
35. H. Gökkaya: J. Eng. Sci., 2006, vol. 12, pp. 295–301.
36. J.B. Yang, C.B. Lin, T.C. Wang, and H.Y. Chu: Wear, 2004, vol. 257, pp. 941–52.10.1016/j.wear.2004.05.015 ↗
37. A. Gomez-Parra, M. Alvarez-Alcon, J. Salguero, M. Batista, and M. Marcos: Wear, 2013, vol. 302, pp. 1209–18.10.1016/j.wear.2012.12.001 ↗
38. H. Gökkaya and M. Nalbant: J. Fac. Eng. Arch., 2007, vol. 22, pp. 481–88.
39. J. K. Oishi: Mater. Process. Technol., 1996, vol. 62, pp. 331–34.10.1016/S0924-0136(96)02430-2 ↗