Bainite Formation in Medium-Carbon Low-Silicon Spring Steels Accounting for Chemical Segregation
Source abstract
Abstract
Abstract In this paper, the effect of chemical inhomogeneity on the isothermal bainite formation is investigated in medium-carbon low-silicon spring steel by dilatometry and microscopy. The analysis of the microstructure at different times during transformation shows that chemical segregation of substitutional alloying elements resulting from casting strongly affects the bainite formation by retarding the transformation kinetics and limiting the maximum achievable bainite fraction. During holding at temperatures close to and above the martensite start temperature, a homogeneous lower bainitic microstructure can be eventually obtained, whereas at higher temperatures, incomplete bainitic reaction is evident. It was also found that at the early stages of the transformation, differences in the bainite formation kinetics, due to local inhomogeneities in Cr and Mn concentration, result in retardation of the growth of bainite in the high Mn and Cr concentration regions. The calculated difference in driving force for nucleation between the enriched and the depleted areas is not by itself sufficient to explain the microstructures obtained and thus significant influence of growth on bainite formation is observed. Particularly, it was calculated and experimentally observed that Cr partitions in the carbides in the high Mn, Cr regions during the isothermal treatment, limiting the transformation kinetics.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Advanced Surface Polishing Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (20)
Show source-provided references
1. Y. Tomita and K. Okabayashi, Metall Trans A 1984, vol. 15, pp. 2247-2249.10.1007/BF02647108 ↗
2. T.Y. Kim and H.K. Kim, Mater Sci Eng: A 2013, vol. 580, pp. 322-329.10.1016/j.msea.2013.05.065 ↗
3. A. Hultgren, Trans ASM 1947, vol. 39, p. 815.
4. M. Hillert, Royal Institute of Technology, Stockholm, 1960.
5. Mats Hillert, Metall and Mater Trans A 1994, vol. 25, pp. 1957-1966.10.1007/BF02649044 ↗
6. W. T. Reynolds, S. K. Liu, F. Z. Li, S. Hartfield and H. I. Aaronson, Metallurgical Transactions A 1990, vol. 21, pp. 1479-1491.10.1007/BF02672563 ↗
7. W. T. Reynolds, F. Z. Li, C. K. Shui and H. I. Aaronson, Metall Trans A 1990, vol. 21, pp. 1433-1463.10.1007/BF02672561 ↗
8. H. I. Aaronson, W. T. Reynolds, Jr. and G. R. Purdy, Metall Mater Trans A 2004, vol. 35, pp. 1187-1210.10.1007/s11661-004-0294-2 ↗
9. C. Zener, Trans ASM 1946, vol. 167, pp. 550-95.
10. T. Ko and S.A. Cottrell, J Iron Steel Inst 1952, vol. 172, p. 307.
11. H. K. D. H. Bhadeshia and D. V. Edmonds, Acta Metall 1980, vol. 28, pp. 1265-1273.10.1016/0001-6160(80)90082-6 ↗
12. H.K.D.H. Bhadeshia, IOM Communications Ltd, London, 2001.
13. M.Y. Tu, C. A. Hsu, W.H. Wang and Y.F. Hsu, Mater Chem Phys 2008, vol. 107, pp. 418-425.10.1016/j.matchemphys.2007.08.017 ↗
14. P. Kolmskog, PhD Thesis Royal Institute of Technology (KTH) Stockholm, 2013.
15. H. Goldenstein and J. A. Cifuentes, Metall and Mater Trans A 2006, vol. 37, pp. 1747-1755.10.1007/s11661-006-0117-8 ↗
16. H. K. D. H. Bhadeshia, Mater Sci Eng: A, 1999.
17. K. R. Kinsman and H. I. Aaronson, Metall and Materi Trans 1970, vol. 1, pp. 1485-1488.10.1007/BF02900291 ↗
18. A. Borgenstam, P. Hedström, M. Hillert, P.Kolmskog, A. Stormvinter and J. Ågren, Metall Mater Trans A 2011, vol. 42, pp. 1558-1574.10.1007/s11661-010-0539-1 ↗
19. H. I. Aaronson, W. T. Reynolds, G. J. Shiflet and G. Spanos, Metall Trans A 1990, vol. 21, pp. 1343-1380.10.1007/BF02672557 ↗
20. H. Chen and S. Van Der Zwaag, Acta Mater 2014, vol. 72, pp. 1-12.10.1016/j.actamat.2014.03.034 ↗