Ultrasonic Spot Welding of a Rare-Earth Containing ZEK100 Magnesium Alloy: Effect of Welding Energy
Source abstract
Abstract
Ultrasonic spot welding was used to join a low rare-earth containing ZEK100 Mg alloy at different levels of welding energy, and tensile lap shear tests were conducted to evaluate the failure strength in relation to the microstructural changes. It was observed that dynamic recrystallization occurred in the nugget zone; the grain size increased and microhardness decreased with increasing welding energy arising from the increasing interface temperature and strain rate. The weld interface experienced severe plastic deformation at a high strain rate from ~500 to ~2100 s−1 with increasing welding energy from 500 to 2000 J. A relationship between grain size and Zener–Hollomon parameter, and a Hall–Petch-type relationship between microhardness and grain size were established. The tensile lap shear strength and failure energy were observed to first increase with increasing welding energy, reach the maximum values at 1500 J, and then decrease with a further increase in the welding energy. The samples welded at a welding energy ≤1500 J exhibited an interfacial failure mode, while nugget pull-out occurred in the samples welded at a welding energy above 1500 J. The fracture surfaces showed typical shear failure. Low-temperature tests at 233 K (−40 °C) showed no significant effect on the strength and failure mode of joints welded at the optimal welding energy of 1500 J. Elevated temperature tests at 453 K (180 °C) revealed a lower failure load but a higher failure energy due to the increased deformability, and showed a mixed mode of partial interfacial failure and partial nugget pull-out.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Magnesium Alloys: Properties and Applications · Advanced Welding Techniques Analysis · Aluminum Alloys Composites Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (74)
Show source-provided references
1. A.I. Cooper: Nature, 2015, vol. 519 (7543), pp. 294-5.10.1038/nature14212 ↗
2. M. Jakob and J. Hilaire: Nature, 2015, vol. 517(7533), pp. 150-2.10.1038/517150a ↗
3. S. Chu and A. Majumdar: Nature, 2012, vol. 488 (7411), pp. 294-303.10.1038/nature11475 ↗
4. McNutt M (2015) Science 350(6262):721.10.1126/science.aad7927 ↗
5. J.F. Nie, Y.M. Zhu, J.Z. Liu and X.Y. Fang: Science, 2013, vol. 340(6135), pp. 957-60.10.1126/science.1229369 ↗
6. T.M. Pollock: Science, 2010, vol. 328(5981), pp. 986-7.10.1126/science.1182848 ↗
7. J. Schmale, D. Shindell, E. von Schneidemesser, I. Chabay, and M. Lawrence: Nature, 2014, vol. 515(7527), pp. 335-7.10.1038/515335a ↗
8. F. Mokdad and D.L. Chen: Mater. Des., 2015, vol. 67, pp. 436-47.10.1016/j.matdes.2014.11.058 ↗
9. A. Macwan, X.Q. Jiang, and D.L. Chen: JOM, 2015, vol. 67(7), pp. 1468-77.10.1007/s11837-015-1466-9 ↗
10. F. Mokdad and D.L. Chen: Mater. Sci. Eng. A, 2015, vol. 640, pp. 243-58.10.1016/j.msea.2015.05.110 ↗
11. N. Tahreen, D.F. Zhang, F.S. Pan, X.Q. Jiang, C. Li, D.Y. Li, and D.L. Chen: J. Alloy Compd., 2015, vol. 644, pp. 814-23.10.1016/j.jallcom.2015.04.144 ↗
12. F.A. Mirza, D.L. Chen, D.J. Li, and X.Q. Zeng: Mater. Sci. Eng. A, 2013, vol. 575, pp. 65-73.10.1016/j.msea.2013.03.041 ↗
13. J. Bohlen, M.R. Nürnberg, J.W. Senn, D. Letzig, S.R. Agnew: Acta Mater., 2007, vol. 55(6), pp. 2101-12.10.1016/j.actamat.2006.11.013 ↗
14. Mirza FA, Chen DL (2013) In Aerospace Materials Handbook, Zhang S, Zhao DL (eds.) Taylor & Francis Group, Boca Raton, FL, pp. 647-98.
15. M.C. Zhao, M. Liu, G. Song, and A. Atrens: Corros. Sci., 2008, vol. 50(7), pp. 1939-53.10.1016/j.corsci.2008.04.010 ↗
16. C. Liu, D.L. Chen, S. Bhole, X. Cao, and M. Jahazi: Mater. Charact., 2009, vol. 60(5), pp. 370-6.10.1016/j.matchar.2008.10.009 ↗
17. A. Macwan, X.Q. Jiang, C. Li, and D.L. Chen: Mater. Sci. Eng. A, 2013, vol. 587, pp. 344-51.10.1016/j.msea.2013.09.002 ↗
18. Mishra RK, Gupta AK, Sikand R, Sachdev AK, Jin L (2011) In Magnesium Technology. Sillikens WH, Agnew SR, Neelameggham NR, Mathaudhu SN (eds.) Wiley, San Diego, CA, pp. 363-66.
19. J.B. Jordon, J.B. Gibson, M.F. Horstemeyer, H. El Kadiri, A.A. Luo: Mater. Sci. Eng. A, 2011, vol. 528(22-23), pp. 6860-71.10.1016/j.msea.2011.05.047 ↗
20. N. Tahreen, D.F. Zhang, F.S. Pan, X.Q. Jiang, C. Li, D.Y. Li, and D.L. Chen: J. Alloy Compd., 2014, vol. 615, pp. 424-32.10.1016/j.jallcom.2014.06.211 ↗
21. J.E. Gray and B. Luan: J. Alloy Compd., 2002, vol. 336, pp. 88-113.10.1016/S0925-8388(01)01899-0 ↗
22. M. Yamasaki, N. Hayashi, S. Izumi, and Y. Kawamura: Corros. Sci., 2007, vol. 49, pp. 255-62.10.1016/j.corsci.2006.05.017 ↗
23. F.A. Mirza, D.L. Chen, D.J. Li, and X.Q. Zeng: Metall. Mater. Trans. A, 2015, vol. 46(3), pp. 1168-87.10.1007/s11661-014-2687-1 ↗
24. F.A. Mirza, D.L. Chen, D.J. Li, and X.Q. Zeng: Mater. Des., 2014, vol. 64, pp. 63-73.10.1016/j.matdes.2014.07.016 ↗
25. H.M. Rao, R.I. Rodriguez, J.B. Jordon, M.E. Barkey, Y.B. Guo, H. Badarinarayan, and W. Yuan: Mater. Des., 2014, vol. 56, pp. 750-4.10.1016/j.matdes.2013.12.034 ↗
26. X.P. Niu, T. Skszek, M. Fabischek, A. Zak: Adv. Mater. Res., 2014, vol. 783, pp. 431-6.
27. W. Xu, L. Liu, Y. Zhou, H. Mori, D.L. Chen: Mater. Sci. Eng. A, 2013, vol. 563, pp. 125-32.10.1016/j.msea.2012.11.049 ↗
28. W. Xu, D.L. Chen, L. Liu, H. Mori and Y. Zhou: Mater. Sci. Eng. A, 2012, vol. 537(1), pp. 11-24.10.1016/j.msea.2011.12.096 ↗
29. B.S. Naik, D.L. Chen, X. Cao, and P. Wanjara, Metall. Mater. Trans. A, 2013, vol. 44A, pp. 3732-46.10.1007/s11661-013-1728-5 ↗
30. V.K. Patel, S.D. Bhole, and D.L. Chen: Scr. Mater., 2011, vol. 65(10), pp. 911-4.10.1016/j.scriptamat.2011.08.009 ↗
31. A. Macwan, V.K. Patel, X.Q. Jiang, C. Li, S.D. Bhole, and D.L. Chen: Mater. Des., 2014, vol. 62, pp. 344-51.10.1016/j.matdes.2014.05.035 ↗
32. S.H. Chowdhury, D.L. Chen, S.D. Bhole, X. Cao, and P. Wanjara : Metall. Mater. Trans. A, 2013, vol. 44(1), pp. 323-36.10.1007/s11661-012-1382-3 ↗
33. D. Bakavos, and P.B. Prangnell: Mater. Sci. Eng. A, 2010, vol. 527, pp. 6320-34.10.1016/j.msea.2010.06.038 ↗
34. J.E. Gould: Welding J., 2012, vol. 91, pp. 23s-34s.
35. R.I. Rodriguez, J.B. Jordon, H.M. Rao, H. Badarinarayan, W. Yuan, H. El Kadiri, and P.G. Allison: Mater. Sci. Eng. A, 2014, vol. 618, pp. 637-44.10.1016/j.msea.2014.09.010 ↗
36. Y.C. Chen, D. Bakavos, A. Gholinia, and P.B. Prangnell: Acta Mater., 2012, vol. 60, pp. 2816-28.10.1016/j.actamat.2012.01.047 ↗
37. V.K. Patel, S.D. Bhole, D.L. Chen: Metall. Mater. Trans. A, 2014, vol. 45A, pp. 2055-66.10.1007/s11661-013-2123-y ↗
38. Y.B. He, Q.L. Pan, Q. Chen, Z.Y. Zhang, X.Y. Liu, W.B. Li: Trans. Nonferr. Metal. Soc., 2012, vol. 22, pp. 246-54.10.1016/S1003-6326(11)61167-9 ↗
39. V.K. Patel, S.D. Bhole, and D.L. Chen: Mater. Sci. Eng. A, 2013, vol. 569, pp. 78-85.10.1016/j.msea.2013.01.042 ↗
40. N. Afrin, D.L. Chen, X. Cao, and M. Jahazi: Mater. Sci. Eng. A, 2008, vol. 472(1-2), pp. 179-86.10.1016/j.msea.2007.03.018 ↗
41. M. Fairman, N. Afrin, D.L. Chen, X.J. Cao, and M. Jahazi: Can. Metall. Quart., 2007, vol. 46(4), pp. 425-32.10.1179/cmq.2007.46.4.425 ↗
42. W.D. Callister and D.G. Rethwisch: Material Science and Engineering, 9th ed., Wiley, Inc., New Jersey, 2014, pp. 240–41.
43. N.F. Kazakov: Diffusion Bonding of Materials, Pergamon Press Canada Ltd., Ontario, 1985, pp.17–18.10.1016/B978-0-08-032550-7.50006-0 ↗
44. J.C. Tan, and M.J. Tan, Mater. Sci. Eng. A, 2003, vol. 339, pp. 124-32.10.1016/S0921-5093(02)00096-5 ↗
45. S.M. Allameh, C. Mercer, D. Popoola, and W.O. Soboyejo: J. Eng. Mater. Technol., 2005, vol. 127, pp. 65-73.10.1115/1.1836792 ↗
46. I.E. Gunduz, T. Ando, E. Shattuck, P.Y. Wong, and C.C. Doumanidis: Scripta Mater., 2005, vol. 52, pp. 939-43.10.1016/j.scriptamat.2004.12.015 ↗
47. M.R. Sriraman, S.S. Babua, and M. Short: Scripta Mater., 2010, vol. 62, pp. 560-3.10.1016/j.scriptamat.2009.12.040 ↗
48. C.J. Nonhof, M. Riepen, and A.W. Melchers: Poly. Eng. Sci., 1996, vol. 36 (15), 2018-28.10.1002/pen.10597 ↗
49. R.V. Barsukov, S.V. Levin, and I.I. Savin: Sib. Russ. Workshop and Tutor., 2002, vol. IV. pp. 39–41.10.1109/SREDM.2002.1024382 ↗
50. U. Andrade, M.A. Meyers, K.S. Vecchio, and A.H. Chokshi: Acta Metall. Mater., 1994, vol. 42 (9), 3183-95.10.1016/0956-7151(94)90417-0 ↗
51. Dieter GE (1986) In Mechanical Metallurgy. Metric SI (ed.) McGraw-Hill, London, pp. 229–35.
52. Semiatin S.L. and Jonas J.J (1984) Formability and Workability of metals, ASM, Metals Park.
53. A. Macwan and D.L. Chen, Mater. Des., 2015, vol. 84, pp. 261-9.10.1016/j.matdes.2015.06.104 ↗
54. N. Tateishi, T.H. North, and R.T. Woodhams: Poly. Eng. Sci., 1992, vol. 32(9), 600-11.10.1002/pen.760320906 ↗
55. P. Pawlow: Z. Phys. Chem., 1909, vol. 65(1), pp. 545.10.1515/zpch-1909-6532 ↗
56. S. Elangovan, S. Semeer, K. Prakasan: J. Mater. Process. Technol., 2009, vol. 209 (3), 1143-50.10.1016/j.jmatprotec.2008.03.032 ↗
57. C. Zener and H. Hollomon: J. Appl. Phys., 1944, vol. 15, pp. 22.10.1063/1.1707363 ↗
58. H.J. Forst and M.F. Ashby: Deformation Mechanism Maps; the Plasticity and Creep of Metals and Ceramics, Pergamon Press, Oxford, 1982, p. 44.
59. S.M. Fatemi-Varzaneh, A. Zarei-Hanzaki, and H. Beladi: Mater. Sci. Eng. A, 2007, vol. 456 (1-2), pp. 52-7.10.1016/j.msea.2006.11.095 ↗
60. K. Kubota, M. Mabuchi, and K. Higashi: J. Mater. Sci., 1999, vol. 34, pp. 2255-62.10.1023/A:1004561205627 ↗
61. M.R. Barnett: Mater. Trans., 2003, vol. 44, pp. 571-7.10.2320/matertrans.44.571 ↗
62. A.G. Beer: PhD Thesis, Deakin Univeristy, Deakin, Austria, 2004.
63. Z. Yu and H. Choo: Scripta Mater., 2011, vol. 64, pp. 434-7.10.1016/j.scriptamat.2010.11.009 ↗
64. C.I. Chang, C.J. Lee, and J.C. Huang: Scripta Mater., 2004, vol. 51, pp. 509-14.10.1016/j.scriptamat.2004.05.043 ↗
65. B.S. Naik, D.L. Chen, X. Cao, and P. Wanjara, Metall. Mater. Trans. A, 2014, vol. 45(10), pp. 4333-49.10.1007/s11661-014-2372-4 ↗
66. C. Zhang and L. Li. (2009). Metall. Mater. Trans. B, 2009, vol. 40(2), 196-207.10.1007/s11663-008-9224-9 ↗
67. D.R. Milner and G.W. Rowe: Metall. Reviews, 1962, vol. 7(1), pp. 433-80.10.1179/mtlr.1962.7.1.433 ↗
68. Y. Chino, K. Sassa, and A. Kamiya: Mater. Sci. Eng. A, 2006, vol. 441(1-2), pp. 349-56.10.1016/j.msea.2006.08.038 ↗
69. G.G. Harman, and J. Albers: IEEE Trans. PHP, 1977, 13, pp. 406-12.
70. A.G. Truog: Master Thesis, The Ohio State University, Columbus, 2012.
71. T.H. Youssef and R.A. Essawi: Czech J. Phys., 1979, B29, pp. 1266-70.10.1007/BF01590447 ↗
72. J. Koike, Y. Sato and D. Ando: Mater. Trans., 2008, vol. 49(12), pp. 2792-800.10.2320/matertrans.MRA2008283 ↗
73. D. Sarker and D.L. Chen: Mater. Sci. Eng. A, 2014, vol. 596, pp. 134-44.10.1016/j.msea.2013.12.038 ↗
74. D. Sarker, J. Friedman, and D.L. Chen: J. Mater. Sci. Technol., 2014, vol. 30(9), pp. 884-7.10.1016/j.jmst.2014.06.011 ↗