Plastic Flow and Microstructure Evolution during Low-Temperature Superplasticity of Ultrafine Ti-6Al-4V Sheet Material
Source abstract
Abstract
The low-temperature superplastic (SP) flow behavior of two lots of Ti-6Al-4V sheet, each with an ultrafine microstructure, was established by performing tension tests at temperatures of 775 °C and 815 °C and true strain rates of 10−4 and 10−3 s−1. The as-received microstructures of the two materials comprised either equiaxed or slightly elongated alpha particles in a beta matrix. The material with equiaxed alpha particles exhibited flow hardening, which was correlated with concurrent (dynamic) coarsening. The rate of dynamic coarsening was rationalized in terms of static coarsening measurements and the enhancement of kinetics due to pipe diffusion. By contrast, the material with initially elongated alpha particles exhibited comparable flow hardening at the lower strain rate but a complex, near-steady-state behavior at the higher strain rate. These latter observations were explained on the basis of the evolution of the alpha particle shape and size during straining; dynamic coarsening or dynamic spheroidization was concluded to be most important at the lower and higher strain rates, respectively. The plastic flow behavior was interpreted in the context of a long-wavelength flow localization analysis.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and mechanical properties · Advanced materials and composites · High-Velocity Impact and Material Behavior
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (31)
Show source-provided references
1. Ultrafine Grained Materials III, Y.T. Zhu, T.G. Langdon, R.Z. Valiev, S.L. Semiatin, D.H. Shin, and T.C. Lowe, eds., TMS, Warrendale, PA, 2004.
2. Ultrafine Grained Materials IV, Y.T. Zhu, T.G. Langdon, Z. Horita, M.J. Zehetbauer, S.L. Semiatin, and T.C. Lowe, eds., TMS, Warrendale, PA, 2006.
3. Proc. 2nd Int. Conf. on Nanomaterials by Severe Plastic Deformation: Fundamentals—Processing—Applications, M.J. Zehetbauer and R.Z. Valiev, eds., Wiley-VCH, Weinheim, Germany, 2004.
4. A.K. Ghosh and C.H. Hamilton: Metall. Trans. A, 1979, vol. 10A, pp. 699–706.10.1007/BF02658391 ↗
5. S.M.L. Sastry, R.J. Lederich, T.L. Mackay, and W.R. Kerr: J. Met., 1983, vol. 35 (1), pp. 48–53.
6. H. Inagaki: Z. Metallkd., 1995, vol. 86, pp. 643–50.
7. S.V. Zherebstov, G.A. Salishchev, R.M. Galeyev, O.R. Valiakhmetov, and S.L. Semiatin: Proc. 2nd Int. Conf. on Nanomaterials by Severe Plastic Deformation: Fundamentals—Processing—Applications, M.J. Zehetbauer and R.Z. Valiev, eds., Wiley-VCH, Weinheim, Germany, 2004, pp. 835–40.10.1002/3527602461.ch15h ↗
8. G.A. Salishchev, R.M. Galeyev, O.R. Valiakhmetov, R.V. Safiullin, R.Y. Lutfullin, O.N. Senkov, F.H. Froes, and O.A. Kaibyshev: J. Mater. Process. Technol., 2001, vol. 116, pp. 265–68.10.1016/S0924-0136(01)01037-8 ↗
9. Y.G. Ko, C.S. Lee, D.H. Shin, and S.L. Semiatin: Metall. Mater. Trans. A, 2006, vol. 37A, pp. 381–91.10.1007/s11661-006-0008-z ↗
10. A.K. Ghosh: University of Michigan, Ann Arbor, MI, unpublished research, 2006.
11. A.V. Sergueeva, V.V. Stolyarov, R.Z. Valiev, and A.K. Mukherjee: Mater. Sci. Eng., A, 2002, vol. A323, pp. 318–25.10.1016/S0921-5093(01)01384-3 ↗
12. R.S. Mishra, V.V. Stolyarov, C. Echer, R.Z. Valiev, and A.K. Mukherjee: Mater. Sci. Eng., A, 2001, vol. A298, pp. 44–50.10.1016/S0921-5093(00)01338-1 ↗
13. P.N. Comley: J. Mater. Eng. Perform., 2004, vol. 13, pp. 660–64.10.1361/10599490421259 ↗
14. S.N. Patankar, J.P. Escobedo, D.P. Field, G. Salishchev, R.M. Galeyev, O.R. Valiakhmetov, and F.H. Froes: J. Alloys Compd., 2002, vol. 345, pp. 221–27.10.1016/S0925-8388(02)00406-1 ↗
15. P.N. Comley: Mater. Sci. Forum, 2004, vols. 447–448, pp. 233–38.10.4028/www.scientific.net/MSF.447-448.233 ↗
16. G.A. Sargent, A.P. Zane, P.N. Fagin, A.K. Ghosh, and S.L. Semiatin: Metall. Mater. Trans. A, 2008, vol. 39A, pp. 2949–64.10.1007/s11661-008-9650-y ↗
17. J.A. Wert and N.E. Paton: Metall. Trans. A, 1983, vol. 14A, pp. 2535–44.10.1007/BF02668895 ↗
18. P.A. Friedman and A.K. Ghosh: Metall. Mater. Trans. A, 1996, vol. 27A, pp. 3030–42.10.1007/BF02663852 ↗
19. S.L. Semiatin and J.J. Jonas: Formability and Workability of Metals: Plastic Instability and Flow Localization, ASM, Metals Park, OH, 1984.
20. S.L. Semiatin, A.K. Ghosh, and J.J. Jonas: Metall. Trans. A, 1985, vol. 16A, pp. 2291–98.10.1007/BF02670429 ↗
21. R.C. Gifkins: Metall. Trans. A, 1976, vol. 7A, pp. 1225–32.10.1007/BF02656607 ↗
22. M. Kawasaki and T.G. Langdon: J. Mater. Sci., 2007, vol. 42, pp. 1782–96.10.1007/s10853-006-0954-2 ↗
23. S.L. Semiatin, M.W. Corbett, P.N. Fagin, G.A. Salishchev, and C.S. Lee: Metall. Mater. Trans. A, 2006, vol. 37A, pp. 1125–36.10.1007/s11661-006-1091-x ↗
24. C.S. Smith: Trans. AIME, 1948, vol. 175, pp. 47–48.
25. J.E. Bird, A.K. Mukherjee, and J.E. Dorn: in Quantitative Relation between Microstructure and Properties, D.G. Brandon and A. Rosen, eds., Israel Universities Press, Jerusalem, Israel, 1969, pp. 255–342.
26. S.L. Semiatin and G.A. Sargent: Key Eng. Mater., 2009, in press.
27. E.B. Shell and S.L. Semiatin: Metall. Mater. Trans. A, 1999, vol. 30A, pp. 3219–29.10.1007/s11661-999-0232-4 ↗
28. S.L. Semiatin, V. Seetharaman, and I. Weiss: Mater. Sci. Eng., A, 1999, vol. A263, pp. 257–71.10.1016/S0921-5093(98)01156-3 ↗
29. S.L. Semiatin, N. Stefansson, and R.D. Doherty: Metall. Mater. Trans. A, 2005, vol. 36A, pp. 1372–76.10.1007/s11661-005-0229-6 ↗
30. S.L. Semiatin and T.R. Bieler: Acta Mater., 2001, vol. 49, pp. 3565–73.10.1016/S1359-6454(01)00236-1 ↗
31. M.G. Zelin and A.K. Mukherjee: Mater. Sci. Eng., A, 1996, vol. A208, pp. 210–25.10.1016/0921-5093(95)10080-6 ↗