Method of Evaluating Hydrogen Embrittlement Susceptibility of Tempered Martensitic Steel Showing Intergranular Fracture
Source abstract
Abstract
A stress application method in delayed fracture susceptibility tests was investigated using 1450 MPa class tempered martensitic steel. Its fracture mode under hydrogen charging was mainly intergranular because of its relatively small Si content of 0.21 mass pct. The conditions for consistency in fracture strength between tensile tests and constant load tests (CLTs) were clarified: first, to conduct hydrogen precharging before stress application; and second, to choose a sufficiently low crosshead speed in tensile tests. When hydrogen precharging was not conducted before CLTs, the fracture strength was higher than the values in CLTs with hydrogen charging and in tensile tests. If the crosshead speed was too high, the fracture strength obtained was higher than the values in CLTs. The dependence of the fracture strength on crosshead speed was seen for both notched and smooth bar specimens. These results suggested that plastic deformation, i.e., dislocation motion, was related to intergranular fracture with a tear pattern as well as to quasi-cleavage fracture. In addition, cathodic electrolysis in an alkaline solution containing NaOH should be used as the hydrogen charging method to avoid the effects of corrosion.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Hydrogen embrittlement and corrosion behaviors in metals · Corrosion Behavior and Inhibition · Fatigue and fracture mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (46)
Show source-provided references
1. Y. H. Kim and J. W. Morris, Metall. Trans. A, 1983, vol. 14A, pp. 1883–88.10.1007/BF02645559 ↗
2. M. Gao and R. P. Wei, Acta Metall., 1984, vol. 32, pp. 2115–24.10.1016/0001-6160(84)90190-1 ↗
3. A. Shibata, H. Takahashi, and N. Tsuji, ISIJ Int., 2012, vol. 52, pp. 208–12.10.2355/isijinternational.52.208 ↗
4. H. K. Birnbaum and P. Sofronis, Mater. Sci. Eng. A, 1994, vol. A176, pp. 191–202.10.1016/0921-5093(94)90975-X ↗
5. P. Sofronis and H. K. Birnbaum, J. Mech. Phys. Solids, 1995, vol. 43, pp. 49–90.10.1016/0022-5096(94)00056-B ↗
6. I. M. Robertson, Eng. Fract. Mech., 2001, vol. 68, pp. 671–92.10.1016/S0013-7944(01)00011-X ↗
7. M. Nagumo, Mater. Sci. Technol., 2004, vol. 20, pp. 940–50.10.1179/026708304225019687 ↗
8. M. Nagumo, M. Nakamura, and K. Takai, Metall. Mater. Trans. A, 2001, vol. 32A, pp. 339–47.10.1007/s11661-001-0265-9 ↗
9. A. Nagao, C. D. Smith, M. Dadfarnia, P. Sofronis, and I. M. Robertson, Acta Mater., 2012, vol. 60, pp. 5182–89.10.1016/j.actamat.2012.06.040 ↗
10. O. A. Onyewuenyi and J. P. Hirth, Metall. Trans. A, 1983, vol. 14A, pp. 259–69.10.1007/BF02651623 ↗
11. T. Doshida, H. Suzuki, K. Takai, N. Oshima, and T. Hirade, ISIJ Int., 2012, vol. 52, pp. 198–207.10.2355/isijinternational.52.198 ↗
12. T. Neeraj, R. Srinivasan, and J. Li, Acta Mater., 2012, vol. 60, pp. 5160–71.10.1016/j.actamat.2012.06.014 ↗
13. C. J. McMahon, Eng. Fract. Mech., 2001, vol. 68, pp. 773–88.10.1016/S0013-7944(00)00124-7 ↗
14. N. J. Petch, Philos. Mag., 1956, vol. 1, pp. 331–37.10.1080/14786435608238106 ↗
15. R. P. Frohmberg, W. J. Barnett, and A. R. Troiano, Trans. ASM, 1955, vol. 47, pp. 892–925.
16. R. A. Oriani and P. H. Josephic, Acta Metall., 1974, vol. 22, pp. 1065–74.10.1016/0001-6160(74)90061-3 ↗
17. J. R. Rice and J. S. Wang, Mater. Sci. Eng. A, 1989, vol. A107, pp. 23–40.10.1016/0921-5093(89)90372-9 ↗
18. M. Yamaguchi, K. Ebihara, M. Itakura, T. Kadoyoshi, T. Suzudo, and H. Kaburaki, Metall. Mater. Trans. A, 2011, vol. 42A, pp. 330–39.10.1007/s11661-010-0380-6 ↗
19. M. Yamaguchi, Metall. Mater. Trans. A, 2011, vol. 42A, pp. 319–29.10.1007/s11661-010-0381-5 ↗
20. P. Novak, R. Yuan, B. P. Somerday, P. Sofronis, and R. O. Ritchie, J. Mech. Phys. Solids, 2010, vol. 58, pp. 206–26.10.1016/j.jmps.2009.10.005 ↗
21. Y. Takeda and C. J. McMahon, Metall. Trans. A, 1981, vol. 12A, pp. 1255–66.10.1007/BF02642339 ↗
22. Y. Matsumoto and K. Takai, Metall. Mater. Trans. A, 2017, vol. 48A, pp. 666–77.10.1007/s11661-016-3885-9 ↗
23. Y. Matsumoto, K. Takai, M. Ichiba, T. Suzuki, T. Okamura, and S. Mizoguchi, ISIJ Int., 2013, vol. 53, pp. 714–22.10.2355/isijinternational.53.714 ↗
24. M. Wang, E. Akiyama, and K. Tsuzaki, Scr. Mater., 2005, vol. 53, pp. 713–18.10.1016/j.scriptamat.2005.05.014 ↗
25. Y. Hagihara, T. Shobu, N. Hisamori, H. Suzuki, K. Takai, and K. Hirai, ISIJ Int., 2012, vol. 52, pp. 298–306.10.2355/isijinternational.52.298 ↗
26. J. A. Donovan, Metall. Trans. A, 1976, vol. 7A, pp. 1677–83.10.1007/BF02817885 ↗
27. H. Shoda, H. Suzuki, K. Takai, and Y. Hagihara, ISIJ Int., 2010, vol. 50, pp. 115–23.10.2355/isijinternational.50.115 ↗
28. K. Takai, H. Shoda, H. Suzuki, and M. Nagumo, Acta Mater., 2008, vol. 56, pp. 5158–67.10.1016/j.actamat.2008.06.031 ↗
29. T. Doshida and K. Takai, Acta Mater., 2014, vol. 79, pp. 93–107.10.1016/j.actamat.2014.07.008 ↗
30. K. Sakaki, T. Kawase, M. Hirato, M. Mizuno, H. Araki, Y. Shirai, and M. Nagumo, Scr. Mater., 2006, vol. 55, pp. 1031–34.10.1016/j.scriptamat.2006.08.030 ↗
31. R. Gopaliengar, J. P. Wallace, and R. A. Oriani, Mater. Sci. Eng., 1984, vol. 68, pp. 191–96.10.1016/0025-5416(85)90408-2 ↗
32. J. Kameda and M. L. Jokl, Scr. Metall., 1982, vol. 16, pp. 325–30.10.1016/0036-9748(82)90362-3 ↗
33. N. Ishikawa, H. Sueyoshi, and A. Nagao, ISIJ Int., 2016, vol. 56, pp. 413–17.10.2355/isijinternational.ISIJINT-2015-329 ↗
34. M. Nagumo and H. Matsuda, Philos. Mag. A, 2002, vol. 82, pp. 3415–25.10.1080/01418610208240452 ↗
35. D. H. Lassila and H. K. Birnbaum, Acta Metall., 1986, vol. 34, pp. 1237–43.10.1016/0001-6160(86)90010-6 ↗
36. M. L. Martin, B. P. Somerday, R. O. Ritchie, P. Sofronis, and I. M. Robertson, Acta Mater., 2012, vol. 60, pp. 2739–45.10.1016/j.actamat.2012.01.040 ↗
37. H. Hänninen and T. Hakkarainen, Metall. Trans. A, 1979, vol. 10A, pp. 1196–99.10.1007/BF02811667 ↗
38. S. Wang, M. L. Martin, P. Sofronis, S. Ohnuki, N. Hashimoto, and I. M. Robertson, Acta Mater., 2014, vol. 69, pp. 275–82.10.1016/j.actamat.2014.01.060 ↗
39. T. Tabata and H. K. Birnbaum, Scr. Metall., 1984, vol. 18, pp. 231–36.10.1016/0036-9748(84)90513-1 ↗
40. I. M. Robertson and H. K. Birnbaum, Acta Metall., 1986, vol. 34, pp. 353–66.10.1016/0001-6160(86)90071-4 ↗
41. W. W. Gerberich, T. Livne, X. F. Chen, and M. Kaczorowski, Metall. Trans. A, 1988, vol. 19A, pp. 1319–34.10.1007/BF02662593 ↗
42. A. Shibata, T. Murata, H. Takahashi, T. Matsuoka, and N. Tsuji, Metall. Mater. Trans. A, 2015, vol. 46A, pp. 5685–96.10.1007/s11661-015-3176-x ↗
43. T. Nakamoto, H. Suzuki, H. Saito, T. Sawada, and K. Takai: in proc. Materials Science & Technology (MS&T), Colombus, OH, 2011, pp. 1226–33.
44. T. Doshida, M. Nakamura, H. Saito, T. Sawada, and K. Takai, Acta Mater., 2013, vol. 61, pp. 7755–66.10.1016/j.actamat.2013.09.015 ↗
45. H. R. Higgy and F. H. Hammad, J. Nucl. Mater., 1975, vol. 55, pp. 177–86.10.1016/0022-3115(75)90151-8 ↗
46. M. Nagumo, T. Yagi, and H. Saitoh, Acta Mater., 2000, vol. 48, pp. 943–51.10.1016/S1359-6454(99)00392-4 ↗