Strain Rate and Temperature Effects on the Formability and Damage of Advanced High-Strength Steels
Source abstract
Abstract
In order to understand the crashworthiness and formability of advance high-strength steels, the effects of strain rate and temperature on the constitutive response of DP 600 and DP 780 steel tubes were investigated and compared with commercial drawing quality (DQ) and high strength low alloy (HSLA) 350 steel tubes. Uniaxial tensile tests were conducted at quasi-static (QS) (0.003 and 0.1 s−1), intermediate (30 and 100 s−1), and high (500, 1000, and 1500 s−1) strain rates using an Instron, instrumented falling weight impact tester and tensile split Hopkinson bar (TSHB) apparatus, respectively. Elevated temperature tests at 150 °C and 300 °C were also conducted at high strain rates. Following testing, metallography and microscopy techniques were used for material and damage characterization. The results obtained show that the steels studied exhibit a positive strain rate sensitivity. Compared to DQ and HSLA 350, the DP steels were found to have less formability at QS rates but enhanced formability at higher strain rates. A decrease in strength and ductility was measured with increasing temperature for the DP steels, indicating a reduction in energy adsorption due to adiabatic heating during a crash event.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High-Velocity Impact and Material Behavior · Structural Response to Dynamic Loads · Nuclear and radioactivity studies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (20)
Show source-provided references
1. G.R. Speich: Fundamentals of Dual-Phase Steels, The Metallurgical Society, Warrendale, PA, 1981, pp. 1–45
2. W.F. Smith: Structure and Properties of Engineering Alloys, 2nd ed, McGraw-Hill Inc., New York, NY, 1993, pp. 119–23
3. N.D. Beynon, T.B. Jones, G. Fourlaris: Mater. Sci. Technol., 2005, vol. 21 (1), pp. 103–12.10.1179/174328405X16234 ↗
4. N.D. Beynon, S. Oliver, T.B. Jones, G. Fourlaris: Mater. Sci. Technol., 2005, vol. 21 (7), pp. 771–7810.1179/174328405X41038 ↗
5. W. Bleck, I. Schael: Steel Res., 2000, vol. 71 (5), pp. 173–7810.1002/srin.200005709 ↗
6. V. Tarigopula, M. Langseth, O.S. Hopperstad, A.H. Clausen: Int. J. Impact Eng., 2006, vol. 32, pp. 847–8210.1016/j.ijimpeng.2005.07.010 ↗
7. H. Huh, S.-B. Kim, J.-H. Song, and J.-H. Lim: Int. Mech. Sci., 2003, vol. 45, no. 10, pp. 1645–6010.1016/j.ijmecsci.2003.09.022 ↗
8. A. Thompson, C. Salisbury, M. Worswick, and R. Mayer: J. Phys. IV France, 2006, v0l. 134, pp. 281–8610.1051/jp4:2006134043 ↗
9. A. Thompson: MASc Thesis, University of Waterloo, Waterloo, ON, Canada, 2006
10. R. Smerd, S. Winkler, C. Salisbury, M.J. Worswick, D.J. Lloyd, M.J. Finn: Int. J. Impact Eng., 2005, vol. 32 (1–4), pp. 541–6010.1016/j.ijimpeng.2005.04.013 ↗
11. R. Smerd: MASc Thesis, University of Waterloo, Waterloo, ON, Canada, 2005
12. Annual Book of ASTM Standards: Metals––Mechanical Testing; Elevated and Low Temperature Tests; Metallography, S.J. Bailey, N.C. Baldini, E.I. Barkley, K.A. Peters, J.L. Rosiak, S.T. Simms, E.A. Whealen, and R.F. Wilhelm, eds., ASTM International, West Conshohocken, PA, 2003, pp. 61–82
13. K.P. Staubhammer, L.E. Murr: Mater. Sci. Eng., 1980, vol. 44, pp. 97–11310.1016/0025-5416(80)90235-9 ↗
14. J. Van Slycken, P. Verleysen, J. Degrieck, L. Samek, B.C. De Cooman: Metall. Mater. Trans. A, 2006, vol. 37A, pp. 1527–3910.1007/s11661-006-0097-8 ↗
15. S.L. Winkler, Y. Ososkov, A. Bardelcik, M. Jain, D.S. Wilkinson, and M.J. Worswick: Proc. SAE 2005, SAE Inc., Houston, TX, SAE paper no. 2005-01-0092
16. M. Mazanani, W.J. Poole: Metall. Mater. Trans. A, 2007, vol. 38A, pp. 328–3910.1007/s11661-006-9023-3 ↗
17. M.M. Astakhov, A.N. Golenchenko, A.V. Loginov, L.P. Loshmanov, and A.E. Trotsenko: Special Features of Dynamic Strain Aging in High-Speed Tension of Steel 20, Moscow Institute of Engineering Physics, Moscow; translated from Problemy Prochnosti, 1991, No. 9, pp. 28–3010.1007/BF00770923 ↗
18. S.H. Mousavi Anijdan, H. Vahdani: Mater. Lett., 2005, vol. 59, pp. 1828–3010.1016/j.matlet.2004.08.046 ↗
19. S. Gündüz, R.C. Cochrane: Mater. Sci. Technol., 2003, vol. 19, pp. 422–2810.1179/026708303225001984 ↗
20. S. Gündüz, M. Acarer: Industr. Lubric. Tribol., 2005, vol. 57, pp. 145–4910.1108/00368790510601699 ↗