journal article·2015-11Open access

A Microstructural Study on the Observed Differences in Charpy Impact Behavior Between Hot Isostatically Pressed and Forged 304L and 316L Austenitic Stainless Steel

Adam J. Cooper, Norman I. Cooper, Andrew Bell, Jean Dhers, Andrew H. Sherry

Abstract

Abstract With near-net shape technology becoming a more desirable route toward component manufacture due to its ability to reduce machining time and associated costs, it is important to demonstrate that components fabricated via Hot Isostatic Pressing (HIP) are able to perform to similar standards as those set by equivalent forged materials. This paper describes the results of a series of Charpy tests from HIP’d and forged 304L and 316L austenitic stainless steel, and assesses the differences in toughness values observed. The pre-test and post-test microstructures were examined to develop an understanding of the underlying reasons for the differences observed. The as-received microstructure of HIP’d material was found to contain micro-pores, which was not observed in the forged material. In tested specimens, martensite was detectable within close proximity to the fracture surface of Charpy specimens tested at 77 K (−196 °C), and not detected in locations remote from the fracture surface, nor was martensite observed in specimens tested at ambient temperatures. The results suggest that the observed changes in the Charpy toughness are most likely to arise due to differences in as-received microstructures of HIP’d vs forged stainless steel.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Metal Alloys Wear and Properties · Microstructure and Mechanical Properties of Steels · Powder Metallurgy Techniques and Materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (31)

Show source-provided references
1. H. V. Atkinson and S. Davies, Metall. Mater. Trans. A 2000, vol. 31, pp. 2981–3000.10.1007/s11661-000-0078-2 ↗
2. Charles Barre, Adv. Mater. Process. 1999, vol. 155, pp. 47–48.
3. N. A. Fleck and R. A. Smith, Powder Metall. 1981, vol. 24, pp. 121–25.10.1179/pom.1981.24.3.121 ↗
4. G. A. Rao and M. Kumar, Mater. Sci. Technol. 1997, vol. 13, pp. 1027–31.10.1179/mst.1997.13.12.1027 ↗
5. J.J. Eckenrod and K.E. Pinnow: Advances in Powder Metallurgy and Particulate Materials, (1993), pp. 131–40.
6. H. T. Larker and R. Lundberg, J. Eur. Ceram. Soc. 1999, vol. 19, pp. 2367–73.10.1016/S0955-2219(99)00109-0 ↗
7. Y. C. Jeon and K. T. Kim, Int. J. Mech. Sci. 1999, vol. 41, pp. 815–30.10.1016/S0020-7403(98)00053-8 ↗
8. G. A. Rao, D. V. V. Satyanarayana, M. Srinivas and D. S. Sarma, Powder Metall. 2009, vol. 52, pp. 244–49.10.1179/003258909X12450768327180 ↗
9. V. Viswanathan, T. Laha, K. Balani, A. Agarwal and S. Seal, Mater. Sci. Eng. R, 2006, vol. 54, pp. 121–85.10.1016/j.mser.2006.11.002 ↗
10. J.K.L. Lai, K.H. Lo and C.H. Shek: Stainless Steel An Introduction and their Recent Developments, 2012.
11. P. J. Jacques, J. Ladrière and F. Delannay, Metall. Mater. Trans. A 2001, vol. 32, pp. 2759–68.10.1007/s11661-001-1027-4 ↗
12. H. F. López and A. J. Saldivar-Garcia, Metall. Mater. Trans. A 2008, vol. 39, pp. 8–18.10.1007/s11661-007-9370-8 ↗
13. Nishiyama Z (2012) Martensitic Transformation. Elsevier, Amsterdam.
14. S. M. C. van Bohemen and J. Sietsma, Metall. Mater. Trans. A, 2009, vol. 40, pp. 1059–68.10.1007/s11661-009-9796-2 ↗
15. S. S. Hecker, M. G. Stout, K. P. Staudhammer and J. L. Smith, MTA 1982, vol. 13, pp. 619–26.10.1007/BF02644427 ↗
16. Skoczeń BT (2004) Compensation Systems for Low Temperature Applications. Springer, Berlin, pp 119–36.10.1007/978-3-662-06305-7 ↗
17. S. Takahashi, J. Echigoya, T. Ueda, X. Li and H. Hatafuku, J. Mater. Process. Technol. 2001, vol. 108, pp. 213–16.10.1016/S0924-0136(00)00757-3 ↗
18. K. P. Staudhammer, L. E. Murr and S. S. Hecker, Acta Metallurgica 1983, vol. 31, pp. 267–74.10.1016/0001-6160(83)90103-7 ↗
19. Ercan Cakmak, Sven C. Vogel and Hahn Choo, Mater. Sci. Eng. A, 2014, vol. 589, pp. 235–41.10.1016/j.msea.2013.09.093 ↗
20. ASTM A370-14: Standard Test Methods and Definitions for Mechanical Testing of Steel Products, ASTM International, West Conshohocken, 2014.
21. ASTM E3-01: Standard Practice for Preparation of Metallographic Specimens. ASTM International, West Conshohocken, 2001.
22. ASTM E112-96: Standard Test Methods for Determining Average Grain Size. ASTM International, West Conshohocken, 1996.
23. H.-J. Christ, U. Krupp, C. Mueller-Bollenhagen, I. Roth and M. Zimmermann: Proceedings of the 12th International Conference on Fracture, Ottawa, Canada, 2009.
24. J. Liao, M. Hotta and A. Koshi, Materials Letters 2011, vol. 65, pp. 2995–99.10.1016/j.matlet.2011.06.028 ↗
25. Y. Sato, T. Maie and T. Kuwana: Proceedings of the International Conference on Offshore Mechanics and Arctic Engineering—OMAE, 1995, pp. 485–90.
26. O. Kamiya, H. Fujita, T. Enjo and Y. Kikuchi, Q. J. Jpn. Weld. Soc. 1985, vol. 3, pp. 574–81.10.2207/qjjws.3.574 ↗
27. Z. Oksiuta, E. Boehm-Courjault and N. Baluc, J. Mater. Sci. 2010, vol. 45, pp. 3921–30.10.1007/s10853-010-4457-9 ↗
28. A. Lind, J. Sundström and A. Peacock, Fusion Eng. Des. 2005, vol. 75–79, pp. 979–83.10.1016/j.fusengdes.2005.06.301 ↗
29. M. Godec, Mater. Tehnol. 2011, vol. 45, pp. 85–90.
30. J. Man, K. Obrtlík, M. Petrenec, P. Beran, M. Smaga, A. Weidner, J. Dluhoš, T. Kruml, H. Biermann, D. Eifler and J. Polák, Proc. Eng. 2011, vol. 10, pp. 1279–84.10.1016/j.proeng.2011.04.213 ↗
31. Y. Matsuoka, T. Iwasaki, N. Nakada, T. Tsuchiyama and S. Takaki, ISIJ Int. 2013, vol. 53, pp. 1224–30.10.2355/isijinternational.53.1224 ↗