journal article·2018-10

Chemistry and Properties of Medium-Mn Two-Stage TRIP Steels

Daniel M. Field, Jingjing Qing, David C. Van Aken

Publisher page

Abstract

Eight medium manganese steels ranging from 10 to 15 wt pct Mn have been produced with varying levels of aluminum, silicon, and carbon to create steels with varying TRIP (transformation-induced plasticity) character. Alloy chemistries were formulated to produce a range of intrinsic stacking fault energies (ISFE) from − 2.2 to 13.3 mJ/m2 when calculated at room temperature for an austenitic microstructure having the nominal alloy composition. Two-stage TRIP behavior was documented when the ISFE of the γ-austenite phase was 10.5 mJ/m2 or less, whereas an ISFE of 11.9 mJ/m2 or greater exhibited TWIP (twin-induced plasticity) with single-stage TRIP to form α-martensite. Properties were measured in both hot band (hot rolled) and batch annealed (hot rolled, cold rolled, and annealed) conditions. Hot band properties were influenced by the Si/Al ratio and this dependence was related to incomplete recovery during hot working for alloys with Si/Al ratios greater than one. Batch annealing was conducted at 873 K (600 °C) for 20 hours to produce ultrafine-grained microstructures with mean free slip distances less than 1 μm. Batch-annealed materials were found to exhibit a Hall–Petch dependence of the yield strength upon the mean free slip distance measured in the polyphase microstructure. Ultimate tensile strengths ranged from 1450 to 1060 MPa with total elongations of 27 to 43 pct. Tensile ductility was shown to be proportional to the sum of the products of volume fraction transformed times the volume change associated for each martensitic transformation. An empirical relationship based upon the nominal chemistry was derived for the ultimate tensile strength and elongation to failure for these batch-annealed steels. Two additional alloys were produced based upon the developed understanding of these two-stage TRIP steels and tensile strengths of 1150 MPa with 58 pct total elongation and 1400 MPa and 32 pct ductility were achieved.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Magnetic Properties and Applications · Hydrogen embrittlement and corrosion behaviors in metals

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (59)

Show source-provided references
1. Q. Li, X. Huang, and W. Huang: Met Sci. Eng., 2016, vol. 662, pp. 129-35.10.1016/j.msea.2016.03.042 ↗
2. E.J. Seo, L. C, Y. Estrin, and B.C. De Cooman: Acta Mater., 2016, vol. 113, pp. 124-3910.1016/j.actamat.2016.04.048 ↗
3. L. Cho, E.J. Seo, and B.C. De Cooman: Scripta Materialia, 2016, vol. 123, pp. 69-7210.1016/j.scriptamat.2016.06.003 ↗
4. T. Tschiyama, T. Inoe, J. Tobata, D. Akami, and S. Takaki: Scripta Mat. 2016, vol. 122, pp. 36-3910.1016/j.scriptamat.2016.05.019 ↗
5. D.-W. Suh, S.-J. Park, T.-H. Lee, C.-S. Oh, and S.-J. Kim: Met Trans A, 2010, vol. 41A, pp. 397–40810.1007/s11661-009-0124-7 ↗
6. D.-W. Suh, J.-H. Ryu, M.-S. Joo, H.-S. Yang, H.K.D.H. Bhadeshia: Met Trans A, 2013, vol. 44A, pp. 286–9310.1007/s11661-012-1402-3 ↗
7. J. Shi, X. Sun, M. Wang, W. Hui, H. Dong, and W. Cao: Scripta Mat, 2010, vol. 63, pp. 815-1810.1016/j.scriptamat.2010.06.023 ↗
8. Z.H. Cai, H. Ding, R.D.Misra, and Z.Y. Ying: Acta Materialia, 2015, vol. 84, pp. 229-3610.1016/j.actamat.2014.10.052 ↗
9. R. Zhang, W.Q. Ca, Z.J. Peng, J. Shi, H. Dong, and C.X. Huang: Mater. Sci. & Eng. A, 2013, vol. 583, pp. 84-8810.1016/j.msea.2013.06.067 ↗
10. R. Skolly, ArcelorMittal personal communication.
11. Y. Zhang, L. Wang, K. O. Findley, and J. Speer: Met Trans. A, 2017, vol. 48A, pp. 2140-4910.1007/s11661-017-3995-z ↗
12. H. Luo, H. Dong, and M. Huang: Mater. & Design, 2015, vol. 83, pp.42-4810.1016/j.matdes.2015.05.085 ↗
13. S. Lee, W. Woo, and B.C. De Cooman: Met. Trans A, 2016, vol. 47A, pp. 2125-4010.1007/s11661-016-3407-9 ↗
14. G. Frommeyer, U. Brux, and P. Neumann: ISJ Inter. 2003, vol. 43, pp. 438-4610.2355/isijinternational.43.438 ↗
15. L. Remy, and A. Pineau: Mater. Sci and Eng. 1976, vol. 26 pp. 123-3210.1016/0025-5416(76)90234-2 ↗
16. S. Allain, J.P. Chateau, and O. Bouaziz: Mater Sci and Eng. 2004, vol. 387, pp. 143-4710.1016/j.msea.2004.01.060 ↗
17. T.H. Lee, E. Shin, C.S. Oh, H.Y. Ha, and S.J. Kim: Acta Mater. 2010, vol. 58, 3173-8610.1016/j.actamat.2010.01.056 ↗
18. H. Song, S.S. Sohn, J-H Kwak, B-J lee, and S. Lee: Met Trans A, 2016, vol. 47A, pp.2674-8510.1007/s11661-016-3433-7 ↗
19. O. Grässel, L. Krüger, G. Frommeyer, and L.W. Meyer: International Journal of Plasticity, 2000, vol. 16, pp. 1391-140910.1016/S0749-6419(00)00015-2 ↗
20. B.C. De Cooman, P. Gibbs, S. Lee, and D.K. Matlock: Met Trans A, 2013, vol. 44A, pp. 2563-7210.1007/s11661-013-1638-6 ↗
21. D.M. Field and D.C. Van Aken: Metall. Mater. Trans. A, 2018, vol. 49A, pp. 1152–6610.1007/s11661-018-4481-y ↗
22. S.T. Pisarik, D.C. Van Aken, K. Limmer, and J.E. Medvedeva: AISTech 2014 Proceedings, 2014, vol. III, pp. 3013–23
23. S.K. Huang, Y.H. Wen, N.Li, J.Teng, S.Ding, Y.G. Xu: Mater Characterization vol.59, 2008, pp.681-8710.1016/j.matchar.2007.05.023 ↗
24. S. Shin, M. Kwon, W. Cho, I. S. Suh, and B.C. De Cooman: Mater. Sci. & Eng. 2017, vol. 683, pp. 187-9410.1016/j.msea.2016.10.079 ↗
25. M.C. McGrath, D.C. Van Aken, N.I. Medvedeva, and J.E. Medvedeva: Metall. Mater. Trans. A, Vol. 44A, 2013, pp. 4634-43.10.1007/s11661-013-1820-x ↗
26. X.-S. Yang, S. Sun, H.-H. Ruan, S.-Q. Shi, and T.-Y. Zhang: Acta Mater., 2017, vol. 136, pp. 347–5410.1016/j.actamat.2017.07.016 ↗
27. D.C. Van Aken, S.T. Pisarik, and M.C. McGrath: Proceedings of the International Symposium on New Developments in Advanced High-Strength Steels, Vail, Colorado, 2013, pp. 119–29.
28. D. M. Field, and D.C. Van Aken: Met Trans A., (2016) Vol. 47A pp.1912-1710.1007/s11661-016-3394-x ↗
29. N.I. Medvedeva, M.S. Park, D.C. Van Aken, and J.E. Medvedeva: J. Alloys Compd., Vol. 582, 2014, pp. 475–8210.1016/j.jallcom.2013.08.089 ↗
30. K.R. Limmer, J.E. Medvedeva, D.C. Van Aken and N.I. Medvedeva: Comput. Mater. Sci., 2015, vol. 99, pp. 253–5510.1016/j.commatsci.2014.12.015 ↗
31. S.T. Pisarik and D.C. Van Aken: Met Trans A., Vol. 47A 2016 pp1009-101810.1007/s11661-015-3265-x ↗
32. D.M. Field, D.S. Baker, and D.C. Van Aken: Metall. Mater. Trans. A, 2017, vol. 48A, pp. 2150–6310.1007/s11661-017-4020-2 ↗
33. P.P. Suikkanen, V.T.E. Lang, M.C.Somani, D.A. Prter, and L.P. Karjalainen: ISIJ International, 2012, vol. 52, pp. 471-7610.2355/isijinternational.52.471 ↗
34. Z, Li-Juan, W. Di, and Z. Xian-ming: Jour. Iron and Steel research international, 2007, vol. 14, pp. 61-65
35. L.J. Zhu, D. Wu, X.M. Zhao: Acta Metall. 2008 vol. 21, pp. 163-6810.1016/S1006-7191(08)60034-4 ↗
36. M.C. Somani, L.P. Karjalainenm, D.A. Porter, and R.A. Morgridge: Proceedings of International Conference on Thermomechanical Processing Mechanics: Microstructures and Controls, University of Sheffield, Sheffield GB, (2003), 436.
37. S.F. Medina, and J. E. Mancilla: ISIJ Int. 1996, vol. 36, pp.1036-107010.2355/isijinternational.36.1036 ↗
38. S.F. Medina, and A. Quispe: ISIJ Int. 2001, vol. 41, pp.774-8010.2355/isijinternational.41.774 ↗
39. S-J. Lee, J. Kim, S.N. Kane, and B.C. De Cooman: Acta Materialia, 2011, vol. 59, pp.6809-1910.1016/j.actamat.2011.07.040 ↗
40. S.J. Lee, S.W. Lee, B.C. De Cooman: Int. J. Mater. Res., 2013, vol. 104, pp. 423–29.10.3139/146.110882 ↗
41. G.B. Olson, M. Cohen: Met Trans A Vol 7 1976 pp. 1897-1904
42. ASTM E 8/E 8M-08, Standard Test Methods for Tension Testing of Metallic Materials
43. S. Martin, C. Ullrich, D. Simek, U. Martin, and D. Rafaja: J. Appl. Crystallogr., 2011, vol. 44, pp. 779-8710.1107/S0021889811019558 ↗
44. N. Stanford and D.P. Dunne: Acta Materialia, 2010, Vol. 58, pp.6752-6210.1016/j.actamat.2010.08.041 ↗
45. S. T. Pisarik, and D. C. Van Aken: Met Trans A., 2014, vol. 45, pp. 3173-7810.1007/s11661-014-2303-4 ↗
46. M. Papa Rao, V. Subramanya Sarma, and S. Sankaran: Met. Trans. A 2014, vol 45A pp. 5313–1710.1007/s11661-014-2478-8 ↗
47. M. Papa Rao, V. Subramanya Sarma, and S. Sankaran: Mater. Sci. & Eng. A 2013, vol. 568 pp. 171–75
48. O. Saray, G. Purcek, I. Karaman, H. Maier: Met Trans A 2012, vol. 43A. 4320–3010.1007/s11661-012-1238-x ↗
49. V.S.A. Challa, R.D.K. Misra, M.C. Comani and Z.D. Wang: Mater. Sci. & Eng 2016 vol. 661 pp.51–6010.1016/j.msea.2016.03.002 ↗
50. Y. Son, Y.K. Lee, K.-T. Park, C. S. Lee, and D. H. Shin: Acta Mater. 2005, vol. 53, pp. 3125–3410.1016/j.actamat.2005.02.015 ↗
51. M. Calcagnotto, Y. Adachi, D. Ponge, and D. Raabe: Acta Meter. 2011, vol. 59 pp. 658–7010.1016/j.actamat.2010.10.002 ↗
52. D. H. Shin, and K-T. Park: Mater. Sci. & Eng. A 2005, vol. 410-411, pp. 299-30210.1016/j.msea.2005.08.025 ↗
53. M. Calcagnotto, D. Ponge, E. Demir, and D. Raabe: Mater. Sci. & Eng. A 2010 vol. 527, pp. 2738-4610.1016/j.msea.2010.01.004 ↗
54. R.D.K. Misra, P.K.C. Vankatsurya, M.C. Somani, and L.P. Karjalinen: Met Trans A, 2012, vol. 43A, pp. 5286-9710.1007/s11661-012-1360-9 ↗
55. P.J. Gibbs, E. De Moor, M.J. Merwin, B. Clausen, J.G. Speer, and D.K. Matlock: Met Trans A, 2011, vol. 42A, pp. 3691-370110.1007/s11661-011-0687-y ↗
56. G. Dini, A. Najafizadeh, R. Ueji, and S.M. Monir-Vaghefi: Materials Letters, 2010, vol. 64, pp. 15-1810.1016/j.matlet.2009.09.057 ↗
57. S. Rajasekhara, P.J. Ferreira, L.P. Karjalainenm and A. Kyröläinen: Met Trans A. 2007, vol. 38A, pp. 1202–121010.1007/s11661-007-9143-4 ↗
58. A. Rohatgi, K.S., Vecchio, and G.T. Gray III: Met. Trans. A, 2001, vol. 32A, pp. 135–4510.1007/s11661-001-0109-7 ↗
59. D.J. Branagan, C.S. Parsons, T.V. Machrowicz, A.E. Frerichs, B.E. Meacham, S. Cheng, and A.V. Sergueeva 2016, Launch of a New Class of 3 rd Generation Cold Formable AHSS [PowerPoint slide 15 & 16]