Effects of Cu and Si Contents on the Fluidity, Hot Tearing, and Mechanical Properties of Al-Cu-Si Alloys
Source abstract
Abstract
The effects of the Cu and Si contents on the fluidity, hot tearing, and mechanical properties of Al-Cu-Si alloys were investigated to evaluate the castability of these widely used forged alloys. Al-Cu-Si alloys with 3.5, 4.5, and 5.5 wt pct Cu and 0, 1.5, and 3.0 wt pct Si were cast at 700 °C in spiral and hot tearing test molds to determine the fluidity and hot tearing characteristics, respectively. With a higher Cu content, the fluidity length decreased by 4.9 and 14 pct, but the hot tearing susceptibility increased from 0.44 to 0.56 and 0.67. With a higher Si content at a fixed Cu content of 4.5 wt pct, the fluidity length increased by 11 pct, and hot tearing was not observed. A solid solution heat treatment was performed at 515 °C for 2 hours and at 525 °C for 8 hours, and the alloy was then quenched in water. Artificial aging was carried out at 185 °C for times of 4, 6, 8, and 10 hours. To improve the fluidity and mechanical properties, 0.10 wt pct Ti was added as a grain refiner. The fluidity increased by 4.6 pct, and the tensile strength increased by 339 MPa.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Bauxite Residue and Utilization
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (39)
Show source-provided references
1. J.R. Davis, A.S.M. Specialty, Handbook: Aluminum and Aluminum Alloys, ASM International, Cleveland, OH, 1993.
2. B.H. Choi, Y.S. Jang, J.G. Sim, H.S. Kim, C.P. Hong, ISIJ Int., 2013, vol. 53, pp. 502-510.10.2355/isijinternational.53.502 ↗
3. M.A. El-Sayed, H. Hassanin, K. Essa, Int. J. Cast Met. Res., 2016, vol. 29, pp. 350-354.10.1080/13640461.2016.1145966 ↗
4. M.K. Karbalaei Akbari, H.R. Baharvandi, K. Shirvanimoghaddam, Mater. Des., 2015, vol. 66, pp. 150-161.10.1016/j.matdes.2014.10.048 ↗
5. S.A. Sajjadi, H.R. Ezatpour, H. Beygi, Mater. Sci. Eng. A, 2011, vol. 528, pp. 8765-8771.10.1016/j.msea.2011.08.052 ↗
6. S.W. Choi, H.S. Cho, S. Kumai, J. Alloy Compd., 2016, vol. 688, pp. 897-902.10.1016/j.jallcom.2016.07.137 ↗
7. S. Esmaeili, X. Wang, D.J. Lloyd, W.J. Poole, Metall. Mater. Trans. A, 2003, vol. 34, pp. 751-763.
8. M.C. Flemings, Casting Processing, McGraw-Hill Inc., New York, 1974.
9. M.D. Di Sabatino, L. Arnberg, Trans. Indian Inst. Met., 2009, vol. 62, pp. 321-325.10.1007/s12666-009-0049-2 ↗
10. K.R. Ravi, R.M. Pillai, K.R. Amaranathan, B.C. Pai, M. Chakraborty, J. Alloy Compd., 2008, vol. 456, pp. 201-210.10.1016/j.jallcom.2007.02.038 ↗
11. G. Timelli, D. Caliari, Mater. Sci. Forum, 2017, vol. 884, pp. 71-80.10.4028/www.scientific.net/MSF.884.71 ↗
12. G. Timelli, F. Bonollo: Int. J. Cast Met. Res., 2007, vol. 20, pp. 304–311.10.1179/136404608X286110 ↗
13. D. Caliari, G. Timelli, F. Bonollo, P. Amalberto, P. Giordano: Metall. Ital., 2015, vol. 107, pp. 11–18.
14. A.K. Dahle, P.A. Tondel, C.J. Paradies, L. Arnberg, Metall. Mater. Trans. A, 1996, vol. 27, pp. 2305-2313.10.1007/BF02651885 ↗
15. S. Li, K. Sadayappan, D. Apelian: Int. J. Cast Met. Res., 2011, vol. 24, pp. 88–95.10.1179/1743133610Y.0000000004 ↗
16. W.H. Suyitno, L. Kool, Katgerman, Metall. Mater. Trans. A, 2005, vol. 36A, pp. 1537-1546.10.1007/s11661-005-0245-6 ↗
17. D.G. Eskin, L. Suyitno, L. Katgerman, Prog. Mater. Sci., 2004, vol. 49, pp. 629-711.10.1016/S0079-6425(03)00037-9 ↗
18. L. Lu, A.K. Dahle, C. Davidson, D. StJohn, TMS Light Met., 2007.
19. S. Samavedam, S. Sundarrajan, Arch. Foundry Eng., 2016, vol. 16, pp. 61–68.10.1515/afe-2016-0004 ↗
20. Y. Awano, K. Morimoto, Int. J. Cast Met. Res., 2004, vol. 17, pp. 107–114.10.1179/136404604225014846 ↗
21. L. Bichler, A. Elsayed, K. Lee, C. Ravindran, Int. J. Met., 2008, vol. 2, pp. 43–54.
22. M.R. Nasresfahani, B. Niroumand: Metall. Mater. Trans. A, 2014, vol. 45, pp. 3699–3702.10.1007/s11661-014-2341-y ↗
23. M. Rappaz, J. Drezet, M. Gremaud, Metall. Mater. Trans. A, 1999, vol. 30, pp. 449–455.10.1007/s11661-999-0334-z ↗
24. M. Bagheri, M. Alizadeh, A.R. Ahmadi, Metall. Mater. Trans. A, 2017, vol. 48, pp. 1856–1863.10.1007/s11661-017-3993-1 ↗
25. M.R.N. Esfahani, B. Niroumand, Mater. Charact., 2010, vol. 61, pp. 318-324.10.1016/j.matchar.2009.12.015 ↗
26. C. Davidson, D. Viano, L. Lu, D. StJohn, Int. J. Cast Met. Res., 2006, vol. 19, pp. 59-65.10.1179/136404606225023291 ↗
27. M. Zeren, J. Mater. Proc. Tech., 2005, vol. 169, pp. 292-298.10.1016/j.jmatprotec.2005.03.009 ↗
28. D.H. Xiao, J.N. Wang, D.Y. Ding, S.P. Chen, J. Alloy Compd., 2002, vol. 343, pp. 77-81.10.1016/S0925-8388(02)00076-2 ↗
29. S.C. Wang, M.J. Starink, N. Gao, Scr. Mater., 2006, vol. 54, pp. 287-291.10.1016/j.scriptamat.2005.09.010 ↗
30. Y.J. Gao, X.H. Hou, Q.F. Mo, C.Y. Wei, X.B. Qin, J. Alloy Compd., 2007, vol. 441, pp. 241-245.10.1016/j.jallcom.2006.09.088 ↗
31. B.S. Murty, S.A. Kori, M. Chakraborty, Int. Mater. Rev., 2002, vol. 47, pp. 3-29.10.1179/095066001225001049 ↗
32. Y. Li, Q.L. Bai, J.C. Liu, H.X. Li, Q. Du, J.S. Zhang, L.Z. Zhuang, Metall. Mater. Trans. A, 2016, vol. 47, pp. 4024–4037.10.1007/s11661-016-3543-2 ↗
33. M. Easton, D. St. John, Metall. Mater. Trans. A, 1999, vol. 30, pp. 1613–23.10.1007/s11661-999-0098-5 ↗
34. Q.L. Bai, Y. Li, H.X. Li, Q. Du, J.S. Zhang, L.Z. Zhuang, Metall. Mater. Trans. A, 2016, vol. 47, pp. 4080–4091.10.1007/s11661-016-3588-2 ↗
35. C.J. Tseng, S.L. Lee, S.C. Tsai, C.J. Cheng, J. Mater. Res., 2002, vol. 17, pp. 2243-2250.10.1557/JMR.2002.0330 ↗
36. J. Campbell, Castings, Heinemann, Butterworth, Oxford, 2003.
37. American Society for Metals, Metals Handbook, 8th ed., Vol. 1, ASM International, Cleveland, OH, 1979.
38. J. J. Valencia, P. N. Quested, ASM Handb. Cast., 2008, vol. 15, pp. 468–481.10.31399/asm.hb.v15.a0005240 ↗
39. G.E. Dieter: Mechanical Metallurgy, International Student ed., McGraw-Hill, New York, 1961, pp. 204–09.10.5962/bhl.title.35895 ↗