SEM/EBSD Analysis on Globularization Behavior of Lamellar Microstructure in Ti-6Al-4V During Hot Deformation and Annealing
Source abstract
Abstract
Scanning electron microscope/electron back-scattering diffraction was used to investigate local misorientation development within an individual α plate of a Ti-6Al-4V alloy with an α lamellar microstructure during hot deformation at 1223 K (950 °C) and a strain rate of 0.1 s−1. The correlation between the local misorientation development and the globularization behavior of α plates during subsequent annealing at 1223 K (950 °C) was discussed. The misorientation profile along an individual α plate showed that not only a continuous and smooth change in orientation but also a discontinuous change in orientation was developed by the hot deformation. We assume that the points where discontinuous change in orientation occurs, P d, became α/α boundaries and resulted in splitting α plates the annealing. The mean length between adjacent discontinuous points, L I, was determined and compared with the actual mean length of the α plates after hot deformation and subsequent annealing, L a, as measured by optical microscopy. The two kinds of length parameters coincided at lower strains, but significant differences were observed at higher strains, i.e., L I was larger than L a. Further analysis showed that rotation axes (R.A.s) changed even within regions where orientation changes were continuous. By taking into account the points where the R.A.s changed, P r and P d, the mean length between adjacent points, L II, appeared to coincide with L a at higher strains. A higher lattice distortion is expected near points P r at higher strains, which results in the formation of new α/α boundaries in subsequent annealing. Consequently, points P d already developed by hot deformation were considered to become α/α boundaries and led to splitting α plates in annealing. New α/α boundaries formed at points P r in subsequent annealing after a higher strain deformation, which led to a splitting of α plates as well.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Titanium Alloys Microstructure and Properties · Intermetallics and Advanced Alloy Properties · Metallurgy and Material Forming
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (15)
Show source-provided references
1. R.R. Boyer: Mater. Sci. Eng. A, 1996, vol. A213, pp. 103–14.10.1016/0921-5093(96)10233-1 ↗
2. C. Leyens and M. Peters: Titanium and Titanium Alloys, Wiley-VCH, Weinheim, 2003.10.1002/3527602119 ↗
3. I. Weiss, G.E. Welsch, F.H. Froes, and D. Eylon: in Titanium: Science and Technology, G. Luetjering, U. Zwicker, and W. Bunk, eds., Deutsche Gesellschaft fur Metallkunde, Oberursel, 1985, pp. 1503–10.
4. I. Weiss, F.H. Froes, D. Eylon, and G.E. Welsch: Metall. Mater. Trans. A, 1986, vol. 17A, pp. 1935–47.10.1007/BF02644991 ↗
5. S.L. Semiatin, V. Seetharaman, and I. Weiss: Mater. Sci. Eng. A, 1999, vol. A263, pp. 257–71.10.1016/S0921-5093(98)01156-3 ↗
6. E.B. Shell and S.L. Semiatin: Metall. Mater. Trans. A, 1999, vol. 39A, pp. 3219–29.10.1007/s11661-999-0232-4 ↗
7. N. Stefansson, S.L. Semiatin, and D. Eylon: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 3527–34.10.1007/s11661-002-0340-x ↗
8. N. Stefansson and S.L. Semiatin: Metall. Mater. Trans. A, 2003, vol. 34A, pp. 691–98.10.1007/s11661-003-0103-3 ↗
9. S.L. Semiatin and D.U. Furrer: in ASM Handbook. Fundamental of Modeling for Metals Processing, S.L. Semiatin and D.U. Furrer, eds., ASM International, Materials Park, 2009, vol. 22, pp. 522–35.10.31399/asm.hb.v22a.a0005409 ↗
10. T.R. Bieler and S.L. Semiatin: Int. J. Plast., 2002, vol. 18, pp. 1165–89.10.1016/S0749-6419(01)00057-2 ↗
11. T. Furuhara, H. Abe, B. Poorganji, and T. Maki: in Ti-2007: Science and Technology, M. Ninomi, S. Akiyama, M. Ikeda, M. Hagiwara, and K. Maruyama, eds., The Japan Institute of Metals, Kyoto, 2007, pp. 913–19.
12. T. Furuhara, B. Poorganji, H. Abe, and T. Maki: JOM, 2002, January, pp. 64–67.
13. G. Lutjering and J.C. Williams: Titanium, 2nd ed., Springer, Berlin, 2007.
14. S. Mironov, M. Murzinova, S. Zherebtsov, G.A. Salishchev, and S.L. Semiatin: Acta Mater., 2009, vol. 57, pp. 2470–81.10.1016/j.actamat.2009.02.016 ↗
15. N. Hansen: Metall. Mater. Trans. A, 2001, vol. 32A, pp. 2917–35.10.1007/s11661-001-0167-x ↗