journal article·2018-08Open access

A Combined Precipitation, Yield Stress, and Work Hardening Model for Al-Mg-Si Alloys Incorporating the Effects of Strain Rate and Temperature

Ole Runar Myhr, Odd Sture Hopperstad, Tore Børvik

Abstract

In this study, a combined precipitation, yield strength, and work hardening model for Al-Mg-Si alloys known as NaMo has been further developed to include the effects of strain rate and temperature on the resulting stress–strain behavior. The extension of the model is based on a comprehensive experimental database, where thermomechanical data for three different Al-Mg-Si alloys are available. In the tests, the temperature was varied between 20 °C and 350 °C with strain rates ranging from 10−6 to 750 s−1 using ordinary tension tests for low strain rates and a split-Hopkinson tension bar system for high strain rates, respectively. This large span in temperatures and strain rates covers a broad range of industrial relevant problems from creep to impact loading. Based on the experimental data, a procedure for calibrating the different physical parameters of the model has been developed, starting with the simplest case of a stable precipitate structure and small plastic strains, from which basic kinetic data for obstacle limited dislocation glide were extracted. For larger strains, when work hardening becomes significant, the dynamic recovery was linked to the Zener-Hollomon parameter, again using a stable precipitate structure as a basis for calibration. Finally, the complex situation of concurrent work hardening and dynamic evolution of the precipitate structure was analyzed using a stepwise numerical solution algorithm where parameters representing the instantaneous state of the structure were used to calculate the corresponding instantaneous yield strength and work hardening rate. The model was demonstrated to exhibit a high degree of predictive power as documented by a good agreement between predictions and measurements, and it is deemed well suited for simulations of thermomechanical processing of Al-Mg-Si alloys where plastic deformation is carried out at various strain rates and temperatures.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Microstructure and mechanical properties · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (54)

Show source-provided references
1. G. Edwards, K. Stiller, G. Dunlop, and M. Couper: Acta Mater., 1998, vol. 46, pp. 3893-04.10.1016/S1359-6454(98)00059-7 ↗
2. M. Murayama, K. Hono, M. Saga, and M. Kikuchi: Mater. Sci. Eng. A, 1998, vol. 250, pp. 127-32.10.1016/S0921-5093(98)00548-6 ↗
3. I. Dutta, and S.M. Allen: J. Mater. Sci. Lett., 1991, vol. 10, pp. 323-26.10.1007/BF00719697 ↗
4. W.F. Miao and D.E. Laughlin: Scripta Mater., 1999, vol. 40, pp. 873-78.10.1016/S1359-6462(99)00046-9 ↗
5. C.D. Marioara, S.J. Andersen, J. Jansen, and H.W. Zandbergen: Acta Mater., 2001, vol. 49, pp. 321–28.10.1016/S1359-6454(00)00302-5 ↗
6. J.S. Langer and A.J. Schwartz: Physical Review A, The American Physical Society, 1980, vol. 21, pp. 948-958.10.1103/PhysRevA.21.948 ↗
7. R. Kampmann, H. Eckerlebe, and R. Wagner: Mat. Res. Soc. Symp. Proc., MRS, 1987, vol. 57, pp. 525–42.
8. R. Wagner and R. Kampmann: Material Science and Technology—A Comprehensive Treatment, vol. 5, VCH, 1991, pp. 213–303.
9. A. Bahrami, A. Miroux, and J. Sietsma: Metall. Mater. Trans. A, 2012, vol. 43A, pp. 4445-53.10.1007/s11661-012-1211-8 ↗
10. D. Bardel, M. Perez, D. Nelias, A. Deschamps, C. R. Hutchinson, D. Maisonnette, T. Chaise, J. Gamier, and F. Bourlier: Acta Mater., 2014, vol. 62, pp. 129-140.10.1016/j.actamat.2013.09.041 ↗
11. Q. Du, B. Holmedal, J. Friis, and C. Marioara: Metall. Mater. Trans. A, 2016, vol. 47A, pp. 589-599.10.1007/s11661-015-3196-6 ↗
12. Q. Du, K. Tang, C.D. Marioara, S.J. Andersen, B. Holmedal, and R. Holmestad: Acta Mater., 2017, vol. 122, pp. 178-186.10.1016/j.actamat.2016.09.052 ↗
13. M. Perez, M. Dumont, and D. Acevedo-Reyes: Acta Mater., 2008, vol. 56, pp. 2119-32.10.1016/j.actamat.2007.12.050 ↗
14. Q. Du, Y. Li: Acta Mater. 2014, vol. 71, pp. 380-389.10.1016/j.actamat.2014.03.028 ↗
15. P. Maugis, M. Goune: Acta Mater. 2005, vol. 53, pp. 3359-67.10.1016/j.actamat.2005.03.036 ↗
16. Q. Du, W.J. Poole, M.A. Wells: Acta Mater., 2012, vol. 60, pp. 3830-39.10.1016/j.actamat.2012.02.050 ↗
17. Q. Chen, J. Jeppsson, J. Ågren: Acta Mater., 2008, vol. 56, pp. 1890-96.10.1016/j.actamat.2007.12.037 ↗
18. E. Kozeschnik, I. Holzer, B. Sonderegger: J. Phase Equilibria Diffusion, 2007, vol. 28, pp. 64-71.10.1007/s11669-006-9003-8 ↗
19. A. Deschamps and Y. Bréchet: Acta Mater. 1999, vol. 47, pp. 293-305.10.1016/S1359-6454(98)00296-1 ↗
20. O.R. Myhr, Ø. Grong, and S.J. Andersen: Acta Mater., 2001, vol. 49, pp. 65-75.10.1016/S1359-6454(00)00301-3 ↗
21. L.M Cheng, W.J. Poole, J.D. Embury, and D.J. Lloyd: Metall. Mater. Trans. A, 2003, vol. 34A, pp. 2473-81.10.1007/s11661-003-0007-2 ↗
22. W.J. Poole and D.J. Lloyd: Proc. 9th Int. Conf. on Aluminium Alloys, Institute of Materials Engineering Australasia Ltd, 2004, pp. 939–44.
23. U.F. Kocks: J. Eng. Mater. Technol., 1976, vol. 98, pp. 76-85.10.1115/1.3443340 ↗
24. H. Mecking and U.F. Kocks: Acta Metall., 1981, vol. 29, pp. 1865-75.10.1016/0001-6160(81)90112-7 ↗
25. Y. Estrin: in Unified Constitutive Laws of Plastic Deformation, A.S. Krausz and K. Krausz, eds., Academic Press, New York, NY, 1996, pp. 69–106.10.1016/B978-012425970-6/50003-5 ↗
26. Y. Estrin: J. of Mater. Proc. Technol., 1998, vols. 80-81, pp. 33-39.10.1016/S0924-0136(98)00208-8 ↗
27. H. J. Frost, and M. F. Ashby: Deformation-Mechanism Maps. The Plasticity and Creep of Metals and Ceramics, Oxford (England), Pergamon Press, 1982.
28. A.G. Evans and R.D. Rawlings: Phys. Stat. Sol., 1969, vol. 34, pp. 9-31.10.1002/pssb.19690340102 ↗
29. Y. Bergström, H. Hallén: Mater. Sci. Eng., 1982, vol. 55, pp. 49-61.10.1016/0025-5416(82)90083-0 ↗
30. A.H. van den Boogaard and J. Huétink: Comput. Methods Appl. Mech. Engrg., 2006, vol. 195, pp. 6691-6709.10.1016/j.cma.2005.05.054 ↗
31. O.R. Myhr, Ø. Grong and C. Schäfer: Metall. Mater. Trans A, 2015, vol. 46A, pp. 6018-39.10.1007/s11661-015-3175-y ↗
32. O.R. Myhr, Ø. Grong, and K.O. Pedersen: Metall. Mater. Trans. A, 2010, vol. 41A, pp. 2276-89.10.1007/s11661-010-0258-7 ↗
33. O.R. Myhr, and Ø. Grong: Acta Mater., 2000, vol. 48, pp. 1605-15.10.1016/S1359-6454(99)00435-8 ↗
34. O.R. Myhr and Ø. Grong: ASM Handbook, Welding Fundamentals and Processes, ASM, vol. 6A, 2011, pp. 797–18.
35. O.R. Myhr, Ø. Grong, H.G. Fjær and C.D. Marioara: Acta Mater., 2004, vol. 52, pp. 4997-08.10.1016/j.actamat.2004.07.002 ↗
36. J.K. Holmen, T. Børvik, O.R. Myhr, H.G. Fjær, O.S. Hopperstad: International Journal of Impact Engineering, 2015, vol. 84, pp. 96-107.10.1016/j.ijimpeng.2015.05.016 ↗
37. J. Johnsen, J.K. Holmen, O.R. Myhr, O.S. Hopperstad, T. Børvik: Comp. Mat. S., 2013, vol. 79, pp. 724-735.10.1016/j.commatsci.2013.07.035 ↗
38. C. Dørum, O.G. Lademo, O.R. Myhr, T. Berstad, O.S. Hopperstad: Computers & Structures, 2010, vol. 88, pp. 519–528.10.1016/j.compstruc.2010.01.003 ↗
39. A.J.E. Foreman and M.J. Makin: Phil. Mag., 1966, vol. 14, pp. 911-924.10.1080/14786436608244762 ↗
40. L.M. Brown and R.K. Ham: in Strengthening Methods in Crystals. A. Kelly and R.B. Nicholson, eds., Applied Science Publishers Ltd., Academic Press, London, 1971, pp. 9–135.
41. A.J. Ardell: Metall. Mater. Trans. A, 1985, vol. 61A, pp. 2131-65.10.1007/BF02670416 ↗
42. U.F. Kocks: Phil.Mag., 1966, vol. 13, pp. 541-66.10.1080/14786436608212647 ↗
43. A. Rusinek, J.A. Rodríguez-Martínez: Materials & Design, 2009, vol. 30, pp. 4377-90.10.1016/j.matdes.2009.04.011 ↗
44. K. Teichmann, C.D. Marioara, S.J. Andersen, and K. Martinsen: Metall. Mater. Trans. A, 2012, vol. 43A, pp. 4006-14.10.1007/s11661-012-1235-0 ↗
45. K. Teichmann, C.D. Marioara, S.J. Andersen, and K. Martinsen: Materials Characterization, 2013, vol. 75, pp. 1-7.10.1016/j.matchar.2012.10.003 ↗
46. F. Fazeli, C.W. Sinclair, and T. Bastow: Metall. Mater. Trans. A, 2008, vol. 39A, pp. 2297-2305.10.1007/s11661-008-9587-1 ↗
47. M. F. Ashby (1970) Phil. Mag. J., vol. 21, pp. 399-424.10.1080/14786437008238426 ↗
48. S. Gouttebroze, A. Mo, Ø. Grong, K.O. Pederesen and H.G. Fjær: Metall. Mater. Trans. A, 2008, vol. 39A, pp. 522-534.10.1007/s11661-007-9443-8 ↗
49. V. Vilamosa, A.H. Clausen, T. Børvik, S.R. Skjervold, O.S. Hopperstad: Int. Journal of Impact Engineering, 2015, vol. 86, pp. 223-239.10.1016/j.ijimpeng.2015.08.008 ↗
50. U.F. Kocks, A.S. Argon, and M.F. Ashby: Thermodynamics and Kinetics of Slip, Progress in Materials Science, vol.19, Pergamon, Oxford (England), 1975.
51. V. Vilamosa, A.H. Clausen, T. Børvik, B. Holmedal, O.S. Hopperstad: Materials & Design, 2016, vol. 103, pp. 391-405.10.1016/j.matdes.2016.04.047 ↗
52. V. Vilamosa, A.H. Clausen, E. Fagerholt, O.S. Hopperstad and T. Børvik: Strain, 2014, vol. 50, pp. 223-235.10.1111/str.12084 ↗
53. V. Vilamosa: Doctoral Thesis, Norwegian University of Science and Technology, Department of Structural Engineering, Trondheim, 2015.
54. H.G. Fjær, B.I. Bjørneklett, and O.R. Myhr: Proc. TMS Annual Meeting, San Francisco, CA, Feb. 2005, TMS, Warrendale, PA, 2005, pp. 95–100.