journal article·2017-11Open access

The Effect of Ultrasonic Melt Treatment on Macro-Segregation and Peritectic Transformation in an Al-19Si-4Fe Alloy

C. J. Todaro, M. A. Easton, D. Qiu, G. Wang, D. H. StJohn, M. Qian

Abstract

It is well documented that ultrasonic melt treatment (USMT) can refine dendritic and eutectic microstructures during solidification, but much less attention has been paid to the effect of USMT on macro-segregation and intermetallic transformations. In this research, macro-segregation and primary Fe-containing intermetallic peritectic transformations in an Al-19 wt pct Si-4 wt pct Fe alloy were investigated without and with USMT. Macrostructural examination showed that in the absence of USMT the ingot revealed considerable non-uniform distribution of both the primary Fe-containing intermetallic and primary Si particles, whereas the ingot with USMT exhibited near homogeneous distribution of both primary phases, i.e., reduced macro-segregation. The beneficial effect of USMT on relieving macro-segregation was further examined using quantitative microstructural metallography and the results indicated that the area fraction, number density, and size distribution of both primary phases became essentially uniform across the ingot after USMT. USMT further exerted a significant impact on the constitution of the primary Fe-containing intermetallics, where complex particles of delta-Al3FeSi2/beta-Al5FeSi were prominent without USMT, while few delta-Al3FeSi2 particles were observed after USMT and the primary Fe-containing intermetallics existed mostly as the single-phase beta-Al5FeSi. The underlying reason was attributed to the reduction in the size of the primary delta-Al3FeSi2 particles which ensures the complete transformation of most primary delta-Al3FeSi2 particles to the peritectic beta-Al5FeSi phase.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Intermetallics and Advanced Alloy Properties · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (54)

Show source-provided references
1. 1. J. Zhou, J. Duszczyk and B. M. Korevaar: J. Mater. Sci., 1991, vol. 26, pp. 3041-50.10.1007/BF01124840 ↗
2. 2. T.S. Kim, C. Suryanarayana and B.S. Chun: Mater. Sci. Eng. A, 2000, vol. 278, pp. 113-20.10.1016/S0921-5093(99)00589-4 ↗
3. 3. L. Wang, M. Makhlouf and D. Apelian: Int. Mater. Rev., 1995, vol. 40, pp. 221-38.10.1179/imr.1995.40.6.221 ↗
4. 4. N. Tenekedjiev, D. Argo and J. E. Gruzleski: AFS Trans., 1989, vol. 97, pp. 127-36.
5. 5. M. Rajabi, M. Vahidi, A. Simchi and P. Davami: Mater. Charact., 2009, vol. 60, pp. 1370-81.10.1016/j.matchar.2009.06.014 ↗
6. 6. H. J. Huang, Y. H. Cai, H. Cui, J. F. Huang, J. P. He and J. S. Zhang: Mater. Sci. Eng. A, 2009, vol. 502, pp. 118-25.10.1016/j.msea.2008.10.005 ↗
7. Q. L. Wang, H. R. Geng, S. Zhang, H. W. Jiang and M. Zuo: Metall. Mater. Trans. A, 2014, vol. 4A, pp. 1621-30.10.1007/s11661-013-2081-4 ↗
8. 8. Y. Osawa, S. Takarnori, T. Kimura, K. Minagawa and H. Kakisawa: Mater. Trans., 2007, vol. 48, pp. 2467-75.10.2320/matertrans.F-MRA2007874 ↗
9. 9. G. Zhong, S. S. Wu, H. W. Jiang and P. An: J. Alloy. Compd., 2010, vol. 492, pp. 482-87.10.1016/j.jallcom.2009.11.145 ↗
10. 10. M. Sha, S. S. Wu and L. Wan: Mater. Sci. Eng. A, 2012, vol. 554, pp. 142-48.10.1016/j.msea.2012.06.026 ↗
11. 11. C. Lin, S. S. Wu, S. L. Lu and P. An: J. Alloy. Compd., 2013, vol. 568, pp. 42-48.10.1016/j.jallcom.2013.03.089 ↗
12. 12. C. Lin, S. S. Wu, S. L. Lu, P. An and L. Wan: Intermetallics, 2013, vol. 32, pp. 176-83.10.1016/j.intermet.2012.09.001 ↗
13. W. Khalifa, S. El-Hadad and Y. Tsunekawa: Metall. Mater. Trans. A, 2013, vol. 44A, pp. 5817-24.10.1007/s11661-013-1936-z ↗
14. 14. L. F. Mondolfo: Aluminum Alloys: Structure and Properties, Butterworths, London, 1976.
15. W. Khalifa, F. H. Samuel and J. E. Gruzleski: Metall. Mater. Trans. A, 2003, vol. 34, pp. 807-25.10.1007/s11661-003-1009-9 ↗
16. 16. M. H. Mulazimoglu, A. Zaluska, J. E. Gruzleski and F. Paray: Metall. Mater. Trans. A, 1996, vol. 27, pp. 929-36.10.1007/BF02649760 ↗
17. 17. G. Sha, K. A. Q. O’Reilly, B. Cantor, J. M. Titchmarsh and R. G. Hamerton: Acta Mater., 2003, vol. 51, pp. 1883-97.10.1016/S1359-6454(02)00595-5 ↗
18. 18. O. V. Abramov: Ultrasound in liquid and solid metals, CRC Press, Boca Raton, FL, 1994.
19. 19. G. I. Eskin and D. G. Eskin: Ultrasonic Treatment of Light Alloy Melts, 2nd ed., CRC Press, Boca Raton, FL, 2014.10.1201/b17270 ↗
20. 20. A. Ramirez, M. Qian, B. Davis, T. Wilks and D. H. StJohn: Scripta Mater., 2008, vol. 59, pp. 19-22.10.1016/j.scriptamat.2008.02.017 ↗
21. 21. M. Qian, A. Ramirez and A. Das: J. Cryst. Growth, 2009, vol. 311, pp. 3708-15.10.1016/j.jcrysgro.2009.04.036 ↗
22. 22. M. Qian, A. Ramirez, A. Das and D. H. StJohn: J. Cryst. Growth, 2010, vol. 312, pp. 2267-72.10.1016/j.jcrysgro.2010.04.035 ↗
23. T. V. Atamanenko, D. G. Eskin, L. Zhang and L. Katgerman: Metall. Mater. Trans. A, 2010, vol. 41A, pp. 2056-66.10.1007/s11661-010-0232-4 ↗
24. 24. G. Wang, M. S. Dargusch, M. Qian, D. G. Eskin and D. H. StJohn: J. Cryst. Growth, 2014, vol. 408, pp. 119-24.10.1016/j.jcrysgro.2014.09.018 ↗
25. 25. N. Srivastava, G. P. Chaudhari and M. Qian: J. Mater. Process. Technol., 2017, vol. 249, pp. 367-78.10.1016/j.jmatprotec.2017.06.024 ↗
26. 26. H. R. Kotadia, M. Qian, D. G. Eskin and A. Das: Mater. Design, 2017, vol. 132, pp. 266-74.10.1016/j.matdes.2017.06.065 ↗
27. 27. W. Khalifa, Y. Tsunekawa and M. Okumiya: J. Mater. Process. Technol., 2010, vol. 210, pp. 2178-87.10.1016/j.jmatprotec.2010.08.008 ↗
28. 28. V. O. Abramov, O. V. Abramov, B. B. Straumal and W. Gust: Mater. Design, 1997, vol. 18, pp. 323-26.10.1016/S0261-3069(97)00072-1 ↗
29. 29. G. I. Eskin and D. G. Eskin: Ultrason. Sonochem., 2003, vol. 10, pp. 297-301.10.1016/S1350-4177(02)00158-X ↗
30. 30. H. K. Feng, S. R. Yu, Y. L. Li and L. Y. Gong: J. Mater. Process. Technol., 2008, vol. 208, pp. 330-35.10.1016/j.jmatprotec.2007.12.121 ↗
31. 31. J. B. Ferguson, M. Tabandeh-Khorshid, J. C. Mantas, P. K. Rohatgi, K. Cho and C. S. Kim: Metall. Mater. Trans. B, 2014, vol. 45, pp. 1407-17.10.1007/s11663-014-0044-9 ↗
32. 32. W. Zhai and B. B. Wei: Mater. Lett., 2015, vol. 138, pp. 1-4.10.1016/j.matlet.2014.09.063 ↗
33. 33. W. Zhai, Z. Y. Hong, X. L. Wen, D. L. Geng and B. Wei: Mater. Design, 2015, vol. 72, pp. 43-50.10.1016/j.matdes.2015.02.017 ↗
34. 34. R. Chen, D. Zheng, T. Ma, H. Ding, Y. Su, J. Guo and H. Fu: Ultrason. Sonochem., 2017, vol. 38, pp. 120-33.10.1016/j.ultsonch.2017.03.006 ↗
35. 35. H. R. Kotadia, A. Das, E. Doernberg and R. Schmid-Fetzer: Mater. Chem. Phys., 2011, vol. 131, pp. 241-49.10.1016/j.matchemphys.2011.09.020 ↗
36. 36. W. Zhai, H. M. Liu and B. Wei: Mater. Lett., 2015, vol. 141, pp. 221-24.10.1016/j.matlet.2014.11.087 ↗
37. 37. E. A. Brandes and G. B. Brook: Smithells Metals Reference Book, 7th ed., Butterworth-Heinemann, Oxford, 1992.
38. 38. N. M. Keita and S. Steinemann: J. Phys. C: Solid State Phys., 1978, vol. 11, pp. 4635-41.10.1088/0022-3719/11/23/010 ↗
39. 39. W. Cao, S. L. Chen, F. Zhang, K. Wu, Y. Yang, Y. A. Chang, R. Schmid-Fetzer and W. A. Oates: CALPHAD: Comput. Coupling Phase Diagrams Thermochem., 2009, vol. 33, pp. 328-42.10.1016/j.calphad.2008.08.004 ↗
40. L. Backerud, G. Chai and J. Tamminen: Solidification Characteristics of Aluminium Alloys, Vol. 2, Foundry Alloys, AFS/Skanaluminium, Des Plaines, 1990.
41. 41. A. G. C. Gwyer and H. W. L. Phillips: J. Inst. Met., 1927, vol. 38, pp. 29-83.
42. N. Krendelsberger, F. Weitzer and J. C. Schuster: Metall. Mater. Trans. A, 2007, vol. 38A, pp. 1681-91.10.1007/s11661-007-9182-x ↗
43. 43. D. Liang, Y. Bayraktar, S. A. Moir, M. Barkhudarov and H. Jones: Scripta Metall. Mater., 1994, vol. 31, pp. 363-67.10.1016/0956-716X(94)90001-9 ↗
44. 44. X. Cao, N. Saunders and J. Campbell: J. Mater. Sci., 2004, vol. 39, pp. 2303-14.10.1023/B:JMSC.0000019991.70334.5f ↗
45. 45. F. Wang, D. Eskin, J. W. Mi, T. Connolley, J. Lindsay and M. Mounib: Acta Mater., 2016, vol. 116, pp. 354-63.10.1016/j.actamat.2016.06.056 ↗
46. 46. H. W. Kerr, J. Cisse and G. F. Bolling: Acta Metall., 1974, vol. 22, pp. 677-86.10.1016/0001-6160(74)90077-7 ↗
47. 47. A. P. Titchener and J. A. Spittle: Met. Sci., 1974, vol. 8, pp. 112-16.10.1179/msc.1974.8.1.112 ↗
48. 48. D. H. StJohn and L. M. Hogan: Acta Metall., 1977, vol. 25, pp. 77-81.10.1016/0001-6160(77)90248-6 ↗
49. M. Hillert: Solidification and Casting of Metals, The Metals Society, London, 1979, pp 81–87.
50. 50. H. Fredriksson and T. Nylen: Met. Sci., 1982, vol. 16, pp. 283-94.10.1179/030634582790427370 ↗
51. 51. D. H. StJohn and L. M. Hogan: Acta Metall., 1987, vol. 35, pp. 171-74.10.1016/0001-6160(87)90226-4 ↗
52. 52. D. H. StJohn: Acta Metall. Mater., 1990, vol. 38, pp. 631-36.10.1016/0956-7151(90)90218-6 ↗
53. 53. G. Phragmen: J. Inst. Met., 1950, vol. 77, pp. 489-551.
54. 54. J. D. Hunt: J. Appl. Phys., 1966, vol. 37, pp. 254-57.10.1063/1.1707821 ↗