Effects of Friction Stir Processing Parameters and In Situ Passes on Microstructure and Tensile Properties of Al-Si-Mg Casting
Source abstract
Abstract
Friction stir processing (FSP) was applied to modify the microstructure of an as-cast A356 alloy. The effects of rotation rate, travel speed, in situ FSP pass, FSP direction, and artificial aging on microstructures and tensile properties were investigated. FSP broke up the coarse eutectic Si phase into 2.5 to 3.5 μm particles and distributed them homogeneously, and resulted in the dissolution of the coarse Mg2Si particles and the elimination of porosity, thereby improving both the strength and the ductility of the casting. Increasing the rotation rate was beneficial to breaking up and dissolving the particles, but it contributed little to eliminating the porosity. The travel speed did not affect the size of the particles apparently, but lower speed was beneficial to eliminating the porosity. 2-pass FSP showed an obvious advantage in the microstructure modification and tensile properties compared with the single-pass. However, a further increase of FSP passes only resulted in slight improvement. The FSP direction of the following pass did not show distinct effect on the microstructure and tensile properties. After post-FSP artificial aging, the strengthening phase (β″-Mg2Si) precipitated, which increased the strength and decreased the ductility of the FSP samples.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (33)
Show source-provided references
1. K.T. Kashyap, S. Murali, K.S. Raman, K.S.S. Murthy: Mater. Sci. Technol., 1994, vol. 9, pp. 189–203.10.1179/mst.1993.9.3.189 ↗
2. M.H. Lee, J.J. Kim, K.H. Kim, N.J. Kim, S. Lee, E.W. Lee: Mater. Sci. Eng. A, 2003, vol. 340, pp. 123–29.10.1016/S0921-5093(02)00157-0 ↗
3. D.L. Zhang, L. Zheng: Metall. Mater. Trans. A, 1996, vol. 27, pp. 3983–91.10.1007/BF02595647 ↗
4. Q.G. Wang, C.H. Caceres: Mater. Sci. Eng. A, 1998, vol. 241, pp. 72–82.10.1016/S0921-5093(97)00476-0 ↗
5. M.E. Seniw, J.G. Conley, M.E. Fine: Mater. Sci. Eng. A, 2000, vol. 285, pp. 43–48.10.1016/S0921-5093(00)00663-8 ↗
6. M.K. Surappa, E. Blank, J.C. Jaquet: Scripta Metall., 1986, vol. 20, pp. 1281–86.10.1016/0036-9748(86)90049-9 ↗
7. G. Atxaga, A. Pelayo, A.M. Irisarri: Mater. Sci. Technol., 2001, vol. 17, pp. 446–50.10.1179/026708301101510023 ↗
8. S. Kumai, J. Hu, Y. Higo, S. Nunomura: Acta Mater., 1996, vol. 44, pp. 2249–57.10.1016/1359-6454(95)00357-6 ↗
9. M.E. Seniw, J.G. Conley, M.E. Fine: NSF Symposium on Micromechanic Modeling of Industrial Materials. Elsevier Science SA, Seattle, WA, 1998, pp. 43–48.
10. W.W. Bose-Filho, E.R. de Freitas, V.F. da Silva, M.T. Milan, D. Spinelli: Int. J. Fatigue, 2007, vol. 29, pp. 1846–54.10.1016/j.ijfatigue.2007.01.006 ↗
11. H.R. Ammar, A.M. Samuel, F.H. Samuel: Mater. Sci. Eng. A, 2008, vol. 473, pp. 65–75.10.1016/j.msea.2007.03.112 ↗
12. F.M. Al-Kharafi, W.A. Badawy: Electrochim. Acta, 1995, vol. 40, pp. 1811–17.10.1016/0013-4686(95)00091-R ↗
13. J. Quaresma, C. Santos, A. Garcia: Metall. Mater. Trans. A, 2000, vol. 31, pp. 3167–78.10.1007/s11661-000-0096-0 ↗
14. P.R. Goulart, J.E. Spinelli, W.R. Osóio, A. Garcia: Mater. Sci. Eng. A, 2006, vol. 421, pp. 245–53.10.1016/j.msea.2006.01.050 ↗
15. K. Lee, Y.N. Kwon, S. Lee: J. Alloy. Compd., 2008, vol. 461, pp. 532–41.10.1016/j.jallcom.2007.07.038 ↗
16. L.B. Wang, S. Shivkumar: Z. Metallk., 1995, vol. 86, pp. pp. 441–45.
17. T.J. Hurley and R.G. Atkinson: Giessereipraxis, 1987, pp. 1–7.
18. W.M. Thomas, E.D. Nicholas, J.C. Needham, M.G. Murch, P. Templesmith, and C.J. Dawes: G.B. Patent Application No. 9125978.8, 1991.
19. W.B. Lee, Y.M. Yeon, S.B. Jung: Mater. Sci. Eng. A, 2003, vol. 355, pp. 154–59.10.1016/S0921-5093(03)00053-4 ↗
20. Z.Y. Ma, R.S. Mishra, M.W. Mahoney: Scripta Mater., 2004, vol. 50, pp. 931–35.10.1016/j.scriptamat.2004.01.012 ↗
21. S.R. Sharma, Z.Y. Ma, R.S. Mishra: Scripta Mater., 2004, vol. 51, pp. 237–41.10.1016/j.scriptamat.2004.04.014 ↗
22. Z.Y. Ma, S.R. Sharma, R.S. Mishra: Metall. Mater. Trans. A, 2006, vol. 37A, pp. 3323–36.10.1007/BF02586167 ↗
23. Z.Y. Ma, S.R. Sharma, R.S. Mishra: Mater. Sci. Eng. A, 2006, vol. 433, pp. 269–78.10.1016/j.msea.2006.06.099 ↗
24. Z.Y. Ma, A.L. Pilchak, M.C. Juhas, J.C. Williams: Scripta Mater., 2008, vol. 58, pp. 361–66.10.1016/j.scriptamat.2007.09.062 ↗
25. S. Jana, R.S. Mishra, J.B. Baumann, G. Grant: Scripta Mater., 2009, vol. 61, 992–95.10.1016/j.scriptamat.2009.08.011 ↗
26. L. Karthikeyan, V.S. Senthilkumar, K.A. Padmanabhan: Mater. Des., 2010, vol. 31, pp. 761–71.10.1016/j.matdes.2009.08.001 ↗
27. N. Sun, D. Apelian: JOM, 2011, vol. 63, pp. 44–50.10.1007/s11837-011-0190-3 ↗
28. S. Tutunchilar, M.K. Besharati Givi, M. Haghpanahi, P. Asadi: Mater. Sci. Eng. A, 2012, vol. 534, pp. 557–67.10.1016/j.msea.2011.12.008 ↗
29. S.A. Alidokht, A. Abdollah-zadeh, S. Soleymani, T. Saeid, H. Assadi: Mater. Charact., 2012, vol. 63, pp. 90–97.10.1016/j.matchar.2011.11.007 ↗
30. T.S. Mahmoud, O.M. Shaban, H.M. Zakaria, T.A. Khalifa: Mater. Sci. Technol., 2010, vol. 26, pp. 1120–24.10.1179/174328409X459310 ↗
31. M.W. Mahoney, C.G. Rhodes, J.G. Flintoff, R.A. Spurling, W.H. Bingel: Metall. Mater. Trans. A, 1998, vol. 29A, pp. 1955–64.10.1007/s11661-998-0021-5 ↗
32. Y.S. Sato, M. Urata, H. Kokawa, K. Ikeda: Mater. Sci. Eng. A, 2003, vol. 354, pp. 298–305.10.1016/S0921-5093(03)00008-X ↗
33. E. Ogris, A. Wahlen, H. Lühinger, P.J. Uggowitzer: J. Light Met., 2002, vol. 2, pp. 263–69.10.1016/S1471-5317(03)00010-5 ↗