Diffusion studies in the β (B2), β′ (bcc), and γ (fcc) Fe-Ni-Al alloys at 1000 °C
Source abstract
Abstract
Diffusion studies were carried out in the Fe-Ni-Al system at 1000 °C with solid-solid diffusion couples assembled with β (B2), β′ (bcc), and γ (fcc) single-phase alloys for the development of diffusion structures, diffusion paths, and for the determination of interdiffusion and intrinsic diffusion coefficients. The diffusion structures were examined by optical and scanning electron microscopy, and the concentration profiles were determined by electron microprobe analysis. Diffusion couples included several series of β vs γ and β′ vs γ diffusion couples characterized by a common terminal alloy bonded to several terminal alloys with varying compositions. The development of planar and nonplanar interfaces, as well as two-phase layers, as observed in various couples, were related to the diffusion paths. The interdiffusion fluxes of individual components were calculated directly from the experimental concentration profiles, and the diffusional interactions among components were examined in the light of zero-flux planes (ZFPs) and flux reversals, which were identified in several couples. Ternary interdiffusion coefficients ( $$\tilde Di,jFe $$ (i, j = Al, Ni)), with Fe considered as the dependent concentration variable, were evaluated at composition points of the intersection of diffusion paths of single-phase couples and of multiphase couples that developed planar interfaces. The interdiffusion coefficients were the largest in magnitude for the β′ alloys, especially near the β/β′ miscibility gap, and decreased for the β and γ alloys. In the β and γ phases, the main interdiffusion coefficient for Al was larger than those for Ni and Fe. Also, Fe interdiffused faster than Ni in the Fe-rich β and β′ phases. The cross-interdiffusion coefficients ( $$\tilde DAlNiFe $$ and $$\tilde DNiAlFe $$ ) were negative in all three phases. In general, the $$\tilde DAlNiFe $$ coefficients were larger in magnitude than the $$\tilde DNiAlFe $$ coefficients; however, the magnitude of $$\tilde DNiAlFe $$ was greater than that of $$\tilde DAlNiFe $$ near the β/(β + γ) phase boundary on the ternary isotherm. In the β phase, the magnitude of $$\tilde Di,jFe $$ (i, j=Al, Ni) coefficients increased over 1 to 2 orders of magnitude with a decrease in the Al concentration and increase in the Fe/Ni concentration ratio. Interdiffusion coefficients, extrapolated from the ternary coefficients for binary alloys, were consistent with those in literature. Intrinsic diffusion coefficients were also determined at selected compositions. In addition, tracer diffusion coefficients were estimated for the binary Fe-Al and Ni-Al alloys at selected compositions, from an extrapolation of ternary interdiffusion coefficients.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High Temperature Alloys and Creep · Intermetallics and Advanced Alloy Properties · Metallurgical and Alloy Processes
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (56)
Show source-provided references
1. J.S. Kirkaldy and D.J. Young: Diffusion in the Condensed State, Institute of Metals, London, 1987.
2. F.J.J. van Loo: Progr. Solid State Chem., 1990, vol. 20, pp. 47–99.10.1016/0079-6786(90)90007-3 ↗
3. M.A. Dayananda: Defect Diffusion Forum, 1992, vol. 83, pp. 73–86.10.4028/www.scientific.net/DDF.83.73 ↗
4. J.S. Kirkaldy: in Advances in Materials Research, H. Herman, ed., Interscience Publishers, New York, NY, 1970, vol. 4, pp. 55–100.
5. M.A. Dayananda: in Diffusion in Metals and Alloys, Londoldt and Bornstein, H. Mehrer, ed., Springer-Verlag, Berlin, 1991, Ser. III, vol. 26, pp. 372–436.
6. M.A. Dayananda: Metall. Mater. Trans. A, 1996, vol. 27A, pp. 2505–09.
7. M.A. Dayananda and Y.H. Sohn: Scripta Mater., 1996, vol. 35, pp. 683–88.10.1016/1359-6462(96)00145-5 ↗
8. M.A. Dayananda and Y.H. Sohn: Metall. Mater. Trans. A, 1999, vol. 30A, pp. 535–43.10.1007/s11661-999-0045-5 ↗
9. S.K. Kailasam and M.E. Glicksman: Acta Mater., 1999, vol. 47, pp. 905–13.10.1016/S1359-6454(98)00396-6 ↗
10. C.T. Liu and K.S. Kumar: J. Met., 1993, vol. 45, pp. 38–44.
11. E.P. George, M. Yamaguchi, K.S. Kumar, and C.T. Liu: Ann. Rev. Mater. Sci., 1994, vol. 24, pp. 409–51.10.1146/annurev.matsci.24.1.409 ↗
12. J.D. Cotton, R.D. Noebe, and M.J. Kaufman: in Structural Intermetallics, R. Darolia, J.J. Lewandoski, C.T. Liu, P.L. Martin, D.B. Miracle, and M.V. Nathal, eds., TMS, Warrendale, PA, 1993, pp. 513–22.
13. I. Baker, R.D. Noebe, and E.P. George: Interstitials and Substitutional Solute Effects in Intermetallics, TMS, Warrendale, PA, 1998.
14. A.J. Bradley: J. Iron Steel Inst., 1949, vol. 163, pp. 19–30; 1951, vol. 168, 1951, pp. 233–44; 1952, vol. 171, 41–47.
15. A.J. Bradley and A. Talyor: Proc. R. Soc. Series A, 1938, vol. 166, pp. 353–75.
16. G.H. Cheng and M.A. Dayananda: Metall. Trans. A, 1979, vol. 10A, pp. 1407–14.10.1007/BF02812004 ↗
17. W.B. Pearson: A Handbook of Lattice Spacing and Structure of Metals and Alloys, Pergamon Press, New York, 1967.
18. A. Steiner and K.L. Komarek: Trans. TMS-AIME, 1964, vol. 230, pp. 786–90.
19. K. Sato: Trans. JIM, 1963, vol. 3, pp. 121–24.
20. K. Hirano and A. Hishinuma: J. Jpn. Inst. Met., 1968, vol. 32, pp. 516–21.10.2320/jinstmet1952.32.6_516 ↗
21. K. Nishida, Y. Yamamoto, and T. Nagata: Trans. JIM, 1970, vol. 12, pp. 310–16.10.2320/matertrans1960.12.310 ↗
22. M. Weinhagan, B. Kohler, J. Wolff, and T. Hehenkamp: Defect Diffusion Forum, 1997, vols. 143–147, pp. 449–55.10.4028/www.scientific.net/DDF.143-147.449 ↗
23. Y.H. Sohn and M.A. Dayananda: Scripta Mater., 1999, vol. 40, pp. 79–84.10.1016/S1359-6462(98)00391-1 ↗
24. M.M.P. Janssen and G.D. Rieck: Trans. TMS-AIME, 1967, vol. 239, pp. 1372–84.
25. J.D. Whittenberger: Metall. Trans., 1972, vol. 3, pp. 2010–12.10.1007/BF02642597 ↗
26. M.M.P. Jannsen: Metall. Trans., 1973, vol. 4, pp. 1623–33.10.1007/BF02668017 ↗
27. S. Shankar and L.L. Siegle: Metall. Trans. A, 1978, vol. 9A, pp. 1467–76.10.1007/BF02661819 ↗
28. T.C. Chou and Y.T. Chou: Mater. Res. Soc. Symp. Proc., 1985, vol. 39, pp. 461–67.10.1557/PROC-39-461 ↗
29. M. Watanabe, Z. Horita, T. Sano, and M. Nemoto: Acta Metall. Mater., 1994, vol. 42, pp. 3381–88.10.1016/0956-7151(94)90470-7 ↗
30. M. Watanabe, Z. Horita, and M. Nemoto: Defect Diffusion Forum, 1997, vols. 143–147, pp. 637–42.10.4028/www.scientific.net/DDF.143-147.637 ↗
31. R. Kainuma, H. Ikenoya, I. Ohnuma, and K. Ishida: Defect Diffusion Forum, 1997, vols. 143–147, pp. 425–30.10.4028/www.scientific.net/DDF.143-147.425 ↗
32. J.I. Goldstein, R.E. Hanneman, and R.E. Ogilvie: Trans. TMS-AIME, 1965, vol. 233, pp. 812–20.
33. I.B. Borovsky, I.D. Marchukova, and Y.E. Ugaste: Phys. Met. Metallogr., 1967, vol. 24, pp. 51–56.
34. M.A. Krishtal, A.P. Mokrovand, and O.V. Stepanova: Phys. Met. Metallogr., 1967, vol. 24, pp. 101–05.
35. J. Levasseur and J. Philibert: C.R. Acad. Sci. Paris, 1967, vol. 264, pp. 380–83.
36. M. Badia and A. Vignes: C.R. Acad. Sci. Paris, 1964, vol. 264, pp. 1528–31.
37. T. Ustad and H. Sorum: Phys. Status Solid: (a), 1973, vol. 20, pp. 285–89.10.1002/pssa.2210200129 ↗
38. J. Poulinquen, S. Offret, and J. de Fouquet: C.R. Acad. Sci. Paris Ser. C, 1971, vol. 272, pp. 1952–55.
39. T.D. Moyer and M.A. Dayananda: Metall. Trans. A, 1976, vol. 7A, pp. 1035–40.10.1007/BF02644070 ↗
40. G.H. Cheng and M.A. Dayananda: Metall. Trans. A, 1979, vol. 10A, pp. 1415–19.10.1007/BF02812005 ↗
41. M.A. Dayananda and C.W. Kim: Metall. Trans. A, 1979, vol. 10A, pp. 1333–39.10.1007/BF02811989 ↗
42. M.A. Dayananda: Metall. Trans. A, 1983, vol. 14A, pp. 1851–58.10.1007/BF02645555 ↗
43. C.W. Kim and M.A. Dayananda: Metall. Trans. A, 1983, vol. 14A, pp. 857–64.10.1007/BF02644288 ↗
44. T.O. Ziebold and R.E. Ogilvie: Trans. TMS-AIME, 1967, vol. 239, pp. 942–53.
45. J.E. Morral, C. Jin, A. Engstrom, and J. Agren: Scripta Mater., 1996, vol. 34, pp. 1661–66.10.1016/1359-6462(96)00038-3 ↗
46. Y.H. Sohn and M.A. Dayananda: Acta Mater., 2000, vol. 48, pp. 1427–33.10.1016/S1359-6454(99)00454-1 ↗
47. Y.H. Sohn, M.A. Dayananda, G.L. Hofman, R.V. Stain, and S.L. Hayes: J. Nucl. Mater., 2000, vol. 279, pp. 317–29.10.1016/S0022-3115(99)00290-1 ↗
48. L. Onsager: Phys. Rev., 1931, vol. 37, pp. 405–26; 1932, vol. 38, pp. 2265–79.10.1103/PhysRev.37.405 ↗
49. L. Onsager: Ann. NY Acad. Sci., 1965, vol. 46, pp. 241–65.10.1111/j.1749-6632.1945.tb36170.x ↗
50. T. Heumann: Z. Phys. Chem., 1952, vol. 201, pp. 168–89.10.1515/zpch-1952-20114 ↗
51. A.G. Guy and J. Philibert: Z. Metallkd., 1965, vol. 50, pp. 841–45.
52. M.A. Dayananda: Trans. TMS-AIME, 1968, vol. 242, pp. 1369–72.
53. A.G. Guy and C.B. Smith: Trans. ASM, 1962, vol. 55, pp 1–9.
54. Y.H. Sohn: Ph.D. Dissertation, Purdue University, West Lafayette, IN, 1998.
55. R. Kikuchi and H. Sato: J. Chem. Phys., 1969, vol. 51, pp. 161–81.10.1063/1.1671704 ↗
56. R.D. Sisson, Jr. and M.A. Dayananda: Metall. Trans., 1972, vol. 3, pp. 647–52.10.1007/BF02642746 ↗