Dry sliding wear behavior of plasma-sprayed aluminum hybrid composite coatings
Source abstract
Abstract
Al-SiCp composite and Al-SiCp-Cp hybrid composite coatings were produced by plasma spraying of premixed powders onto A356 alloy substrates. Four composite coatings, Al+20 vol pct SiCp, Al+20 vol pct SiCp+Cp, Al+40 vol pct SiCp, and Al+40 vol pct SiCp+Cp, were obtained. The dry sliding wear behavior of these coatings and pure aluminum have been studied at a sliding velocity of 1 m/s in the applied-load range of 25 to 150 N (corresponding to a normal stress of 0.5 to 3 MPa). The composite coatings had a significantly improved wear resistance over pure Al. The composite coatings with a higher SiCp content of 40 vol pct exhibited superior wear resistance than those with a lower SiCp content of 20 vol pct. The presence of graphite particles had different influences on the wear resistance, depending on the applied load. At lower loads, graphite improved the wear resistance considerably. At higher loads, the wear resistance of the hybrid composite coatings was similar to that of the composite coatings without graphite particles. At lower loads, an oxidative wear mechanism was dominant. At higher loads, delamination was a major wear mechanism. Graphite particles did not change their wear mechanism at the same applied loads.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Tribology and Wear Analysis · Advanced materials and composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (24)
Show source-provided references
1. Y.W. Chan: J. Mater. Proc. Technol., 1992, vol. 29, pp. 223–34.10.1016/0924-0136(92)90437-W ↗
2. D.O. Kennedy: Adv. Mater. Proc., 1991, vol. 6, pp. 42–46.
3. C.G.E. Mangin, J.A. Isaacs, and J.P. Clark: JOM, 1996, vol. 48, pp. 49–51.10.1007/BF03221383 ↗
4. K. Ghosh, T. Troczynski, and A.C.D. Chaklader: J. Thermal Spray Technol., 1998, vol. 7 (1), pp. 78–86.10.1361/105996398770351070 ↗
5. K.A. Khor, F.Y.C. Boey, Y. Murakoshi, and T. Sano: J. Thermal Spray Technol., 1994, vol. 3, pp. 162–68.10.1007/BF02648273 ↗
6. R.L. Deuis, J.M. Yellup, and C. Subramanian: Composites Sci. Technol., 1998, vol. 58, pp. 299–309.10.1016/S0266-3538(97)00131-0 ↗
7. G. Sundararajan, K.U.M. Prasad, D.S. Rao, and S.V. Joshi: J. Mater. Eng. Performance, 1998, vol. 7, pp. 343–51.10.1361/105994998770347783 ↗
8. R.L. Deuis and C. Subramanian: Mater. Sci. Technol., 2000, vol. 16, pp. 209–19.10.1179/026708300101507569 ↗
9. B. Wielage, S. Steinhauser, T. Schnick, and D. Nickelmann: J. Thermal Spray Technol., 1999, vol. 8, pp. 553–58.10.1361/105996399770350241 ↗
10. K. Nakata and M. Ushiroda: Surf. Eng., 1997, vol. 13, pp. 45–49.10.1179/sur.1997.13.1.45 ↗
11. G. Barbezat and G. Wuest: Surf. Eng., 1998, vol. 14, pp. 113–16.10.1179/sur.1998.14.2.113 ↗
12. T.F. Stephenson, A.E.M. Warner, S. Wilson, A.T. Alpas, and P.K. Rohatgi: in Processing, Properties and Applications of Cast Metal Matrix Composites, P. Rohatgi and P.A. Khan, eds., TMS, Warrendale, PA, 1996, pp. 337–51.
13. S.X. Huang and K. Paxton: JOM, 1998, vol. 50 (8), pp. 26–28.10.1007/s11837-998-0453-9 ↗
14. B. Venkataraman and G. Sundararajan: Acta Mater., 1996, vol. 44, pp. 461–73.10.1016/1359-6454(95)00218-9 ↗
15. A.T. Alpas and J. Zhang: Wear, 1992, vol. 155, pp. 83–104.10.1016/0043-1648(92)90111-K ↗
16. A.T. Alpas and J. Zhang: Metall. Mater. Trans., A1994, vol. 25A, pp. 969–83.10.1007/BF02652272 ↗
17. R.A. Saravanan, J.M. Lee, and S.B. Kang: Metall. Mater. Trans., A1999, vol. 30A, pp. 2523–37.10.1007/s11661-999-0261-z ↗
18. A. Wang and H.J. Rack: Mater. Sci. Eng., 1991, vol. 147A, pp. 211–24.10.1016/0921-5093(91)90848-H ↗
19. J. Zhang and A.T. Alpas: Acta Mater., 1997, vol. 45, pp. 513–28.10.1016/S1359-6454(96)00191-7 ↗
20. K. Razavizadeh and T.S. Eyre: Wear, 1982, vol. 79, pp. 325–33.10.1016/0043-1648(82)90322-2 ↗
21. Z.F. Zhang, L.C. Zhang, and Y.W. Mai: J. Mater. Sci., 1995, vol. 30, pp. 1961–66.10.1007/BF00353018 ↗
22. K.C. Ludema: Wear, 1984, vol. 100, pp. 315–31.10.1016/0043-1648(84)90019-X ↗
23. R.L. Deuis, J.M. Yellup, and C. Subramanian: Composites Sci. Technol., 1997, vol. 57, pp. 415–35.10.1016/S0266-3538(96)00167-4 ↗
24. M. Noguchi and K. Fukizawa: Adv. Mater. Proc., 1993, vol. 143, (6), p. 21.