Precipitates in As-Cast and Heat-Treated ASTM F75 Co-Cr-Mo-C Alloys Containing Si and/or Mn
Source abstract
Abstract
The effect of the addition of Si or Mn to ASTM F75 Co-28Cr-6Mo-0.25C alloys on precipitate formation as well as dissolution during solution treatment was investigated. Three alloys—Co-28Cr-6Mo-0.25C-1Si (1Si), Co-28Cr-6Mo-0.25C-1Mn (1Mn), and Co-28Cr-6Mo-0.25C-1Si-1Mn (1Si1Mn)—were heat treated from 1448 K to 1548 K (1175 °C to 1275 °C) for a holding time of up to 43.2 ks. In the case of the as-cast 1Si and 1Si1Mn alloys, the precipitates were M23C6-type carbide, η phase (M6C-M12C–type carbide), and π phase (M2T3X-type carbide with a β-Mn structure), while in the case of the as-cast 1Mn alloy, M23C6-type carbide and η phase were detected. The 1Si and 1Si1Mn alloys required longer heat-treatment times for complete precipitate dissolution than did the 1Mn alloys. During the solution treatment, blocky dense M23C6-type carbide was observed in all the alloys over the temperature range of 1448 K to 1498 K (1175 °C to 1225 °C). At the heat-treatment temperature of 1523 K (1250 °C), starlike precipitates with stripe patterns—comprising M23C6-type carbide and metallic face-centered-cubic (fcc) γ phase—were detected in the 1Si and 1Si1Mn alloys. A π phase was observed in the 1Si and 1Si1Mn alloys heat treated at 1523 K and 1548 K (1250 °C and 1275 °C) and in the 1Mn alloy heat treated at 1548 K (1275 °C); its morphology was starlike-dense. The addition of Si appeared to promote the formation of the π phase in Co-28Cr-6Mo-0.25C alloys at 1523 K and 1548 K (1250 °C and 1275 °C). Thus, the addition of Si and Mn affects the phase and morphology of the carbide precipitates in biomedical Co-Cr-Mo alloys.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced materials and composites · Metal Alloys Wear and Properties · Microstructure and Mechanical Properties of Steels
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (27)
Show source-provided references
1. ASTM F75–07, Annual Book of ASTM Standards, ASTM International, West Conshohocken, PA, 2008, vol. 13.01, pp. 64–66
2. L.E. Ramírez, M. Castro, M. Méndez, J. Lacaze, M. Herrera, and G. Lesoult: Scripta Mater., 2002, vol. 47, pp. 811–16.10.1016/S1359-6462(02)00305-6 ↗
3. M. Niinomi, T. Hanawa, and T. Narushima: JOM, 2005, vol. 57 (4), pp. 18–24.10.1007/s11837-005-0076-3 ↗
4. S.H. Lee, N. Nomura, and A. Chiba: Mater. Trans., 2008, vol. 49, pp. 260–64.10.2320/matertrans.MRA2007220 ↗
5. M. Niinomi: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 477–86.10.1007/s11661-002-0109-2 ↗
6. J.W. Weeton and R.A. Signorelli: Trans. Am. Soc. Met., 1955, vol. 47, pp. 815–45.
7. K. Asgar and F.A. Peyton: J. Dent. Res., 1961, vol. 40, pp. 73–86.10.1177/00220345610400012601 ↗
8. A.J.T. Clemow and B.L. Daniell: J. Biomed. Mater. Res., 1979, vol. 13, pp. 265–79.10.1002/jbm.820130208 ↗
9. T. Kilner, R.M. Pilliar, G.C. Weatherly, and C. Allibert: J. Biomed. Mater. Res., 1982, vol. 16, pp. 63–79.10.1002/jbm.820160109 ↗
10. S. Mineta, S. Namba, T. Yoneda, K. Ueda, and T. Narushima: Metall. Mater. Trans. A, 2010, vol. 41A, pp. 2129–38.10.1007/s11661-010-0227-1 ↗
11. D.S. Janisch, M. Garel, A. Eder, W. Lengauer, K. Dreyer, and H. van den Berg: Int. J. Refract. Met. Hard Mater., 2008, vol. 26, pp. 179–89.10.1016/j.ijrmhm.2007.05.006 ↗
12. A.C. Fraker and H.H. Stadelmaier: Trans. TMS-AIME, 1969, vol. 245, pp. 847–50.
13. J.M. Guilemany, J.M. de Paco, J. Nutting, and J.R. Miguel: Metall. Mater. Trans. A, 1999, vol. 30A, pp. 1913–21.10.1007/s11661-999-0002-3 ↗
14. J. Jeciejewicz: J. Less-Common Met., 1964, vol. 7, pp. 318–20.10.1016/0022-5088(64)90028-1 ↗
15. H.S. Dobbs and J.L.M. Robertson: J. Mater. Sci., 1983, vol. 18, pp. 391–401.10.1007/BF00560627 ↗
16. M. Caudillo, M. Herrera-Trejo, M.R. Castro, E. Ramírez, C.R. González, and J.I. Juárez: J. Biomed. Mater. Res., 2002, vol. 59, pp. 378–85.10.1002/jbm.10001 ↗
17. M. Herrera, A. Espinoza, J. Méndez, M. Castro, J. López, and J. Rendón: J. Mater. Sci.: Mater. Med., 2005, vol. 16, pp. 607–11.10.1007/s10856-005-2530-8 ↗
18. H. Mancha, E. Carranza, J.I. Escalante, G. Mendoza, M. Méndez, F. Cepeda, and E. Valdés: Metall. Mater. Trans. A, 2001, vol. 32A, pp. 979–84.10.1007/s11661-001-0355-8 ↗
19. Montero-Ocampo, M. Talavera, and H. Lopez: Metall. Mater. Trans. A, 1999, vol. 30A, pp. 611–2010.1007/s11661-999-0052-6 ↗
20. R.N.J. Taylor and R.B. Waterhouse: J. Mater. Sci., 1983, vol. 18, pp. 3265–80.10.1007/BF00544151 ↗
21. S.H. Lee, N. Nomura, and A. Chiba: Mater. Trans., 2007, vol. 48, pp. 2207–11.10.2320/matertrans.MRA2007004 ↗
22. Z. de la Garza, M. Herrera-Trejo, M. Castro R., E. Ramírez V., M. Mendez N., and J. Mendez N.: J. Mater. Eng. Perform., 2001, vol. 10, pp. 153–5610.1361/105994901770345150 ↗
23. JCPDS card no. 26-0428
24. M. Kikuchi, S. Wakita, and R. Tanaka: Trans. ISIJ, 1973, vol. 13, pp. 226–28.10.2355/isijinternational1966.13.226 ↗
25. S. Wakita, M. Kikuchi, and R. Tanaka: Tetsu-to-Hagané, 1975, vol. 61, pp. 2418–32.10.2355/tetsutohagane1955.61.10_2418 ↗
26. M. Kikuchi, T. Sekita, S. Wakita, and R. Tanaka: Tetsu-to-Hagané, 1981, vol. 67, pp. 1981–89.10.2355/tetsutohagane1955.67.11_1981 ↗
27. B.C. De Cooman: Curr. Opin. Solid State Mater. Sci., 2004, vol. 8, pp. 285–303.10.1016/j.cossms.2004.10.002 ↗