journal article·2016-07

Induction Tempering vs Conventional Tempering of a Heat-Treatable Steel

Stephanie Sackl, Michael Zuber, Helmut Clemens, Sophie Primig

Publisher page

Abstract

An induction heat treatment is favorable compared to a conventional one mainly due to significant time and cost savings. Therefore, in this study, the microstructure property relationships during induction and conventional heat treatment of a heat treatable steel 42CrMo4 is investigated. The yield strength and hardness is slightly higher for the conventionally heat-treated steel, whereas the induction heat-treated condition exhibits a roughly 30 J/cm2 higher impact energy. In a previous investigation of the authors, it has been proved that the difference in yield strength originates from the smaller block size of the conventionally heat-treated steel, which was already present after hardening. In the present work, it can be shown that during tempering the martensitic blocks become equi-axed ferrite grains due to recrystallization as revealed by electron back scatter diffraction. Nevertheless, a larger grain size usually is less favorable for the impact toughness of steels. Therefore, another mechanism is responsible for the higher impact energy of the induction hardened and tempered steel. With the aid of transmission electron microscopy a finer distribution of cementite was observed in the induction heat-treated samples. The delay of recovery is the reason for the presence of finer cementite in case of the induction heat-treated steel. Here, the higher heating rates and shorter process times reduce the annihilation of dislocation and as a consequence provide more nucleation sites for precipitation of cementite during tempering. From the obtained experimental results, it is believed that the finer distribution of carbides causes the observed higher impact toughness.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Metallurgy and Material Forming

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (27)

Show source-provided references
1. 1. S. T. Ahn, D. S. Kim, and W. J. Nam, J. Mater. Process. Technol. 160, 54 (2005).10.1016/j.jmatprotec.2004.03.019 ↗
2. 2. C. Revilla, B. López, and J. M. Rodriguez-Ibabe, Mater. Des. 62, 296 (2014).10.1016/j.matdes.2014.05.053 ↗
3. J. M. Mendizabal, L., Rodriguez-Ibabe, Mater. Sci. Technol. (2005), pp. 77–84.
4. C. Revilla, P. Uranga, B. López, and J.M. Rodriguez-Ibabe, in AIST Steel Prop. Appl. Conf. Proc.—Comb. with MS T’12, Mater. Sci. Technol. 2012 (2012), pp. 267–74.
5. 5. H. Leitner, D. Caliskanoglu, and H. Clemens, BHM Berg- und Hüttenmännische Monatshefte 149, 172 (2004).
6. 6. S. Sackl, H. Leitner, M. Zuber, H. Clemens, and S. Primig, Metall. Mater. Trans. A 45, 5657 (2014).10.1007/s11661-014-2518-4 ↗
7. K. C. Smith, J. P. Wise, and G. Krauss, Prog. Heat Treat. Surf. Eng. (2000), pp. 379–86.
8. 8. J. Grosch, B. Kocjancic, and G. Reichelt, Haerterei Technsiche Mitteilungen 39, 199 (1984).
9. Krauss, G. (2012). Phase Transform Steels (pp. 126–150). Elsevier, Amsterdam10.1533/9780857096111.1.126 ↗
10. 10. G. Speich and W. Leslie, Metall. Trans. A 3, 1043 (1972).10.1007/BF02642436 ↗
11. 11. R. C. Thomson and M. K. Miller, Appl. Surf. Sci. 94-95, 313 (1996).10.1016/0169-4332(95)00392-4 ↗
12. M.K. Miller, P.A. Beaven, and G.D.W. Smith, Metall. Trans. A 12, 1197 (1981).10.1007/BF02642333 ↗
13. E. R. Parker, Metall. Trans. A, 8, 1025–1042 (1977).10.1007/BF02667387 ↗
14. 14. H. Bhadeshia and R. Honeycombe, Steels Microstructure and Properties, 3rd ed. (Butterworth-Heinemann (Elsevier), Oxford, 2006).
15. 15. K. Hanawa and T. Mimura, Metall. Trans. A 15A, 1147 (1984).10.1007/BF02644709 ↗
16. 16. D. Dengel, Haerterei Technsiche Mitteilungen 39, 182 (1984).
17. 17. S. Primig and H. Leitner, Thermochim. Acta 526, 111 (2011).10.1016/j.tca.2011.09.001 ↗
18. 18. T. Furuhara, K. Kobayashi, and T. Maki, ISIJ Int. 44, 1937 (2004).10.2355/isijinternational.44.1937 ↗
19. 19. R. N. Caron and G. Krauss, Metall. Trans. 3, 2381 (1972).10.1007/BF02647041 ↗
20. 20. M. Hayakawa, S. Matsuoka, K. Tsuzaki, H. Hanada, and M. Sugisaki, Scr. Mater. 47, 655 (2002).10.1016/S1359-6462(02)00263-4 ↗
21. 21. S. Xing, Z. Chen, Y. Ma, and H. Li, J. Iron Steel Res. Int. 19, 43 (2012).10.1016/S1006-706X(12)60058-2 ↗
22. 22. J. Wu, P. J. Wray, C. I. Garcia, M. Hua, and A. J. Deardo, ISIJ Int. 45, 254 (2005).10.2355/isijinternational.45.254 ↗
23. 23. F. Foroozmehr, A. Najafizadeh, and A. Shafyei, Mater. Sci. Eng. A 528, 5754 (2011).10.1016/j.msea.2011.04.055 ↗
24. 24. L. S. Darken, Trans. AIME 175, 184 (1948).
25. 25. A. A. Zhukov, Met. Sci. Heat Treat. 18, 1070 (1976).10.1007/BF00705181 ↗
26. 26. J. Verhoeven, J. Mater. Eng. Perform. 9, 286 (2000).10.1361/105994900770345935 ↗
27. G. Krauss, Metall. Mater. Trans. B 34, 781 (2003).10.1007/s11663-003-0084-z ↗