journal article·2009-01

Interface Effects on the Fracture Mechanism of a High-Toughness Aluminum-Composite Laminate

C.M. Cepeda-Jiménez, M. Pozuelo, J.M. García-Infanta, O.A. Ruano, F. Carreño

Publisher page

Abstract

The microstructure and the mechanical properties of a multilayer composite laminate based on aluminum 7075 and 2024 alloys produced by hot roll-bonding were examined. The composite laminate has been tested at room temperature under impact Charpy tests, three-point bend tests and shear tests on the interfaces. The toughness of the post-rolling tempered and T6 treated composite laminate, measured by impact absorbed energy in the crack arrester orientation, was more than twenty times higher than that of the monolithic Al 7075 alloy and seven times higher than that of Al 2024 alloy. The outstanding toughness increase of the composite laminate in the post-rolling tempered and T6 treated condition is mainly due to the mechanism of “interface predelamination”. By this fracture mechanism the interfaces are debonded before the main crack reaches them, warranting delamination in all interfaces. Therefore, delamination and crack renucleation in every layer are responsible for the improvement in toughness.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Advanced Welding Techniques Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (31)

Show source-provided references
1. J.C. Williams, E.A. Starke Jr.: Acta Mater., 2003, vol. 51, pp. 5775–9910.1016/j.actamat.2003.08.023 ↗
2. J.A. Nock: in Aluminum, Properties and Physical Metallurgy, J.E. Hatch, ed., ASM, Metals Park, OH, 1984, pp. 351–78
3. E.A. Starke Jr., J.T. Staley: Prog. Aerospace Sci., 1996, vol. 32 pp. 131–7210.1016/0376-0421(95)00004-6 ↗
4. T. Warner: Mater. Sci. Forum, 2006, vols. 519–521, pp. 1271–7810.4028/www.scientific.net/MSF.519-521.1271 ↗
5. H.T. Lee, G.H. Shaue: Mater. Sci. Eng. A, 1999, vol. 268, pp. 154–6410.1016/S0921-5093(99)00069-6 ↗
6. S. Ozden, R. Ekici, F. Nair: Compos. Part A, 2007, vol. 38, pp. 484–9410.1016/j.compositesa.2006.02.026 ↗
7. J. Wadsworth, D.R. Lesuer: Mater. Charact., 2000, vol. 45, pp. 289–31310.1016/S1044-5803(00)00077-2 ↗
8. T.M. Osman, J.J. Lewandowski, D.R. Lesuer: Mater. Sci. Eng. A, 1997, vol. 229, pp. 1–910.1016/S0921-5093(97)00001-4 ↗
9. R. Alderliesten, G. Campoli, R. Benedictus: Compos. Sci. Technol., 2007, vol. 67, pp. 2545–5510.1016/j.compscitech.2006.12.011 ↗
10. G. Caprino, V. Lopresto, P. Iaccarino: Compos. Part. A, 2007, vol. 38, pp. 290–30010.1016/j.compositesa.2006.04.005 ↗
11. T.M. Osman, P.M. Singh, J.J. Lewandowski: Scripta Metall. Mater., 1994, vol. 31, pp. 607–1210.1016/0956-716X(94)90152-X ↗
12. H.A. Hassan, J.J. Lewandowski, M.H. Abd El-Latif: Metall. Mater. Trans. A, 2004, vol. 35A, pp. 2291–230310.1007/s11661-006-0209-5 ↗
13. L.Y. Ellis, J.J. Lewandowski: Mater. Sci. Eng. A, 1994, vol. 183, pp. 59–6710.1016/0921-5093(94)90890-7 ↗
14. H.A. Hassan, J.J. Lewandowski, M.H. Abd El-Latif: Metall. Mater.Trans. A, 2004, vol. 35A, pp. 45–5210.1007/s11661-004-0107-7 ↗
15. M. Pozuelo, F. Carreño, C.M. Cepeda-Jimenez, O.A. Ruano: Metall. Mater. Trans. A, 2008, vol. 39A, pp. 666–71.10.1007/s11661-007-9441-x ↗
16. M. Pozuelo, F. Carreño, O.A. Ruano: Mater. Sci. Forum, 2003, vol. 426, pp. 883–8810.4028/www.scientific.net/MSF.426-432.883 ↗
17. D.R. Lesuer, C.K. Syn, O.D. Sherby, J. Wadsworth, J.J. Lewandowski, W.H. Hunt Jr.: Int. Mater. Rev., 1996, vol. 41 (5), pp. 169–9710.1179/imr.1996.41.5.169 ↗
18. D.W. Kum, T. Oyama, O.A. Ruano, O.D. Sherby: Metall. Trans. A, 1986, vol. 17A, pp. 1517–2110.1007/BF02650087 ↗
19. M. Pozuelo, F. Carreño, O.A. Ruano: Compos. Sci. Technol., 2006, vol. 66, pp. 2671–7610.1016/j.compscitech.2006.03.018 ↗
20. D.W. Kum, T. Oyama, J. Wadsworth, O.D. Sherby: J. Mech. Phys., 1983, vol. 31, pp. 173–8610.1016/0022-5096(83)90049-2 ↗
21. H. Kaçar, E. Atik, C. Meriç: J. Mater. Process. Technol., 2003, vol. 142, pp. 762–6610.1016/S0924-0136(03)00642-3 ↗
22. N. Kamikawa, N. Tsuji, X. Huang, N. Hansen: Acta Mater., 2006, vol. 54, pp. 3055–6610.1016/j.actamat.2006.02.046 ↗
23. G.E. Dieter: Mechanical Metallurgy, McGraw-Hill, London, United Kingdom, 1988, pp. 12–15
24. F. Viana, A.M.P. Pinto, H.M.C. Santos, A.B. Lopes: J. Mater. Process. Technol., 1999, vols. 92–93, pp. 54–5910.1016/S0924-0136(99)00219-8 ↗
25. C. Genevois, A. Deschamps, A. Denquin, B. Doisneau-Cottignies: Acta Mater., 2005, vol. 53, pp. 2447–5810.1016/j.actamat.2005.02.007 ↗
26. C. Badini, F. Marino, E. Verné: Mater. Sci. Eng. A, 1995, vol. 191, pp. 185–9110.1016/0921-5093(94)09637-C ↗
27. L.F. Mondolfo: Aluminium Alloys: Structure and Properties, Butterworth and Co., Boston, MA, 1976, pp. 695–99
28. Y.H. Zhao, X.Z. Liao, Z. Jin, R.Z. Valiev, Y.T. Zhu: Acta Mater., 2004, vol. 52, pp. 4589–9910.1016/j.actamat.2004.06.017 ↗
29. D.R. Bloyer, K.T. Venkateswara Rao, R.O. Ritchie: Mater. Sci. Eng. A, 1996, vol. 216, pp. 80–9010.1016/0921-5093(96)10391-9 ↗
30. D.R. Bloyer, K.T. Venkateswara Rao, R.O. Ritchie: Metall. Mater. Trans. A, 1998, vol. 29A, pp. 2483–9610.1007/s11661-998-0220-0 ↗
31. T.M. Osman, H.A. Hassan, J.J. Lewandowski: Metall. Mater. Trans. A, 2008, vol. 39A, pp. 1993–220610.1007/s11661-008-9538-x ↗