Effect of normalization temperature on the creep strength of modified 9Cr-1Mo steel
Source abstract
Abstract
The effect of normalization temperature from 850 °C to 1050 °C on the structure and creep-rupture properties of modified 9Cr-1Mo steel was studied. Normalization at temperatures below 925 °C resulted in structures containing significant polygonized, recovered ferrite. The ferrite structures had poor creep-rupture strength: roughly two orders of magnitude increase in minimum creep rate or decrease in rupture life for 850 °C compared to 1050 °C normalization at test conditions of 600 °C and 145 MPa. Room-temperature strength and hardness were also reduced. The microstructure after normalization at the standard 1050 °C temperature consisted of tempered martensite with fine M23C6 carbide along prior austenite and lath boundaries and fine MX carbonitride precipitates within the laths. Normalization at temperatures between 925 °C and 1000 °C also resulted in reduced creep strength in comparison with 1050 °C normalization, even though tempered martensite microstructures were formed and little change in room-temperature strength was observed; the reduction was attributed to subtle differences in the MX precipitates. The effect of reduced normalization temperature was more pronounced for higher-temperature, lower-stress creep-rupture conditions.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High Temperature Alloys and Creep · Metal Alloys Wear and Properties · Intermetallics and Advanced Alloy Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (32)
Show source-provided references
1. A. Fleming, R.V. Maskell, L.W. Buchanan, and T. Wilson: in Materials for High Temperature Power Generation and Process Plant Applications, A. Strang, ed., IOM Communications, London, 2000, pp. 33–77.
2. F.B. Pickering: in Microstructural Development and Stability in High Chromium Ferritic Power Plant Steels, A. Strang and D.J. Gooch, eds., Institute of Materials, London, 1997, pp. 1–29.
3. P.J. Ennis and A. Czyrska-Filemonowicz: OMMI, 2002, vol. 1. Available at www.ommi.co.uk
4. K. Maruyama, K. Sawada, and J. Koike: ISIJ Int., 2001, vol. 41, pp. 641–53.10.2355/isijinternational.41.641 ↗
5. J. Orr and L. Woollard: in Microstructural Development and Stability in High Chromium Ferritic Power Plant Steels, A. Strang and D.J. Gooch, eds., Institute of Materials, London, 1997.
6. R. Viswanathan and W. Bakker: Materials for Boilers in Ultra Super-critical Power Plants in 2000 International Joint Power Generation Conference IJPG2000, 2000. Miami Beach, FL: ASME.
7. F. Masuyama: ISIJ Int., 2001, vol. 41, pp. 612–25.10.2355/isijinternational.41.612 ↗
8. T.A. Allen, S. Bruemmer, J. Elmer, M. Kassner, A. Motta, G.R. Odette, R.E. Stoller, G. Was, W. Wolfer, and S. Zinkle: Higher Temperature Reactor Materials Workshop, Argonne National Laboratory Report ANL-02/12, 2002.
9. “Next Generation Nuclear Plant Materials Research and Development Program Plan,” Idaho National Engineering and Environmental Laboratory Report INEEL/EXT-04-02347, 2004.
10. R.L. Klueh and D.R. Harries: High-Chromium Ferritic and Martensitic Steels for Nuclear Applications, ASTM, West Conshohocken, PA, 2001.10.1520/MONO3-EB ↗
11. W.B. Jones, C.R. Hills, and D.H. Polonis: Metall. Trans. A, 1991, vol. 22A, pp. 1049–58.10.1007/BF02661098 ↗
12. V.K. Sikka, M.G. Cowgill, and B.W. Roberts, in Ferritic Alloys for Use in Nuclear Energy Technologies, J.W. Davis and D.J. Michel, eds., TMS, Warrendale, PA, 1983, pp. 413–23.
13. H. Okamura, R. Ohtani, K. Saito, K. Kimura, R. Ishii, K. Fujiyama, S. Hongo, T. Iseki, and H. Uchida: Nucl. Eng. Des., 1999, vol. 193, pp. 243–54.10.1016/S0029-5493(99)00181-8 ↗
14. S. Spigarelli, E. Cerri, P. Bianchi, and E. Evangelista: Mater. Sci. Technol., 1999, vol. 15, pp. 1433–40.10.1179/026708399101505428 ↗
15. J.M. Vitek and R.L. Klueh: Metall. Trans. A, 1983, vol. 14A, pp. 1047–55.10.1007/BF02659853 ↗
16. R.D. Townsend: in Materials for High Temperature Power Generation and Process Plant Applications, A. Strang, ed., IOM Communications, London, U.K., 2000, pp. 199–223.
17. D.R. Barraclough and D.J. Gooch: Mater. Sci. Technol., 1985, vol. 1, pp. 961–67.10.1179/mst.1985.1.11.961 ↗
18. J. Hald: in Microstructural Stability of Creep Resistant Alloys for High Temperature Plant Applications, A. Strang, J. Cawley, and G.W. Greenwood, eds., IOM Communications Ltd., London, U.K., 1998, pp. 173–84.
19. M.J. Cohn, J.F. Henry, and D. Nass: ASME, 2005, vol. 127, pp. 197–203.
20. V.K. Sikka, C.T. Ward, and K.C. Thomas: in Ferritic Steels for High-Temperature Applications, A.K. Khare, ed., ASM, Metals Park, OH, 1983, pp. 65–84.
21. G.C. Bodine and R.E. McDonald: in Ferritic Steels for High-Temperature Applications, A.K. Khare, ed., ASM, Metals Park, OH, 1983, pp. 9–20.
22. C. Garcia de Andres, F.G. Caballero, C. Capdevila, and L.F. Alvarez: Mater. Charact., 2002, vol. 48, pp. 101–11.10.1016/S1044-5803(02)00259-0 ↗
23. S. Spigarelli, E. Cerri, E. Evangelista, and P. Bontempi: in Advanced Heat Resistant Steel for Power Generation, R. Viswanathan and J. Nutting, eds., IOM Communications, London, U.K., 1999, pp. 247–58.
24. F.C. Monkman and N.J. Grant: Proc. ASTM, 1956, vol. 56, pp. 593–620.
25. H. Cerjak, V. Foldyna, P. Hofer, and B. Schaffernak: in Microstructural Development and Stability in High Chromium Ferritic Power Plant Steels, A. Strang and D.J. Gooch, eds., Institute of Materials, London, U.K., 1997, pp. 145–58.
26. P. Bianchi, P. Bontempi, A. Benvenuti, and N. Ricci: in Microstructural Stability of Creep Resistant Alloys for High Temperature Plant Applications, A. Strang, J. Cawley, and G.W. Greenwood, eds., IOM Communications, London, U.K., 1998, pp. 107–16.
27. A. Orlova, J. Bursik, K. Kucharova, and V. Sklenicka: in Microstructural Stability of Creep Resistant Alloys for High Temperature Plant Applications, A. Strang, J. Cawley, and G.W. Greenwood, eds., IOM Communications, London, U.K., 1998, pp. 89–106.
28. K. Kimura: Proceedings of the 2005 ASME Pressure Vessels and Piping Division Conference, Denver Co, July 17–21, 2005, ASME International, New York, NY.
29. J.-T. Kim, Y.-S. Lee, B.-O. Kong, and S.-H. Ryu: Proceedings of the 2005 ASME Pressure Vessels and Piping Division Conference, Denver, CO, July 17–21, 2005, ASME International, New York, NY.
30. ASME Boiler and Pressure Vessel Code, ASME International, New York, NY, 2004, p. 96.
31. D. Burton, J. Orr, and J.B. Marriott: in Ferritic Steels for Fast Reactor Steam Generators, S.F. Pugh and E.A. Little, eds., British Nuclear Energy Society, London, U.K., 1978, pp. 205–11.
32. SA-182: Specification for Forged or Rolled Alloy-Steel Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service, ASME International, New York, NY, 2004.