journal article·2010-01

Delamination Fracture Related to Tempering in a High-Strength Low-Alloy Steel

Wei Yan, Wei Sha, Lin Zhu, Wei Wang, Yi-Yin Shan, Ke Yang

Publisher page

Abstract

The delamination or splitting of mechanical test specimens of rolled steel plate is a phenomenon that has been studied for many years. In the present study, splitting during fracture of tensile and Charpy V-notch (CVN) test specimens is examined in a high-strength low-alloy plate steel. It is shown that delamination did not occur in test specimens from plate in the as-rolled condition, but was severe in material tempered in the temperature range 500 °C to 650 °C. Minor splitting was seen after heating to 200 °C, 400 °C, and 700 °C. Samples that had been triple quenched and tempered to produce a fine equiaxed grain size also did not exhibit splitting. Microstructural and preferred orientation studies are presented and are discussed as they relate to the splitting phenomenon. It is concluded that the elongated as-rolled grains and grain boundary embrittlement resulting from precipitates (carbides and nitrides) formed during reheating were responsible for the delamination.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Fatigue and fracture mechanics · Hydrogen embrittlement and corrosion behaviors in metals

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (35)

Show source-provided references
1. W. Wang, Y.Y. Shan, and K. Yang: Mater. Sci. Eng., A, 2009, vol. 502, pp. 38–44.10.1016/j.msea.2008.10.042 ↗
2. M.C. Zhao, Y.Y. Shan, F.R. Xiao, K. Yang, and Y.H. Li: Mater. Lett., 2002, vol. 57, pp. 141–45.10.1016/S0167-577X(02)00720-6 ↗
3. M. Yang, Y.J. Chao, X. Li, and J. Tan: Mater. Sci. Eng., A, 2008, vol. 497, pp. 451–61.10.1016/j.msea.2008.07.067 ↗
4. M. Yang, Y.J. Chao, X. Li, D. Immel, and J. Tan: Mater. Sci. Eng., A, 2008, vol. 497, pp. 462–70.10.1016/j.msea.2008.07.066 ↗
5. P. Shanmugam and S.D. Pathak: Eng. Fract. Mech., 1996, vol. 53, pp. 991–1005.10.1016/0013-7944(95)00159-X ↗
6. C. Thaulow, A.J. Paauw, A. Gunlleiksrud, and J. Troset: Eng. Fract. Mech., 1986, vol. 24, pp. 263–76.10.1016/0013-7944(86)90057-3 ↗
7. B. Faucher and B. Dogan: Metall. Trans. A, 1988, vol. 19A, pp. 505–16.10.1007/BF02649265 ↗
8. N. Tsuji, S. Okuno, Y. Koizumi, and Y. Minamino: Mater. Trans., 2004, vol. 45, pp. 2272–81.10.2320/matertrans.45.2272 ↗
9. R. Song, D. Ponge, and D. Raabe: Acta Mater., 2005, vol. 53, pp. 4881–92.10.1016/j.actamat.2005.07.009 ↗
10. R. Song, D. Ponge, D. Raabe, J.G. Speer, and D.K. Matlock: Mater. Sci. Eng., A, 2006, vol. 441, pp. 1–17.10.1016/j.msea.2006.08.095 ↗
11. K. Wallin: Int. J. Pressure Vessels Pip., 2001, vol. 78, pp. 463–70.10.1016/S0308-0161(01)00063-1 ↗
12. M.C. Silva, E. Hippert, Jr., and C. Ruggieri: Proc. ASME Pressure Vessels and Piping Conf., ASME, Denver, CO, 2005, pp. 87–94.
13. W. Guo, H. Dong, M. Lu, and X. Zhao: Int. J. Pressure Vessels Pip., 2002, vol. 79, pp. 403–12.10.1016/S0308-0161(02)00039-X ↗
14. X. Qingren, F. Yaorong, H. Chunyong, and L. Weiwei: Mater. Mech. Eng., 2005, vol. 29, pp. 21–25.
15. A. Ray, S.K. Paul, and S. Jha: J. Mater. Eng. Perform., 1995, vol. 4, pp. 679–88.10.1007/BF02646444 ↗
16. B.L. Bramfitt and A.R. Marder: Metall. Trans. A, 1977, vol. 8A, pp. 1263–73.10.1007/BF02643841 ↗
17. T. Otárola, S. Hollner, B. Bonnefois, M. Anglada, L. Coudreuse, and A. Mateo: Eng. Fail. Anal., 2005, vol. 12, pp. 930–41.10.1016/j.engfailanal.2004.12.022 ↗
18. J.I. Verdeja, J. Asensio, and J.A. Pero-Sanz: Mater. Charact., 2003, vol. 50, pp. 81–86.10.1016/S1044-5803(03)00106-2 ↗
19. K. Roessler: Neue Huette, 1989, vol. 34, pp. 254–57.
20. Y. Kimura, T. Inoue, F. Yin, O. Sitdikov, and K. Tsuzaki: Scripta Mater., 2007, vol. 57, pp. 465–68.10.1016/j.scriptamat.2007.05.039 ↗
21. X. Zhao, T.F. Jing, Y.W. Gao, G.Y. Qiao, J.F. Zhou, and W. Wang: Mater. Sci. Eng., A, 2005, vol. 397, pp. 117–21.10.1016/j.msea.2005.02.007 ↗
22. M. Pozuelo, F. Carreño, and O.A. Ruano: Compos. Sci. Technol., 2006, vol. 66, pp. 2671–76.10.1016/j.compscitech.2006.03.018 ↗
23. R. Schofield, G. Rowntree, N.V. Sarma, and R.T. Weiner: Met. Technol., 1974, vol. 1, pp. 325–31.10.1179/030716974803288112 ↗
24. C.S. da Costa viana and M.M. de Souza: Proc. 7th Int. Conf. Textures of Materials, Netherlands Society for Materials Science, Zwijndrecht, Netherlands, 1984, pp. 585–88.
25. C. Grobler and G.T. van Rooyen: Can. Metall. Q, 1988, vol. 27, pp. 49–58.10.1179/cmq.1988.27.1.49 ↗
26. T. Tanaka: Int. Met. Rev., 1981, vol. 4, pp. 185–212.
27. M.R. Krishnadev, S. Dionne, and J. Morrison: Mater. Charact., 1990, vol. 24, pp. 169–78.10.1016/1044-5803(90)90034-H ↗
28. A.J. McEvely and R.H. Rush: Trans. ASM, 1962, vol. 55, pp. 654–66.
29. R.D. Knutsen and R. Hutchings: Mater. Sci. Technol., 1988, vol. 4, pp. 127–35.10.1179/mst.1988.4.2.127 ↗
30. W. Yan, L. Zhu, W. Sha, Y.-Y. Shan, and K. Yang: Mater. Sci. Eng., A, 2009, vol. 517, pp. 369–74.10.1016/j.msea.2009.03.085 ↗
31. R.W.K. Honeycombe and H.K.D.H. Bhadeshia: Steels: Microstructure and Properties, 2nd ed., Arnold, London, 1995, p. 177.
32. W. Yan, Y.Y. Shan, and K. Yang: Metall. Mater. Trans. A, 2007, vol. 38A, pp. 1211–22.10.1007/s11661-007-9161-2 ↗
33. P.W. Bridgman: Studies in Large Plastic Flow and Fracture with Special Emphasis on the Effects of Hydrostatic Pressure, Harvard University Press, Cambridge, MA, 1964, pp. 9–8610.4159/harvard.9780674731349.c3 ↗
34. G.E. Dieter: Mechanical Metallurgy, 3rd ed., McGraw-Hill, New York, NY, 1986, p. 289.
35. D.L. Shu: Metal Mechanical Property, 2nd ed., China Machine Press, Beijing, 1997, p. 19.