The Deformation of Clad Aluminum Sheet Produced By Direct Chill Casting
Source abstract
Abstract
The tensile and bending response of AA3003/AA6111 sheet produced by direct chill casting has been investigated. It is shown that the interface strength of the clad sheet has a minimum value of 175 MPa, and failure does not occur in the interface. The yield strength of the clad sheet obeys the rule of mixtures, and up to a cladding thickness of 100 μm—which was the thickest investigated—the work hardening behavior and tensile response are essentially unaffected by the presence of the cladding. The bending response of the sheet is improved greatly by the presence of ductile cladding, which was the case for prestrained and aged sheet. Under bending, failure is initiated in the lower bendability core and then eventually propagates through the more ductile cladding, which yields the final bend failure.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties · Metal Forming Simulation Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (21)
Show source-provided references
1. R.B. Wagstaff, D.J. Lloyd, and T.F. Bischoff: Mater. Sci. Forum, 2006, vols. 519–521, pp. 1809–14.10.4028/www.scientific.net/MSF.519-521.1809 ↗
2. M.D. Anderson, K.T. Kubo, T.F. Bischoff, W.J. Fenton, E.W. Reeves, B. Spendlove, and R.B. Wagstaff: Patent US 7,472,740.
3. A.P. Kofman, P.O. Pashkov, and A.A. Yavor: Metalloveenie i Termicheskaya Obrabotka Metallov, 1966, no. 10, pp. 16–18.
4. A.G. Atkins and A.S. Weinstein: Int. J. Mech. Sci., 1970, vol. 12, pp. 641-57.10.1016/0020-7403(70)90094-9 ↗
5. E.A. Almond, J.D. Embury, and E.S. Wright: ASTM STP452, 1968, pp. 107–29.10.1520/STP44702S ↗
6. R. Hawkins and J.C. Wright: J. Inst. Metals, 1971, vol. 99, pp. 357-71.
7. C.K. Syn, D.R. Lesuer, J. Wolfenstine, and O.D. Sherby: Metall. Trans. A, 1993, vol. 24A, pp. 1647-53.10.1007/BF02646603 ↗
8. T. Mori and S. Kurimoto: J. Manuf. Sci. Eng., 1998, vol. 120, pp. 179-84.10.1115/1.2830098 ↗
9. A. Selcuk and R.D. Rawlings: J. Test. Evaluat., 1991, vol. 19, pp. 349-58.10.1520/JTE12586J ↗
10. D.J. Lloyd, D. Evans, C. Pelow, P. Nolan, and M. Jain: Mater. Sci. Technol., 2002, vol. 18, pp. 621-27.10.1179/026708302225003604 ↗
11. J. Sarkar, T.R.G. Kutty, D.S. Wilkinson, J.D. Embury, and D.J. Lloyd: Mater. Sci. Eng. A, 2004, vol. A369, pp. 258-66.10.1016/j.msea.2003.11.022 ↗
12. D.J. Lloyd: Proc. James T. Staley Symp. Al Alloys, ASM, Indianapolis, IN, 2001, pp. 161–65.
13. J.C. Halpin: Primer on Composite Materials: Analysis, Tecnomic Publishing Co. Inc., Lancaster, PA, 1984, pp. 35-67.
14. X.X. Chen, P.D. Wu, D.J. Lloyd, J.D. Embury, and Y. Huang: McMaster University, Hamilton, Ontario, unpublished research, 2009.
15. D.J. Lloyd: Scripta Mater., 2003, vol. 48, pp. 341-44.10.1016/S1359-6462(02)00455-4 ↗
16. J. Datsko and C.T. Yang: J. Eng. Ind. Trans. ASME, 1960, pp. 309–14.10.1115/1.3664236 ↗
17. J.D. Kuntz, G.-D. Zhan, and A.K. Mukherjee: MRS Bull., 2004, pp. 22–27.10.1557/mrs2004.12 ↗
18. J. Kajuch, J. Short, and J.J. Lewandowski: Acta Metall. Mater., 1995, vol. 43, pp. 1955-95.10.1016/0956-7151(94)00391-T ↗
19. L. Yost Ellis and J.J. Lewandowski: J. Mater. Sci. Let., 1991, vol. 10, pp. 461-63.10.1007/BF00838350 ↗
20. L. Yost Ellis and J.J. Lewandowski: Mater. Sci., Eng. A, 1994, vol. A183, pp. 59-67.10.1016/0921-5093(94)90890-7 ↗
21. R. Becker: J. Appl. Mech., 1992, vol. 59, pp. 491-96.10.1115/1.2893750 ↗