Quantification of Entrainment Damage in A356 Aluminum Alloy Castings
Source abstract
Abstract
Aluminum melts sustain damage to its quality when surface oxides are entrained into bulk liquid. To quantify the extent of entrainment damage, four castings were produced in reduced pressure test (RPT) apparatus; one machined out of the continuously cast ingot, and the other three by pouring the metal from a height of 25, 37.5, and 150 mm. Analyses of RPT samples via micro-computer tomography (μ-CT) scanning demonstrated that the number and volume fraction of pores in aluminum casting increased with increasing velocity of the liquid. However, average and maximum pore sizes first increased with velocity, then decreased, indicating that additional kinetic energy of the metal breaks entrained bifilms. The investigation of the cross sections of RPT specimens via scanning electron microscopy and X-ray maps showed that oxygen was present inside, around, and between the pores, providing further evidence that bifilms act as initiation sites for pores. Moreover, there were unopened bifilms near pores, suggesting that entrainment damage is more extensive than what can be ascertained by the pore size measurements.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Metallurgical Processes and Thermodynamics · Bauxite Residue and Utilization
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (41)
Show source-provided references
1. M. Tiryakioğlu, J. Campbell, and N. Green: Trans. Am. Foundrymen’s Soc., 1996, pp. 1069–78.
2. J.T. Staley Jr., M. Tiryakioğlu, and J. Campbell: Mater. Sci. Eng. A, 2007, 465(1), p. 136-145.10.1016/j.msea.2007.02.009 ↗
3. Tiryakioğlu, M.: Mater. Sci. Eng. A, 2009, 520(1), p. 114-120.10.1016/j.msea.2009.05.005 ↗
4. Tiryakioğlu, M.: Metall. Mater. Trans. A, 2009, 40(7), p. 1623-1630.10.1007/s11661-009-9847-8 ↗
5. Tiryakioğlu, M.: Mater. Sci. Eng. A, 2010, 527(6), p. 1560-1564.10.1016/j.msea.2009.10.027 ↗
6. Tiryakioğlu, M.: Mater. Sci. Eng. A, 2014, 601, p. 116-122.10.1016/j.msea.2014.02.033 ↗
7. Özdeş, H. and M. Tiryakioğlu: J. Mater. Eng. Perform., 2017, 26(2), p. 736-743.10.1007/s11665-016-2469-6 ↗
8. Wang Q., et al: Metall. Mater. Trans. B, 2006, 37, p. 887-895.10.1007/BF02735010 ↗
9. Tiryakioǧlu, M., J. Campbell, and J.T. Staley: Scr. Mater., 2003, 49(9), p. 873-878.10.1016/S1359-6462(03)00439-1 ↗
10. Tiryakioğlu, M., J. Campbell, and J.T. Staley: Mater. Sci. Eng. A, 2004. 368(1–2): p. 205-211.10.1016/j.msea.2003.10.311 ↗
11. Tiryakioğlu, M., J. Campbell, and N.D. Alexopoulos: Metall. Mater. Trans. A, 2009, 40(4), p. 1000-1007.10.1007/s11661-008-9762-4 ↗
12. Tiryakioğlu, M.: Mater. Sci. Eng. A, 2010, 527(18–19), p. 4546-4549.10.1016/j.msea.2010.03.109 ↗
13. Eisaabadi B, G., et al.: Mater. Sci. Eng. A, 2013, 579, p. 64-70.10.1016/j.msea.2013.05.014 ↗
14. Tiryakioğlu, M. and J. Campbell: Int. J. Metalcast., 2014, 8(3), p. 39-42.10.1007/BF03355589 ↗
15. Tiryakioğlu, M., J. Campbell, and N. D. Alexopoulos: Metall. Mater. Trans. B, 2009, 40, p. 802-811.10.1007/s11663-009-9304-5 ↗
16. L. Katgerman and D. G. Eskin: Hot Cracking Phenomena in Welds II, H.H. Thomas Bollinghaus, C.E. Cross, and J.C. Lippold, eds., Springer, Berlin, 2008, pp. 3–18.
17. Nazarboland, A. and R. Elliott: Int. J. Cast Met. Res., 1997, 10(2), p. 87-97.10.1080/13640461.1997.11819223 ↗
18. Campbell, J.: Mater. Sci. Technol., 2006, 22(2), p. 127-145.10.1179/174328406X74248 ↗
19. Dispinar D. and J. Campbell: Mater. Sci. Eng. A, 2011, 528, p. 3860-3865.10.1016/j.msea.2011.01.084 ↗
20. Yousefian P. and M. Tiryakioğlu: Metall. Mater. Trans. A, 2018, 49, p. 563-575.10.1007/s11661-017-4438-6 ↗
21. Uludağ M., R. Çetin, D. Dispinar, and M. Tiryakioğlu: Metals, 2017, 7, p. 1–16.10.3390/met7050157 ↗
22. J. Campbell: Le J. Phys. IV, vol. 03, pp. C7-861–C7-872, 1993.
23. Campbell, J.: Metall. Mater. Trans. B, 2011, 42(6), p. 1091-1097.10.1007/s11663-011-9575-5 ↗
24. Campbell, J.: Complete Casting Handbook: Metal Casting Processes, Metallurgy, Techniques and Design, 2015, Elsevier, Oxford.
25. W.F. Gale and T.C. Totemeier: Smithells Metals Reference Book, Elsevier, Oxford, 2003.
26. Runyoro J., S. Boutorabi, and J. Campbell: AFS Trans., 1992, 100, p. 225-234.
27. J. Campbell: Castings practice: the ten rules of castings, 2004, Elsevier, Oxford.
28. N. Lai, W. Griffiths, and J. Campbell: Modelling of Casting, Welding and Advanced Solidification Process X, D.M. Stefanescu et al., eds., TMS, Warrendale, 2003, pp. 415–22.
29. Mi J., R. A. Harding, and J. Campbell: Metall. Mater. Trans. A, 2004, 35, p. 2893-2902.10.1007/s11661-004-0237-y ↗
30. Taghiabadi R., M. Mahmoudi, M. Emamy Ghomy, and J. Campbell: Mater. Sci. Technol., 2003, 19, p. 497-502.10.1179/026708303225010821 ↗
31. Dai X., X. Yang, J. Campbell, and J. Wood: Mater. Sci. Technol., 2004, 20, p. 505-513.10.1179/026708304225012387 ↗
32. Weibull W.: J. Appl. Mech., 1951,18, p. 293-297.10.1115/1.4010337 ↗
33. Tiryakioğlu, M.: J. Mater. Sci., 2007, 43, p. 793-798.10.1007/s10853-007-2095-7 ↗
34. ASM International: Casting, vol. 15, ASM International, Materials Park, 1990, pp. 238–241.
35. Dvorak H. and E. Schwegtier: Int. J. Fract.Mech., 1972, 8, p. 110-111.10.1007/BF00185205 ↗
36. Tiryakioğlu, M.: Mater. Sci. Eng. A,2007, 465, p. 287-289.10.1016/j.msea.2007.02.008 ↗
37. M. Uludağ, R. Çetin, D. Dişpinar, and M. Tiryakioğlu: Int. J. Metalcast., 2018, pp. 1–8.
38. T.W. Anderson and D.A. Darling: J. Am. Stat. Assoc., 1954, 49, pp. 765-769.10.1080/01621459.1954.10501232 ↗
39. Murakami Y. and M. Endo: Int. J. Fatigue, 1994, 16, p. 163-182.10.1016/0142-1123(94)90001-9 ↗
40. Özdeş H. and M. Tiryakioğlu: Metals, 2016, 6, p. 1––9.10.3390/met6040081 ↗
41. Campbell, J.: Complete Casting Handbook: Metal Casting Processes, Metallurgy, Techniques and Design, 2011, Elsevier, Oxford .