Effect of Constraint on Creep Behavior of 9Cr-1Mo Steel
Source abstract
Abstract
The effect of constraint on creep rupture behavior of 9Cr-1Mo steel has been investigated. The constraint was introduced by incorporating a circumferential U-notch in a plain cylindrical creep specimen of 5 mm diameter. The degree of constraint was increased by decreasing the notch root radius from 5 to 0.25 mm. Creep tests were conducted on plain and notched specimens at stresses in the range of 110 to 210 MPa at 873 K (600 °C). The creep rupture life of the steel was found to increase under constrained conditions, which increased with the increase in degree of constraint and applied stress, and tended to saturate at a higher degree of constraint. The creep rupture ductility (pct reduction in area) of the steel was found to be lower under constrained conditions. The decrease in creep ductility was more pronounced at a higher degree of constraint and lower applied stresses. Scanning electron microscopic studies revealed a change in fracture behavior with stress and degree of constraint. The fracture surface appearance for relatively lower constrained specimens at higher stresses was predominantly transgranular dimple. Creep cavitation-induced intergranular brittle fracture near the notch root was observed for specimens having a higher degree of constraint at relatively lower stresses. The creep rupture life of the steel under constrained conditions has been predicted based on the estimation of damage evolution by continuum damage mechanics coupled with finite element analysis of the triaxial state of stress across the notch. It was found that the creep rupture life of the steel under constrained conditions was predominantly governed by the von-Mises stress and the principal stress became progressively important with increase in the degree of constraint and decrease in applied stress.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High Temperature Alloys and Creep · Fatigue and fracture mechanics · Material Properties and Failure Mechanisms
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (45)
Show source-provided references
1. D.R. Hayhurst: J. Mech. Phy. Solids, 1972, vol. 20, pp. 381- 390.10.1016/0022-5096(72)90015-4 ↗
2. B.F. Dyson and M. S. Loveday: in Proc. Creep in Structures, IUTAM Symp., A.R.S. Ponter and D.R. Hayhurst, ed., Pergamon Press, Oxford, 1981, pp. 406–421.10.1007/978-3-642-81598-0_27 ↗
3. K.D. Al-Faddagh, G.A. Webster, and B.F. Dyson: in Mechanical Behaviour of Materials IV, J. Carlsson and N.G. Ohlson, ed., Pergamon, Oxford, 1984, pp. 289–95.10.1016/B978-1-4832-8372-2.50033-6 ↗
4. S.E. Ng, G.A. Webster, and B.F. Dyson: in Advances in Fracture Research, ICF-5, D. Francois, ed., Pergamon, Oxford, 1981, pp. 1275–83.
5. G. Eggeler, W. Tato, P. Jemmely and B. deMestral: Scripta Metall. Mater., 1992, vol. 27, pp. 1091- 1096.10.1016/0956-716X(92)90479-X ↗
6. D.R. Hayhurst, F.A. Leckie and J.T. Henderson: Int. J. Mech. Sci., 1977, vol. 19, pp. 147- 159.10.1016/0020-7403(77)90074-1 ↗
7. D. Wu, E.M. Christian, E.G. Ellison: J. Strain Analysis, 1984, vol. 19, pp. 209-220.10.1243/03093247V194209 ↗
8. D.R. Hayhurst, J.T. Henderson: Int. J. Mech. Sci., 1977, vol. 19, pp. 133- 146.10.1016/0020-7403(77)90073-X ↗
9. B.J. Cane: in Advances in Fracture Research, ICF-5, D. Francois, ed., Pergamon, Oxford, 1981, pp. 1285–93.
10. D. McLean, B.F. Dyson, and D.M.R. Taplin: in 4th Int. Conf. on Fracture, D.M.R. Taplin, ed., University of Waterloo Press, Waterloo, 1977, pp. 325–62.10.1016/B978-0-08-022136-6.50032-9 ↗
11. D.R. Hayhurst and G.A. Webster: in Techniques for Multiaxial Creep Testing, D.J. Gooch and I.M. How, ed., Elsevier Applied Science, Amsterdam, 1986, pp. 137–75.10.1007/978-94-009-3415-3_9 ↗
12. T.H. Hyde, A.A. Becker, W. Sun and J.A. Williams: Int. J. Press. Vess. Piping, 2006, vol. 83, pp. 853- 863.10.1016/j.ijpvp.2006.08.013 ↗
13. T.H. Hyde, L. Xia and A.A. Becker: Int. J. Mech. Sci., 1996, vol. 38, pp. 385- 403.10.1016/0020-7403(95)00063-1 ↗
14. D.R. Hayhurst, P.R. Dimmer and C.J. Morrison: Phil. Trans. Royal Soc. Lon. A, 1984, vol. 311, pp. 103- 129.10.1098/rsta.1984.0021 ↗
15. A.M. Othman, D.R. Hayhurst and B.F. Dyson: Proc. Royal Soc. Lond. A, 1993, vol. 441, pp. 343- 358.10.1098/rspa.1993.0065 ↗
16. G.A. Webster, S.R. Holdsworth, M.S. Loveday, K. Nikbin, I.J. Perrin, H. Purper, R.P. Skelton and M.W. Spindler: Fat. Frac. Engg Mater. Struct., 2004, vol. 27, pp. 319- 342.10.1111/j.1460-2695.2004.00765.x ↗
17. B. Al-Abed, R. Timmins, G.A. Webster and M. S. Loveday: Materials at High Temperature, 1999, vol. 16, pp. 143-158.10.3184/096034099783641155 ↗
18. O. Kwon, C.W. Thomas, D. Knowles: Int. J. Press. Vess. Piping, 2004, vol. 81, pp. 535- 542.10.1016/j.ijpvp.2003.12.023 ↗
19. W.D. Nix, J.C. Earthman, G. Eggeler and B. Ilschner: Acta Metallurgica, 1989, vol. 37, pp. 1067- 1077.10.1016/0001-6160(89)90103-X ↗
20. T.H. Hyde, W. Sun and A.A. Becker: Int. J Mech. Sci., 2000, vol. 42, pp. 401- 423.10.1016/S0020-7403(99)00008-9 ↗
21. G.A.Webster, K.M. Nikbin, and F. Biglari: Fat. Frac. Eng. Mater. Struct., 2004, vol. 27, pp. 297-303.10.1111/j.1460-2695.2004.00704.x ↗
22. B.J. Cane: in Proceedings of the Int. Conf. on Mechanical behavior of Materials, K.J. Miller and R.F. Smith, ed., Pergamon, Oxford, 1979, pp. 173–82.
23. R.L. Huddleston: J. Press. Vessel Technol., 1985, vol. 107, pp. 412- 429.10.1115/1.3264476 ↗
24. J. Lemaitre and J.-L. Chaboche, Mechanics of solid materials, Cambridge University Press, Cambridge, 1990.10.1017/CBO9781139167970 ↗
25. A. Baldev Raj, S.L. Mannan, P.R. Vasudeva Rao and M.D. Mathew: Sadhana, 2002, vol. 27, pp. 527–558.10.1007/BF02703293 ↗
26. S.C. Chetal, P. Chellapandi, P. Puthiyavinayagam, S. Raghupathy, V. Balasubramaniyan, P. Selvaraj, P. Mohankrishnan, and B. Raj: Energy Procedia, 2011, vol. 7, pp. 64-73.10.1016/j.egypro.2011.06.009 ↗
27. W.D. Pilkey and D.F. Pilkey, Peterson’s Stress Concentration Factors, 3rd Edition, Wiley, Hoboken, NJ, 2008.
28. C.R. Calladine: Proc. Royal Soc. Lond. A, 1969, vol. 309, pp. 363-375.10.1098/rspa.1969.0047 ↗
29. L.M. Kachanov: in The Theory of Creep, A.J. Kennedy, ed., National Lending Library, Boston, 1967.
30. F. Abe, S. Nakazawa, H. Araki and T. Noda: Metall. Trans. A, 1992, vol. 23A, pp. 469- 477.10.1007/BF02801164 ↗
31. B.K. Choudhary, S. Saroja, K. Bhanu Sankara Rao, and S.L. Mannan: Metall. Trans. A, 1999, vol. 30A, pp. 2825-2834.10.1007/s11661-999-0120-y ↗
32. E.I. Samuel, B.K. Choudhary, K. Bhanu Sankara Rao, and B. Raj: Pressure Vessels and Piping: Materials and Properties, Narosa Publishing House, New Delhi, 2008, pp. 83-100.
33. F.A. Leckie, D.R. Hayhurst: Acta Metall., 1977, vol. 25, pp. 1059- 1070.10.1016/0001-6160(77)90135-3 ↗
34. M.F. Ashby and B.F. Dyson: in Advances in Fracture Research, R.S. Valluri, ed., Pergamon, Oxford, 1984, pp. 3–30.10.1016/B978-1-4832-8440-8.50017-X ↗
35. B.F. Dyson, T.B. Gibbons: Acta Metall., 1987, vol. 35, pp. 2355- 2369.10.1016/0001-6160(87)90083-6 ↗
36. P. Lukas, P. Preclik, J. Cadek: Mat. Sci. Engg. A, 2001, vol. 298, pp. 84- 89.10.1016/S0921-5093(00)01288-0 ↗
37. S. Goyal, K. Laha, K.S. Chandravathi, P. Parameswaran, and M.D. Mathew: Philos. Mag., 2011, vol. 91, pp. 3128-3154.10.1080/14786435.2011.570279 ↗
38. I.J. Perrin, D.R. Hayhurst: Int. J. Press. Vess. Piping, 1999, vol. 76, pp. 599-617.10.1016/S0308-0161(99)00051-4 ↗
39. J.W. Hancock: Met. Sci., 1976, vol. 10, pp. 319-325.10.1016/0036-9748(76)90084-3 ↗
40. F.A. McClintock: J. App. Mech., 1968, vol. 35, pp. 363- 371.10.1115/1.3601204 ↗
41. D. Hull and D.E. Rimmer: Phil. Mag., 1959, vol. 4, pp. 673- 687.10.1080/14786435908243264 ↗
42. M.F. Ashby, C. Gandhi and D.M.R. Taplin: Acta. Metall., 1979, vol. 27, pp. 699–729.10.1016/0001-6160(79)90105-6 ↗
43. J. Hancock: in Topics in Fracture and Fatigue, A. Argon, Springer, New York, NY, 1992, pp 99–144.10.1007/978-1-4612-2934-6_3 ↗
44. J.R. Rice and D.M, Tracey: J. Mech. Phy. Solids, 1969, vol. 17, pp. 201-217.10.1016/0022-5096(69)90033-7 ↗
45. A.C.F. Cocks and M.F. Ashby: Met. Sci., 1980, vol. 14, pp. 395- 402.10.1179/030634580790426148 ↗