journal article·2013-01

Microstructure Evolution in an Advanced 9 pct Cr Martensitic Steel during Creep at 923 K (650 °C)

Irina Fedorova, Alla Kipelova, Andrey Belyakov, Rustam Kaibyshev

Publisher page

Abstract

Crept microstructures were examined in a 9 pct Cr martensitic steel with low carbon content. The steel was hot forged at 1323 K (1050 °C) followed by air cooling and then tempered at 1023 K (750 °C) for 3 hours. The tempered microstructure included numerous precipitates of MX-type carbonitrides and a small amount of M23C6-type carbides. Two groups of the MX-type particles were observed. The nanoscale MX-type precipitates appeared in the form of plate- and round-shaped particles. The plate-shaped MX-type particles were approximately 15 nm in the longitudinal direction and approximately 3 nm in thickness, and the round-shaped MX-type particles were 10 nm in diameter. In addition to the fine particles, the tempered martensite contained relatively coarse MX-type particles, which have a size of approximately 90 nm. The structural changes that occurred during the creep test were associated with an increase in the sizes of the lath and second-phase particles. Moreover, the creep was accompanied by appearance of Laves and Z-phase particles.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High Temperature Alloys and Creep · Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (26)

Show source-provided references
1. F. Masuyama: ISIJ Int., 2001, vol. 41, pp. 612–25.10.2355/isijinternational.41.612 ↗
2. P.J. Ennis and A. Czyrska-Filemonowicz: Sadhana, 2003, vol. 28, pp. 709–30.10.1007/BF02706455 ↗
3. K. Kimura, K. Sawada, H. Kushima, and K. Kubo: Int. J. Mater. Res., 2008, vol. 99, pp. 395–401.10.3139/146.101651 ↗
4. J.C. Vaillant, B. Vandenberghe, B. Hahn, H. Heuser, and C. Jochum: Int. J. Press. Ves. Pip., 2008, vol. 85, pp. 38–46.10.1016/j.ijpvp.2007.06.011 ↗
5. R.O. Kaybyshev, V.N. Skorobogatykh, and I.A. Shchenkova: Phys. Met. Metallogr., 2010, vol. 109, pp. 186–200.10.1134/S0031918X10020110 ↗
6. J.M. Vitek and R.L. Klueh: Metall. Trans. A, 1993, vol. 14A, pp. 1047–55.
7. V. Sklenicka, K. Kucharova, M. Svoboda, L. Kloc, J. Bursik, and A. Kroupa: Mater. Charact., 2003, vol. 51, pp. 35–48.10.1016/j.matchar.2003.09.012 ↗
8. D. Rojas, J. Garcia, O. Prat, G. Sauthoff, and A.R. Kaysser-Pyzalla: Mater. Sci. Eng. A, 2011, vol. 528A, pp. 5164–76.10.1016/j.msea.2011.03.037 ↗
9. A. Kostka, K.-G. Tak, R.J. Hellmig, Y. Estrin, and G. Eggeler: Acta Mater., 2007, vol. 55, pp. 539–50.10.1016/j.actamat.2006.08.046 ↗
10. H.G. Armaki, R. Chen, K. Maruyama, and M. Igarashi: Mater. Sci. Eng. A, 2010, vol. A527, pp. 6581–88.10.1016/j.msea.2010.07.037 ↗
11. F. Abe: Mater. Sci. Eng. A, 2004, vol. 387–389A, pp. 565–69.10.1016/j.msea.2004.01.057 ↗
12. H. Chilukuru, K. Durst, S. Wadekar, M. Schwienheer, A. Scholz, C. Berger, K.H. Mayer, and W. Blum: Mater. Sci. Eng. A, 2009, vol. 510–511A, pp. 81–87.10.1016/j.msea.2008.04.088 ↗
13. A. Aghajani, C. Somsen, and G. Eggeler: Acta Mater., 2009, vol. 57, pp. 5093–5106.10.1016/j.actamat.2009.07.010 ↗
14. A. Gustafson and M. Hattestrand: Mater. Sci. Eng. A, 2002, vol. 333A, pp. 279–86.10.1016/S0921-5093(01)01874-3 ↗
15. A. Kipelova, R. Kaibyshev, A. Belyakov, and D. Molodov: Mater. Sci. Eng. A, 2011, vol. 528A, pp. 1280–86.10.1016/j.msea.2010.10.006 ↗
16. H.K. Danielsen, J. Hald, F.B. Grumsen, and M.A.J. Somers: Metall. Mater. Trans. A, 2006, vol. 37A, pp. 2633–40.10.1007/BF02586098 ↗
17. H.K. Danielsen and J. Hald: Mater. Sci. Eng. A, 2009, vol. 505A, pp. 169–77.10.1016/j.msea.2008.11.019 ↗
18. K. Sawada, H. Kushima, M. Tabuchi, and K. Kimura: Mater. Sci. Eng. A, 2011, vol. 528, pp. 5511–18.10.1016/j.msea.2011.03.073 ↗
19. G. Dimmler, P. Weinert, E. Kozeschnik, and H. Cerjak: Mater. Charact., 2003, vol. 51, pp. 341–52.10.1016/j.matchar.2004.02.003 ↗
20. M. Taneike, F. Abe, and K. Sawada: Nature, 2003, vol. 424, pp. 294–96.10.1038/nature01740 ↗
21. F. Abe, T. Horiuchi, M. Taneike, and K. Sawada: Mater. Sci. Eng. A, 2004, vol. 378, pp. 299–303.10.1016/j.msea.2003.11.073 ↗
22. F. Abe, M. Taneike, and K. Sawada: Int. J. Press. Ves. Pip., 2007, vol. 84, pp. 3–12.10.1016/j.ijpvp.2006.09.003 ↗
23. F.-S. Yin and W.-S. Jung: Metall. Mater. Trans. A, 2009, vol. 40A, pp. 302–09.10.1007/s11661-008-9716-x ↗
24. D.B. Williams and C.B. Carter: Transmission Electron Microscopy, Plenum Press, New York, NY, 1996, pp. 361–64.10.1007/978-1-4757-2519-3 ↗
25. V.A. Dudko, A.N. Belyakov, V.N. Skorobogatykh, I.A. Shchenkova, and R.O. Kaibyshev: Met. Sci. Heat Treat., 2010, vol. 52, pp. 111–17.10.1007/s11041-010-9241-6 ↗
26. J. Hald: Int. J. Press. Ves. Pip., 2008, vol. 85, pp. 30–37.10.1016/j.ijpvp.2007.06.010 ↗