journal article·2021-03Open access

Strain Rate Dependent Ductility and Strain Hardening in Q&P Steels

Christopher B. Finfrock, Melissa M. Thrun, Diptak Bhattacharya, Trevor J. Ballard, Amy J. Clarke, Kester D. Clarke

Abstract

Due to their high strength, formability and affordable cost, quenched and partitioned (Q&P) steels have shown the potential to reduce the mass of vehicles, thereby decreasing fuel consumption during service. Furthermore, because a lower mass of steel is used in each vehicle, energy consumption associated with the steelmaking process is also reduced. Q&P steels utilize the deformation-induced martensitic transformation (DIMT) of metastable retained austenite to enhance ductility and strain hardening. Accordingly, improvement of mechanical performance is contingent on the ability to precisely control the chemical and mechanical stability of austenite. Considering the multitude of factors that influence austenite stability, optimizing microstructures to delay necking or fracture is challenging, particularly as temperature and strain rate increase. Tensile tests of an intercritically annealed C-Mn-Si Q&P steel were performed over a range of strain rates (10−4 to 10−1 s−1) to evaluate effects on the DIMT and sheet tensile properties. As strain rates increased from 10−4 to 10−1 s−1, the uniform elongation decreased from approximately 19 to 14 pct. This reduction in uniform elongation is associated with a decrease in the strain hardening exponent near the onset of strain localization. Based on experimental data from this study and review of previous research, it is postulated that the strengthening contribution of DIMT is controlled by competing effects of: (i) a decreasing chemical driving force for DIMT caused by deformation-induced heat accumulation at higher strain rates and (ii) an increasing number of martensite nucleation sites. This suggests that tailoring austenite stability for specific deformation conditions could enable further optimization of formability and vehicle crash behavior.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Metallurgy and Material Forming

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (100+)

Show source-provided references
1. 1 H. Helms and U. Lambrecht: The International Journal of Life Cycle Assessment, 2007, vol. 12, pp. 58-64.
2. 2 D. Raabe, C.C. Tasan, and E.A. Olivetti: Nature, 2019, vol. 575, pp. 64-74.10.1038/s41586-019-1702-5 ↗
3. A.D. Brooker, J. Ward, and L. Wang: SAE Technical Papers, Technical Report No. 2013-01-0381, https://doi.org/10.4271/2013-01-0381.10.4271/2013-01-0381 ↗
4. 4 H.C. Kim and T.J. Wallington: Environmental Science and Technology, 2013, vol. 47, pp. 14358-66.10.1021/es402954w ↗
5. 5 O. Bouaziz, H. Zurob, and M. Huang: Steel Research International, 2013, vol. 84, pp. 937-47.10.1002/srin.201200288 ↗
6. D.K. Matlock and J.G. Speer (2009). In: A. Haldar, S. Suwas, and D. Bhattacharjee, eds., Microstructure and Texture in Steels. Springer, London, pp. 185-205.10.1007/978-1-84882-454-6_11 ↗
7. P. Russo, M. Maddis, G. Dtonio, and F. Lombardi (2016) Metals 4:7. https://doi.org/10.3390/met6110270.10.3390/met6110270 ↗
8. P. RussoSpena, L. Cortese, M. De Maddis, and F. Lombardi: Steel Research International, 2016, vol. 87, pp. 1592-600.10.1002/srin.201600007 ↗
9. K.M. Molnar: Colorado School of Mines, 2020.
10. 10 D. Bhattacharya: Materials Science and Technology, 2018, vol. 34, pp. 1809-29.10.1080/02670836.2018.1461595 ↗
11. 11 J. Speer, D.K. Matlock, B.C. De Cooman, and J.G. Schroth: Acta Materialia, 2003, vol. 51, pp. 2611-22.10.1016/S1359-6454(03)00059-4 ↗
12. A.M. Streicher, J.G. Speer, D.K. Matlock, and B.C. De Cooman: in International Conference on Advanced High-Strength Sheet Steels for Automotive Applications, Winter Park, Colorado, 2004, pp. 51–62.
13. 13 D. V. Edmonds, K. He, F.C. Rizzo, B.C. De Cooman, D.K. Matlock, and J.G. Speer: Materials Science and Engineering A, 2006, vol. 438-440, pp. 25-34.10.1016/j.msea.2006.02.133 ↗
14. 14 A.J. Clarke, J.G. Speer, M.K. Miller, R.E. Hackenberg, D. V. Edmonds, D.K. Matlock, F.C. Rizzo, K.D. Clarke, and E. De Moor: Acta Materialia, 2008, vol. 56, pp. 16-22.10.1016/j.actamat.2007.08.051 ↗
15. 15 L. Wang and J.G. Speer: Metallography, Microstructure, and Analysis, 2013, vol. 2, pp. 268-81.10.1007/s13632-013-0082-8 ↗
16. 16 F.D. Fischer, G. Reisner, E. Werner, K. Tanaka, G. Cailletaud, and T. Antretter: International Journal of Plasticity, 2000, vol. 16, pp. 723-48.10.1016/S0749-6419(99)00078-9 ↗
17. W. Bleck, X. Guo, and Y. Ma: Steel Res. Int., 2017, vol. 88, https://doi.org/10.1002/srin.201700218.10.1002/srin.201700218 ↗
18. 18 G.W. Greenwood and R.H. Johnson: Proceedings of the Royal Society A: Mathematical, Physical and Engineering Sciences, 1965, vol. 283, pp. 403-22.
19. C.L. Magee: Carnegie Institute of Technologie University Ph.D Thesis, 1966.
20. 20 E. De Moor, S. Lacroix, A.J. Clarke, J. Penning, and J.G. Speer: Metall. Mater. Trans. A, 2008, vol. 39, pp. 2586-95.10.1007/s11661-008-9609-z ↗
21. E. De Moor, J.G. Speer, D.K. Matlock, and D.N. Hanlon: in Contributed Papers from Materials Science & Technology (MS&T11), 2011, pp. 568–79.
22. 22 C.B. Finfrock, A.J. Clarke, G.A. Thomas, and K.D. Clarke: Metall. Mater. Trans. A, 2020, vol. 51, pp. 2025-34. https://doi.org/10.1007/s11661-020-05666-810.1007/s11661-020-05666-8 ↗
23. 23 P.J. Gibbs, E. De Moor, M.J. Merwin, B. Clausen, J.G. Speer, and D.K. Matlock: Metall. Mater. Trans. A, 2011, vol. 42, pp. 3691-702.10.1007/s11661-011-0687-y ↗
24. 24 J.G. Speer, E. De Moor, K.O. Findley, D.K. Matlock, B.C. De Cooman, and D. V. Edmonds: Metall. Mater. Trans. A, 2011, vol. 42, pp. 3591-601.10.1007/s11661-011-0869-7 ↗
25. 25 J. Hidalgo, K.O. Findley, and M.J. Santofimia: Materials Science and Engineering A, 2017, vol. 690, pp. 337-47.10.1016/j.msea.2017.03.017 ↗
26. 26 K.O. Findley, J. Hidalgo, R.M. Huizenga, and M.J. Santofimia: Materials and Design, 2017, vol. 117, pp. 248-56.10.1016/j.matdes.2016.12.065 ↗
27. 27 J. Kähkönen, D.T. Pierce, J.G. Speer, E. de Moor, G.A. Thomas, D. Coughlin, K. Clarke, and A. Clarke: JOM, 2015, vol. 68, pp. 210-4.10.1007/s11837-015-1620-4 ↗
28. 28 G.A. Thomas, J.G. Speer, and D.K. Matlock: Metall. Mater. Trans. A, 2011, vol. 42, pp. 3652-9.10.1007/s11661-011-0648-5 ↗
29. 29 E. Emadoddin, H. Asmari, and A.H. Zadeh: International Journal of Material Forming, 2009, vol. 2, pp. 781-4.10.1007/s12289-009-0455-3 ↗
30. 30 S.S. Hecker, M.G. Stout, K.P. Staudhammer, and J.L. Smith: Metallurgical Transactions A, 1982, vol. 13, pp. 619-26.10.1007/BF02644427 ↗
31. 31 L.E. Murr, K.P. Staudhammer, and S.S. Hecker: Metallurgical Transactions A, 1982, vol. 13, pp. 627-35.10.1007/BF02644428 ↗
32. A.M. Streicher: Colorado School of Mines M.S. Thesis, 2002.
33. C. Chiriac, R. Sohmshetty, J. Balzer, T. Mueller, and J.D. Ju (2004) IOP Conf. Ser. https://doi.org/10.1088/1757-899x/418/1/012004.10.1088/1757-899x/418/1/012004 ↗
34. 34 J.Y. Lee, L. Xu, F. Barlat, R.H. Wagoner, and M.G. Lee: Experimental Mechanics, 2013, vol. 53, pp. 1681-92.10.1007/s11340-013-9758-x ↗
35. 35 J. He, G. Han, S. Li, and D. Zou: International Journal of Mechanical Sciences, 2019, vol. 152, pp. 198-210.10.1016/j.ijmecsci.2019.01.003 ↗
36. 36 W. Wu, Y.W. Wang, P. Makrygiannis, F. Zhu, G.A. Thomas, L.G. Hector, X. Hu, X. Sun, and Y. Ren: Materials Science and Engineering A, 2018, vol. 711, pp. 611-23.10.1016/j.msea.2017.11.008 ↗
37. 37 A.K. Ghosh: Journal of Engineering Materials and Technology, 1977, vol. 99, pp. 264-74.10.1115/1.3443530 ↗
38. R. Alturk, L.G. Hector, C. MatthewEnloe, F. Abu-Farha, and T.W. Brown (2018) JOM. vol. 70, pp. 894-905.10.1007/s11837-018-2830-3 ↗
39. 39 X. Yang, L.G. Hector, and J. Wang: Experimental Mechanics, 2014, vol. 54, pp. 775-89.10.1007/s11340-014-9850-x ↗
40. W. Poling: Colorado School of Mines Ph.D Thesis, 2017.
41. 41 J.T. Benzing, W.A. Poling, D.T. Pierce, J. Bentley, K.O. Findley, D. Raabe, and J.E. Wittig: Materials Science and Engineering A, 2018, vol. 711, pp. 78-92.10.1016/j.msea.2017.11.017 ↗
42. C. Finfrock, C.G. Becker, T. Ballard, G. Thomas, K. Clarke, and A. Clarke: in Contributed Papers from Materials Science & Technology (MS&T19), Portland, Oregon, 2019, pp. 1236–43. https://doi.org/10.7449/2019/mst_2019_1236_1243.10.7449/2019/mst_2019_1236_1243 ↗
43. K.D. Clarke: Colorado School of Mines M.S. Thesis, 2002.
44. K.D. Clarke, R.J. Comstock, M.C. Mataya, D.K. Matlock, J.G. Speer, and G.P. Martins: SAE Technical Papers, Technical Report No. 2003-01-0526, https://doi.org/10.4271/2003-01-0526.10.4271/2003-01-0526 ↗
45. D.A. Porter and K.E. Easterling: Phase Transformations in Metals and Alloys, 2nd edn, Springer, New York. 1992.10.1007/978-1-4899-3051-4 ↗
46. 46 G.F. Bolling and R.H. Richman: Scripta Metallurgica, 1970, vol. 4, pp. 539-44.10.1016/0036-9748(70)90012-8 ↗
47. 47 G.B. Olson and C. Morris: Journal of the Less-Common Metals, 1972, vol. 28, pp. 107-18.10.1016/0022-5088(72)90173-7 ↗
48. 48 Z. Wang and M.X. Huang: Metall. Mater. Trans. A, 2019, vol. 50, pp. 5650-5.10.1007/s11661-019-05465-w ↗
49. 49 K. Sugimoto, M. Kobayashi, and S. Hashimoto: Metall. Mater. Trans. A, 1992, vol. 23A, pp. 3085-91.10.1007/BF02646127 ↗
50. 50 B.C. De Cooman: Current Opinion in Solid State and Materials Science, 2004, vol. 8, pp. 285-303.10.1016/j.cossms.2004.10.002 ↗
51. 51 W. Feng, Z. Wu, L. Wang, and J.G. Speer: Steel Research International, 2013, vol. 84, pp. 246-52.10.1002/srin.201200129 ↗
52. 52 G.B. Olson and M. Cohen: Metallurgical Transactions A, 1975, vol. 6A, pp. 791-5.10.1007/BF02672301 ↗
53. 53 W.J. Dan, W.G. Zhang, S.H. Li, and Z.Q. Lin: Computational Materials Science, 2007, vol. 40, pp. 101-7.10.1016/j.commatsci.2006.11.006 ↗
54. 54 J. Talonen, P. Nenonen, G. Pape, and H. Hänninen: Metall. Mater. Trans. A, 2005, vol. 36A, pp. 421-32.10.1007/s11661-005-0313-y ↗
55. M. Bhargava, S. Chakrabarty, V. Kumar, A. Tewari, and S.K. Mishra: 2018, vol. 152, pp. 65–77.10.1016/j.matdes.2018.04.068 ↗
56. ASTM International E8/E8M-16a, https://doi.org/10.1520/e0008_e0008m-16a.10.1520/e0008_e0008m-16a ↗
57. 57 G.E. Dieter: Mechanical Metallurgy, 3rd edn., McGraw-Hill, New York, NY, 1961.
58. 58 B.K. Jha, R. Avtar, V.S. Dwivedi, and V. Ramaswamy: Journal of Materials Science Letters, 1987, vol. 6, pp. 891-3.10.1007/BF01729860 ↗
59. ASTM International E975-13, https://doi.org/10.1520/e0975-13.10.1520/e0975-13 ↗
60. 60 B.D. Cullity: Elements of X-Ray Diffraction, 1st edn., Addison-Wesley Publishing Company, Inc., Reading, Massachusetts, 1956.
61. 61 W. Li, H. Gao, H. Nakashima, S. Hata, and W. Tian: Materials Characterization, 2016, vol. 118, pp. 431-7.10.1016/j.matchar.2016.06.020 ↗
62. 62 P. Haasen and A. Kelly: Acta Metallurgica, 1957, vol. 5, pp. 192-9.10.1016/0001-6160(57)90165-7 ↗
63. 63 L.M. Brown: Philosophical Magazine, 2010, vol. 90, pp. 4147-52.10.1080/14786431003705355 ↗
64. 64 D. Hull and D.J. Bacon: Introduction to Dislocations, 5th edn., Elsevier, Burlington, MA, 2011.
65. 65 D.M. Field and D.C. Van Aken: Metall. Mater. Trans. A, 2018, vol. 49, pp. 1152-66.10.1007/s11661-018-4481-y ↗
66. 66 T. Waterschoot, A.K. De, S. Vandeputte, and B.C. De Cooman: Metall. Mater. Trans. A: Physical Metallurgy and Materials Science, 2003, vol. 34, pp. 781-91.10.1007/s11661-003-1006-z ↗
67. 67 R.W. Rathbun, D.K. Matlock, and J.G. Speer: Scripta Materialia, 2000, vol. 42, pp. 887-91.10.1016/S1359-6462(00)00308-0 ↗
68. M. Thrun, C. Finfrock, A. Clarke, and K. Clarke (2020) Front. Mater. Struct. Mater. 7, 615361.
69. 69 J. Min, L.G. Hector, L. Zhang, L. Sun, J.E. Carsley, and J. Lin: Materials and Design, 2016, vol. 95, pp. 370-86.10.1016/j.matdes.2016.01.113 ↗
70. 70 Q. Hao, S. Qin, Y. Liu, X. Zuo, N. Chen, W. Huang, and Y. Rong: Materials Science and Engineering A, 2016, vol. 662, pp. 16-25.10.1016/j.msea.2016.03.007 ↗
71. 71 F. Abu-Farha, X. Hu, X. Sun, Y. Ren, L.G. Hector, G. Thomas, and T.W. Brown: Metallurgical & Materials Transactions A, 2018, vol. 49A, pp. 2583-96.10.1007/s11661-018-4660-x ↗
72. 72 X.H. Hu, X. Sun, L.G. Hector, and Y. Ren: Acta Materialia, 2017, vol. 132, pp. 230-44.10.1016/j.actamat.2017.04.028 ↗
73. 73 A.K. Ghosh: Acta Metallurgica, 1977, vol. 25, pp. 1413-24.10.1016/0001-6160(77)90072-4 ↗
74. G.C. Soares, B.M. Gonzalez, and L. de ArrudaSantos: Mater. Sci. Eng. A 2017, vol. 684, pp. 577-85.10.1016/j.msea.2016.12.094 ↗
75. 75 A. Skowronek and A. Grajcar: Materials, 2020, vol. 13, pp. 25-40.
76. 76 D. Salehiyan, J. Samei, B.S. Amirkhiz, L.G. Hector, and D.S. Wilkinson: Metall. Mater. Trans. A, 2020, vol. 51, pp. 4524-39.10.1007/s11661-020-05882-2 ↗
77. D.S. Connolly, C.P. Kohar, W. Muhammad, L.G. Hector, R.K. Mishra, and K. Inal (2020) Int. J. Plast. 5:9. https://doi.org/10.1016/j.ijplas.2020.102757.10.1016/j.ijplas.2020.102757 ↗
78. 78 G.I. Taylor and H. Quinney: Proceedings of the Royal Society of London. Series A, Containing Papers of a Mathematical and Physical Character, 1934, vol. 143, pp. 307-26.10.1098/rspa.1934.0004 ↗
79. 79 A. Andrade-Campos, F. Teixeira-Dias, U. Krupp, F. Barlat, E.F. Rauch, and J.J. Grácio: Strain, 2010, vol. 46, pp. 283-97.10.1111/j.1475-1305.2008.00572.x ↗
80. W.D. Callister and D.G. Rethwisch: Materials Science and Engineering: An Introduction, 10th edn. Wiley Global Education, New York. 2018.
81. 81 N.I. Vazquez-Fernandez, G.C. Soares, J.L. Smith, J.D. Seidt, M. Isakov, A. Gilat, V.T. Kuokkala, and M. Hokka: Journal of Dynamic Behavior of Materials, 2019, vol. 5, pp. 221-9.10.1007/s40870-019-00204-z ↗
82. 82 H. Kim, J. Lee, F. Barlat, D. Kim, and M.G. Lee: Acta Materialia, 2015, vol. 97, pp. 435-44.10.1016/j.actamat.2015.06.023 ↗
83. J. Coryell, V. Savic, L. Hector, and S. Mishra: SAE Technical Papers Technical Report No. 2013-01-0610, https://doi.org/10.4271/2013-01-0610.10.4271/2013-01-0610 ↗
84. 84 R. Rana, E. De Moor, J.G. Speer, and D.K. Matlock: JOM, 2018, vol. 70, pp. 706-13.10.1007/s11837-018-2779-2 ↗
85. 85 D.Q. Zou, S.H. Li, and J. He: Materials Science and Engineering A, 2017, vol. 680, pp. 54-63.10.1016/j.msea.2016.10.083 ↗
86. C. Enloe, V. Savic, W. Poling, L. Hector, and R. Alturk: SAE Technical Papers, Technical Report No. 2019-01-0521, 2019, pp. 1–10.
87. V. Savic, L. Hector, R. Alturk, and C. Enloe: SAE Technical Papers, Technical Report No. 2020-01-0754, 2020, pp. 1–8.
88. 88 X. Yang, X. Xiong, Z. Yin, H. Wang, J. Wang, and D. Chen: Experimental Mechanics, 2014, vol. 54, pp. 641-52.10.1007/s11340-013-9828-0 ↗
89. 89 H. Wang, W. Zhang, D. Ma, B. Ma, D. Chen, X. Yang, and C. Fan: Acta Mechanica Solida Sinica, 2017, vol. 30, pp. 484-92.10.1016/j.camss.2017.09.003 ↗
90. Y. Gao, C. Xu, Z. P. He, Y. L. He, and L. Li: Journal of Iron and Steel Research International, 2015, vol. 22, pp. 48-54.10.1016/S1006-706X(15)60008-5 ↗
91. 91 P.J. Jacques, S. Allain, O. Bouaziz, A. De, A.-F. Gourgues, B.M. Hance, Y. Houbaert, J. Huang, A. Iza-Mendia, S.E. Kruger, M. Radu, L. Samek, J. Speer, L. Zhao, and S. van der Zwaag: Materials Science and Technology, 2009, vol. 25, pp. 567-74.10.1179/174328408X353723 ↗
92. 92 T. Gnäupel-Herold and A. Creuziger: Materials Science and Engineering A, 2011, vol. 528, pp. 3594-600.10.1016/j.msea.2011.01.030 ↗
93. 93 X.C. Xiong, B. Chen, M.X. Huang, J.F. Wang, and L. Wang: Scripta Materialia, 2013, vol. 68, pp. 321-4.10.1016/j.scriptamat.2012.11.003 ↗
94. 94 D. De Knijf, C. Föjer, L.A.I. Kestens, and R. Petrov: Materials Science and Engineering A, 2015, vol. 638, pp. 219-27.10.1016/j.msea.2015.04.075 ↗
95. 95 M. Wang and M.X. Huang: Acta Materialia, 2020, vol. 188, pp. 551-9.10.1016/j.actamat.2020.02.035 ↗
96. 96 C. Liu, L. Wang, and Y. Liu: Materials Science Forum, 2013, vol. 749, pp. 401-6.10.4028/www.scientific.net/MSF.749.401 ↗
97. 97 K. Zhang, M. Zhang, Z. Guo, N. Chen, and Y. Rong: Materials Science and Engineering A, 2011, vol. 528, pp. 8486-91.10.1016/j.msea.2011.07.049 ↗
98. 98 P. Frint, T. Kaiser, T. Mehner, E. Bruder, M. Scholze, B. Mašek, T. Lampke, and M.F.-X. Wagner: Scientific Reports, 2019, vol. 9, pp. 1-7.10.1038/s41598-019-53303-1 ↗
99. 99 F. Maresca and W.A. Curtin: Acta Materialia, 2017, vol. 134, pp. 302-23.10.1016/j.actamat.2017.05.044 ↗
100. C. Du, R. Petrov, M.G.D. Geers, and J.P.M. Hoefnagels: Mater. Des., 2019, 172, vol. 172.10.1016/j.matdes.2019.107646 ↗