journal article·2016-12

Development of TRIP-Aided Lean Duplex Stainless Steel by Twin-Roll Strip Casting and Its Deformation Mechanism

Yan Zhao, Weina Zhang, Xin Liu, Zhenyu Liu, Guodong Wang

Publisher page

Abstract

In the present work, twin-roll strip casting was carried out to fabricate thin strip of a Mn-N alloyed lean duplex stainless steel with the composition of Fe-19Cr-6Mn-0.4N, in which internal pore defects had been effectively avoided as compared to conventional cast ingots. The solidification structure observed by optical microscope indicated that fine Widmannstatten structure and coarse-equiaxed crystals had been formed in the surface and center, respectively, with no columnar crystal structures through the surface to center of the cast strip. By applying hot rolling and cold rolling, thin sheets with the thickness of 0.5 mm were fabricated from the cast strips, and no edge cracks were formed during the rolling processes. With an annealing treatment at 1323 K (1050 °C) for 5 minutes after cold rolling, the volume fractions of ferrite and austenite were measured to be approximately equal, and the distribution of alloying elements in the strip was further homogenized. The cold-rolled and annealed sheet exhibited an excellent combination of strength and ductility, with the ultimate tensile strength and elongation having been measured to be 1000 MPa and 65 pct, respectively. The microstructural evolution during deformation was investigated by XRD, EBSD, and TEM, indicating that ferrite and austenite had different deformation mechanisms. The deformation of ferrite phase was dominated by dislocation slipping, and the deformation of austenite phase was mainly controlled by martensitic transformation in the sequence of γ→e-martensite→α′-martensite, leading to the improvement of strength and plasticity by the so-called transformation-induced plasticity (TRIP) effect. By contrast, lean duplex stainless steels of Fe-21Cr-6Mn-0.5N and Fe-23Cr-7Mn-0.6N fabricated by twin-roll strip casting did not show TRIP effects and exhibited lower strength and elongation as compared to Fe-19Cr-6Mn-0.4N.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Hydrogen embrittlement and corrosion behaviors in metals · Welding Techniques and Residual Stresses

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (44)

Show source-provided references
1. H. Farnoush, A. Momeni, K. Dehghani, J. Aghazadeh Mohandesi, and H. Keshmiri: Mater. Des., 2010, vol. 43, pp. 220–26.10.1016/j.matdes.2009.06.028 ↗
2. Q. X. Ran, Y. L. Xu, J. Li, J. Q. Wan, X. S. Xiao, H. F. Yu and L. Z. Jiang: Mater. Des., 2014, vol. 56, pp. 959-965.10.1016/j.matdes.2013.12.019 ↗
3. Y. Yang, J. Cao and Y. Gu: Mater. Des., 2015, vol. 83, pp. 820-828.10.1016/j.matdes.2015.05.052 ↗
4. J Wang, P. J. Uggowitzer, R. Magdowski, M.O. Speidel: Scripta Mater., 1999, vol. 40, pp. 123-129.10.1016/S1359-6462(98)00396-0 ↗
5. G. Jha, S. Das, S. Sinha, A. Lodh and A. Haldar: Mater. Sci. Eng. A, 2013, vol. 561, pp. 394-402.10.1016/j.msea.2012.10.047 ↗
6. P. Dvořák and J. Jandova: Hydrometallurgy, 2005, vol. 77, pp. 29-33.10.1016/j.hydromet.2004.10.007 ↗
7. M. Sumita, T. Hanawa and S.H. Teoh: Mater. Sci. Eng. A, 2004, vol. 24, pp. 753-760.10.1016/j.msec.2004.08.030 ↗
8. B. I. Voronenko: Met. Sci. Heat Treat., 1997, vol. 39, pp. 20-29.
9. M. Fujisawa, Y. Kato and T. Ujiro: CAMP-ISIJ, 2009, vol. 22, pp. 1163-1164.
10. M. Fujisawa, Y. Kato and T. Ujiro: CAMP-ISIJ, 2008, vol. 21, pp. 602.
11. J.Y. Choi, J.H. Ji, S.W. Hwang and K.-T. Park: Mater. Sci. Eng. A, 2012, vol. 534, pp. 673-680.10.1016/j.msea.2011.12.025 ↗
12. J.Y. Choi, J.H. Ji, S.W. Hwang and K.-T. Park: Mater. Sci. Eng. A, 2012, vol. 535, pp. 32-39.10.1016/j.msea.2011.12.037 ↗
13. J.Y. Choi, J.H. Ji, S.W. Hwang and K.-T. Park: Mater. Sci. Eng. A, 2011, vol. 528, pp. 6012-6019.10.1016/j.msea.2011.04.038 ↗
14. [14] C. Herrera, D. Ponge and D. Raabe: Acta Mater., 2011, vol. 59, pp. 4653-4664.10.1016/j.actamat.2011.04.011 ↗
15. [15] J. Glownia, B. Kalandyk and K. Hübner: Mater. Charact., 2001, vol. 47, pp. 149-155.10.1016/S1044-5803(01)00163-2 ↗
16. C. A. Santos, J. A. Spim, Jr. and A. Garcia: J. Mater. Process. Technol., 2000, vol. 102, pp. 33-39.10.1016/S0924-0136(00)00448-9 ↗
17. S.H. Wang, Z.Y. Liu, W.N. Zhang, G.D. Wang, J.L. Liu and G.F. Liang: ISIJ, 2009, vol. 49, pp. 1340-1346.10.2355/isijinternational.49.1340 ↗
18. H.T. Liu, Z.Y. Liu, Y.Q. Qiu, G.M. Cao, C.G. Li and G.D. Wang: Mater. Charact., 2009, vol. 60, pp. 79-82.10.1016/j.matchar.2008.06.005 ↗
19. Z.Y. Liu, Z.S. Lin, S.H. Wang, Y.Q. Qiu, X.H. Liu and G.D. Wang: Mater. Charact., 2007, vol. 58, pp. 974-979.10.1016/j.matchar.2006.10.005 ↗
20. J. Talonen, P. Nenonen, G. Pape and H. Hänninen: Metall. Mater. Trans. A, 2005, vol. 36, pp. 421-432.10.1007/s11661-005-0313-y ↗
21. Z.H. Cai, H. Ding, R.D.K. Misra and Z.Y. Ying: Acta Mater., 2015, vol. 84, pp. 229-236.10.1016/j.actamat.2014.10.052 ↗
22. [22] Z.H. Cai, H. Ding, X. Xue, J. Jiang, Q.B. Xin and R.D.K. Misra: Scripta Mater., 2013, vol. 68, pp. 865-868.10.1016/j.scriptamat.2013.02.010 ↗
23. C.G. Lee, S.-J. Kim, T.-H. Lee and S. Lee: Mater. Sci. Eng. A, 2004, vol. 371, pp. 16-23.10.1016/S0921-5093(03)00035-2 ↗
24. [24] H.K. Feichtinger and G. Stein: Mater. Sci. Forum, 1999, vols. 318-320, pp. 261-70.10.4028/www.scientific.net/MSF.318-320.261 ↗
25. Z. Liu, Z. Lin, Y. Qiu, N. Li, X. Liu and G. Wang: ISIJ Inter., 2007, vol. 47, pp. 254-258.10.2355/isijinternational.47.254 ↗
26. Y. Oikawa, S. Tsuge and H. Kajimura: CAMP-ISIJ, 2010, vol. 23, pp. 412.
27. T.-H. Lee, E. Shin, C.-S. Oh, H.-Y. Ha, S.-J. Kim: Acta Mater., 2010, vol. 58, pp. 3173-3186.10.1016/j.actamat.2010.01.056 ↗
28. G.B. Olson and M. Cohen: Metall. Trans. A, 1976, vol. 7, pp. 1897-1904.
29. T.-H. Lee, C.-S. Oh and S.-J. Kim: Scripta Mater., 2008, vol. 58, pp. 110-113.10.1016/j.scriptamat.2007.09.029 ↗
30. W. Zhang and J. Hu: Mater. Charact., 2013, vol. 79, pp. 37-42.10.1016/j.matchar.2013.02.003 ↗
31. S. Martin, C. Ullrich, D. Simek, U. Martin and D.Rafaja: J. Appl. Cryst., 2011, vol. 44, pp. 779-787.10.1107/S0021889811019558 ↗
32. F. Lecroisey and A. Pineau: Metall. Mater. Trans. B, 1972, vol. 3, pp. 391-400.10.1007/BF02642042 ↗
33. W.-S. Lee and C.-F. Lin: Mater. Sci. Eng. A, 2001, vol. 308, pp. 124-135.10.1016/S0921-5093(00)02024-4 ↗
34. X. Wu, N. Tao, Y. Hong, J. Lu and K. Lu: Scripta Mater., 2005, vol. 52, pp. 547-551.10.1016/j.scriptamat.2004.12.004 ↗
35. H. Fujita, and T. Katayama: Mater. Trans. JIM, 1992, vol. 33, pp. 243–52.10.2320/matertrans1989.33.243 ↗
36. [36] R.P. Singh and R.D. Doherty: Metall. Trans. A, 1992, vol. 23, pp. 307-319.10.1007/BF02660873 ↗
37. S.H. Hong and Y.S. Han: Scripta Metall. Mater., 1995, vol. 32, pp. 1489-1494.10.1016/0956-716X(95)00193-Y ↗
38. L. Bracke, L. Kestens and J. Penning: Scripta Mater., 2007, vol. 57, pp. 385-388.10.1016/j.scriptamat.2007.05.003 ↗
39. T. Sawaguchi, I. Nikulin, K. Ogawa, K. Sekido, S. Takamori, T. Maruyama, Y. Chiba, A. Kushibe, Y. Inoue and K. Tsuzaki: Scripta Mater., 2015, vol. 99, pp. 49-52.10.1016/j.scriptamat.2014.11.024 ↗
40. L.E. Murr, K.P. Staudhammer, and S.S. Hecker: Metall. Trans. A, 1982, vol. 13, pp. 627-635.10.1007/BF02644428 ↗
41. G.B. Olson and M. Cohen: Metall. Trans. A, 1975, vol. 6, pp. 791-795.10.1007/BF02672301 ↗
42. K. Pranke, M. Wendler, A. Weidner, S. Guk, A. Weiß, R. Kawalla: J. Alloys Compd., 2015, vol. 648, pp. 783-793.10.1016/j.jallcom.2015.06.205 ↗
43. S. Martin, S. Wolf, U. Martin, L. Krüger and D. Rafaja: Metall. Mater. Trans. A, 2014, vol. 47, pp. 49-58.
44. Z. Guo and L. Li: Mater. Des., 2016, vol. 89, pp. 665-675.10.1016/j.matdes.2015.10.010 ↗