journal article·2012-05

Characterization and Prediction of Flow Behavior in High-Manganese Twinning Induced Plasticity Steels: Part II. Jerky Flow and Instantaneous Strain Rate

A. Saeed-Akbari, A. K. Mishra, J. Mayer, W. Bleck

Publisher page

Abstract

The jerky and smooth flow curves in high-manganese twinning induced plasticity (TWIP) steels were investigated by comparing Fe-Mn-C and Fe-Mn-Al-C systems. The pronounced serrations on the flow curves of Fe-Mn-C TWIP steel, produced during tensile testing at 300 K (27 °C) and 373 K (100 °C), were shown to be the result of localized high-temperature Portevin Le-Chatelier (PLC) bands moving across the gage length throughout the deformation. The speed of the PLC bands and their temperature effects were found to be strongly dependent on the applied strain rate, which was controlled by adjusting the cross-head speed of the tensile testing machine. The localized temperature-dependent stacking fault energy (SFE) variations resulting from the PLC effect and adiabatic heating were analyzed and compared for both slow and fast deformation rates. The instabilities in the measured logarithmic strain values caused by jerky flow could cause the local strain rate to deviate systematically from the targeted (applied) strain rate. These instabilities are better observed by calculating the instantaneous strain rate (ISR) values for each instant of deformation along the entire gage length. Finally, a new type of diagram was developed by plotting the true stress against the ISR values. From the diagram, the onset of different mechanisms, such as deformation twinning, nonpronounced, and pronounced serrations, could be marked precisely.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Powder Metallurgy Techniques and Materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (43)

Show source-provided references
1. S.J. Lee, J. Kim, S.N. Kane, and B.C. De-Cooman: Acta Mater., 2011, vol. 59, pp. 6809–19.10.1016/j.actamat.2011.07.040 ↗
2. M. Koyama, T. Sawaguchi, T. Lee, C.S. Lee, and K. Tsuzaki: Mater. Sci. Eng. A, 2011, vol. 528, pp. 7310–16.10.1016/j.msea.2011.06.011 ↗
3. K. Chung, K. Ahn, D.H. Yoo, K.H. Chung, M.H. Seo, and S.H. Park: Int. J. Plast., 2011, vol. 27, pp. 52–81.10.1016/j.ijplas.2010.03.006 ↗
4. K. Renard, S. Ryelandt, and P.J. Jacques: Mater. Sci. Eng. A, 2010, vol. 527, pp. 2969–77.10.1016/j.msea.2010.01.037 ↗
5. P.D. Zavattieri, V. Savic, L.G. Hector Jr., J.R. Fekete, W. Tong, and Y. Xuan: Int. J. Plast., 2009, vol. 25, pp. 2298–2330.10.1016/j.ijplas.2009.02.008 ↗
6. J. Kim, L. Chen, H. Kim, S.K. Kim, Y. Estrin, and B.C. De-Cooman: Metall. Mater. Trans. A, 2009, vol. 40A, pp. 3147–58.10.1007/s11661-009-9992-0 ↗
7. L. Chen, H. Kim, S.K. Kim, and B.C. De-Cooman: ISIJ Int., 2007, vol. 47, pp. 1804–12.10.2355/isijinternational.47.1804 ↗
8. Y.N. Dastur and W.C. Leslie: Metall. Trans. A, 1981, vol. 12A, pp. 749–59.10.1007/BF02648339 ↗
9. L.J. Cuddy and W.C. Leslie: Acta Metall., 1972, vol. 20, pp. 1157–67.10.1016/0001-6160(72)90164-2 ↗
10. V. Kandarpa and J.W. Spretnak: Trans. TMS-AIME, 1969, vol. 245, pp. 1439–42.
11. P. Hähner, A. Zeigenbein, and H. Neuhäuser: Phil. Mag. A, 2001, vol. 81, pp. 1633–49.10.1080/01418610108214367 ↗
12. P. Hähner: Mater. Sci. Eng. A, 1996, vol. 207, pp. 208–15.10.1016/0921-5093(95)10033-4 ↗
13. P. Hähner: Mater. Sci. Eng. A, 1996, vol. 207, pp. 216–23.10.1016/0921-5093(95)10032-6 ↗
14. A. Ziegenbein, P. Hähner, and H. Neuhäuser: Mater. Sci. Eng. A, 2001, vols. 309-10, pp. 336–39.10.1016/S0921-5093(00)01709-3 ↗
15. G. Lasko, P. Hähner, and S. Schmauder: Modell. Simul. Mater. Sci. Eng., 2005, vol. 13, pp. 645–56.10.1088/0965-0393/13/5/001 ↗
16. S. Bross, P. Hähner, and E.A. Steck: Comput. Mater. Sci., 2003, vol. 26, pp. 46–55.10.1016/S0927-0256(02)00391-9 ↗
17. J. von Appen and R. Dronskowski: Steel. Res. Int., 2011, vol. 82, no. 2, pp. 101–07.10.1002/srin.201000260 ↗
18. V. Gerold and H.P. Karnthaler: Acta Metall., 1989, vol. 37, pp. 2177–83.10.1016/0001-6160(89)90143-0 ↗
19. P. Penning: Acta Metall., 1972, vol. 20, pp. 1169–75.10.1016/0001-6160(72)90165-4 ↗
20. L.P. Kubin and Y. Estrin: Acta Metall., 1985, vol. 33, pp. 397–407.10.1016/0001-6160(85)90082-3 ↗
21. C. Fressengeas, A.J. Beaudoinb, M. Lebyodkin, L.P. Kubin, and Y. Estrin: Mater. Sci. Eng. A, 2005, vols. 400–401, pp. 226–30.10.1016/j.msea.2005.02.073 ↗
22. L.P. Kubin, K. Chinab, and Y. Estrin: Acta Metall., 1988, vol. 36, pp. 2707–18.10.1016/0001-6160(88)90117-4 ↗
23. L.P. Kubin and Y. Estrin: Acta Metall., 1990, vol. 38, pp. 697–708.10.1016/0956-7151(90)90021-8 ↗
24. A.H. Cottrell: Phil. Mag., 1953, vol. 44, p. 829.10.1080/14786440808520347 ↗
25. S. Zhang, P.G. McCormick, and Y. Estrin: Acta Mater., 2001, vol. 49, pp. 1087–94.10.1016/S1359-6454(00)00380-3 ↗
26. Z. Kovács, D. Fátay, K. Nyilas, and J. Lendvai: J. Eng. Mater. Technol., 2002, vol. 124, pp. 23–26.10.1115/1.1420195 ↗
27. R. Zielke, H.A. Crostack, X. Feng, and G. Fischer: Proc. of the Quantitative Infrared Thermography (QIRT) Conf., 2008, Krakow, Poland.
28. S. Rajesh and G. Ananthakrishna: Phys. Rev. E, 2000, vol. 61, pp. 3664–74.10.1103/PhysRevE.61.3664 ↗
29. A. Saeed-Akbari, L. Mosecker, A. Schwedt, and W. Bleck: Metall. Mater. Trans. A, 2012, DOI:10.1007/s11661-011-0993-4, in press10.1007/s11661-011-0993-4 ↗
30. J.A. Venables: Proc. Eur. Conf. on Electron Microscopy, Delft, The Netherlands, 1960, vol. 1, pp. 443–46.
31. J.A. Venables: Phil. Mag., 1961, vol. 6, p. 379.10.1080/14786436108235892 ↗
32. H. Idrissi, K. Renard, D. Schryvers, and P.J. Jacques: Scripta Mater., 2010, vol. 63, pp. 961–64.10.1016/j.scriptamat.2010.07.016 ↗
33. H. Idrissi, K. Renard, L. Ryelandt, D. Schryvers, and P.J. Jacques: Acta Mater., 2010, vol. 58, pp. 2464–76.10.1016/j.actamat.2009.12.032 ↗
34. J. Kim, S.J. Lee, and B.C. De-Cooman: Scripta Mater., 2011, vol. 65, pp. 363–66.10.1016/j.scriptamat.2011.05.014 ↗
35. G. Gottstein: Physical Foundations of Materials Science, Springer-Verlag, Berlin, Germany, 2004.10.1007/978-3-662-09291-0 ↗
36. S. Asgari, E. El-Danaf, S.R. Kalidindi, and R. Doherty: Metall. Mater. Trans. A, 1997, vol. 28A, pp. 1781–94.10.1007/s11661-997-0109-3 ↗
37. S.M. Zhu and J.F. Nie: Scripta Mater., 2004, vol. 50, pp. 51–55.10.1016/j.scriptamat.2003.09.039 ↗
38. W.G. Johnston and D.F. Stein: Acta Metall., 1963, vol. 11, pp. 317–18.10.1016/0001-6160(63)90186-X ↗
39. D. Canadinc, C. Efstathiou, and H. Sehitoglu: Scripta Mater., 2008, vol. 59, pp. 1103–06.10.1016/j.scriptamat.2008.07.027 ↗
40. G.E. Dieter: Mechanical Metallurgy, 3rd ed., McGraw-Hill, Boston, MA, 1986, pp. 184–240.
41. A.S. Hamada: Ph.D. Dissertation, University of Oulu, Oulu, Finland, 2007.
42. A.S. Hamada, L.P. Karjalainen, and M.C. Somani: Mater. Sci. Eng. A, 2007, vol. 467, pp. 114–24.10.1016/j.msea.2007.02.074 ↗
43. I. Gutierrez-Urrutia and D. Raabe: Acta Mater., 2011, vol. 59, pp. 6449–62.10.1016/j.actamat.2011.07.009 ↗