journal article·2009-04Open access

Fracture-Toughness Analysis in Transition-Temperature Region of Three American Petroleum Institute X70 and X80 Pipeline Steels

Sang Yong Shin, Kuk Je Woo, Byoungchul Hwang, Sangho Kim, Sunghak Lee

Abstract

The fracture toughness in the transition-temperature region of three American Petroleum Institute (API) X70 and X80 pipeline steels was analyzed in accordance with the American Society for Testing and Materials (ASTM) E1921-05 standard test method. The elastic-plastic cleavage fracture toughness (K Jc ) was determined by three-point bend tests, using precracked Charpy V-notch (PCVN) specimens; the measured K Jc values were then interpreted by the three-parameter Weibull distribution. The fracture-toughness test results indicated that the master curve and the 98 pct confidence curves explained the variation in the measured fracture toughness well. The reference temperatures obtained from the fracture-toughness test and index temperatures obtained from the Charpy impact test were lowest in the X70 steel rolled in the two-phase region, because this steel had smaller effective grains and the lowest volume fraction of hard phases. In this steel, few hard phases led to a higher resistance to cleavage crack initiation, and the smaller effective grain size led to a higher possibility of crack arrest, thereby resulting in the best overall fracture properties. Measured reference temperatures were then comparatively analyzed with the index temperatures obtained from the Charpy impact test, and the effects of microstructures on these temperatures were discussed.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Fatigue and fracture mechanics · Hydrogen embrittlement and corrosion behaviors in metals · Material Properties and Failure Mechanisms

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (35)

Show source-provided references
1. R. Denys: Pipeline Technology, Elsevier, Amsterdam, 2000, vol. I, pp. 1–116.
2. D.P. Fairchild, M.L. Macia, S.D. Papka, C.W. Petersen, J.H. Stevens, S.T. Barbas, N.V. Bangaru, J.Y. Koo, and M.J. Luton: Proc. Int. Pipe Dreamer’s Conf., M. Toyoda and R. Denys, eds., Scientific Surveys, Ltd., Yokohama, Japan, 2002, pp. 307–21.
3. K.T. Corbett, R.R. Bowen, and C.W. Petersen: Int. J. Offshore Polar Eng., 2004, vol. 14, pp. 75–80.
4. API Recommended Practice 5L3: Recommended Practice for Conducting Drop-Weight Tear Tests on Line Pipe, American Petroleum Institute, API Publishing Service, Washington, DC, 1996, pp. 1–8.
5. G. Mannucci and D. Harris: Fracture Properties of API X100 Gas Pipeline Steels, Final Report, European Commission, Brussels, Belgium, 2002, pp. 1–128.
6. D.J. Horsley: Eng. Fract. Mech., 2003, vol. 70, pp. 547–52.10.1016/S0013-7944(02)00136-4 ↗
7. E. Heier: Drop Weight Tear Testing of High Toughness Pipeline Material-Metallurgical Examination, Fracture Surface Evaluation, DNV Technical Report No. 2003-3333, Det Norske Veritas, Bærum, Norway, 2003.
8. S.-T. Oh, H.-J. Chang, K.H. Oh, and H.N. Han: Met. Mater. Int., 2006, vol. 12, pp. 121–29.10.1007/BF03027467 ↗
9. “ASTM E1820-06 Standard Test Method for Measurement of Fracture Toughness,” Annual Book of ASTM Standards, ASTM, West Conshohocken, PA, 2006, pp. 1–48.
10. “ASTM E1921-05 Standard Test Method for Determination of Reference Temperature for Ferritic Steels in the Transition Range,” Annual Book of ASTM Standards, ASTM, West Conshohocken, PA, 2005, pp. 1–29.
11. I. Tamura, H. Sekine, T. Tanaka, and C. Ouchi: Thermomechanical Processing of High-Strength Low-Alloy Steels, Butterworth & Co., Ltd., London, 1988, pp. 80–100.10.1016/B978-0-408-11034-1.50007-6 ↗
12. I.D. Choi, D.M. Bruce, D.K. Matlock, and J.G. Speer: Met. Mater. Int., 2008, vol. 14, pp. 139–47.10.3365/met.mat.2008.04.139 ↗
13. M. Diaz-Fuentes, A. Iza-Mendia, and I. Gutierrez: Metall. Mater. Trans. A, 2003, vol. 34A, pp. 2505–16.10.1007/s11661-003-0010-7 ↗
14. “ASTM E23-02 Standard Test Method for Notched Bar Impact Testing of Metallic Materials,” Annual Book of ASTM Standards, ASTM, West Conshohocken, PA, 2002, pp. 1–27.
15. W. Oldfield: ASTM Standardization News, ASTM, West Conshohocken, PA, 1975, pp. 24–29.
16. G. Krauss and S.W. Thompson: ISIJ, 1995, vol. 35, pp. 937–45.10.2355/isijinternational.35.937 ↗
17. C.H. Lee, H.K.D.H. Bhadeshia, and H.-C. Lee: Mater. Sci. Eng., A, 2003, vol. A360, pp. 249–57.10.1016/S0921-5093(03)00477-5 ↗
18. L.J. Habraken and M. Economopoulos: Transformation and Hardenability in Steels, Climax Molybdenum Co., Ann Arbor, MI, 1967, pp. 69–108.
19. N.J. Kim: J. Met., 1983, vol. 35, pp. 21–27.
20. J.Y. Koo, M.J. Luton, N.V. Bangaru, R.A. Petkovic, D.P. Fairchild, C.W. Petersen, H. Asahi, T. Hara, Y. Terada, M. Sugiyama, H. Tamehiro, Y. Komizo, S. Okaguchi, M. Hamada, A. Yamamoto, and I. Takeuchi: Proc. 13th Int. Offshore and Polar Eng. Conf., ISOPE, Honolulu, HI, 2003, vol. 4, pp. 10–18.
21. W. Weibull: J. Appl. Mech., 1951, vol. 18, pp. 293–97.10.1115/1.4010337 ↗
22. K. Wallin: Eng. Fract. Mech., 1984, vol. 19, pp. 1085–93.10.1016/0013-7944(84)90153-X ↗
23. T.L. Anderson and D. Stienstra: J. Test. Eval., 1989, vol. 17, pp. 46–53.10.1520/JTE11532J ↗
24. B. Hwang, Y.M. Kim, S. Lee, N.J. Kim, and S.S. Ahn: Metall. Mater. Trans. A, 2005, vol. 36A, pp. 725–39.10.1007/s11661-005-1004-4 ↗
25. Y.M. Kim, S.Y. Shin, H. Lee, B. Hwang, S. Lee, and N.J. Kim: Metall. Mater. Trans. A, 2007, pp. 1731–42.10.1007/s11661-007-9197-3 ↗
26. B. Hwang, S. Lee, Y.M. Kim, N.J. Kim, J.Y. Yoo, and C.S. Woo: Mater. Sci. Eng., A, 2004, vol. A368, pp. 18–27.10.1016/j.msea.2003.09.075 ↗
27. B. Hwang, Y.G. Kim, S. Lee, N.J. Kim, and J.Y. Yoo: Metall. Mater. Trans. A, 2005, vol. 36A, pp. 371–87.10.1007/s11661-005-0309-7 ↗
28. L.J. Xu, S.Z. Wei, J.D. Xing, Y. Li, and L. Rui: Met. Mater. Int., 2006, vol. 12, pp. 371–75.10.1007/BF03027702 ↗
29. D.W. Suh, C.S. Oh, and S.J. Kim: Met. Mater. Int., 2008, vol. 14, pp. 175–83.10.3365/met.mat.2008.06.275 ↗
30. B.L. Bramfitt and J.G. Speer: Metall. Trans. A, 1990, vol. 21A, pp. 817–29.10.1007/BF02656565 ↗
31. J.H. Chen, G.Z. Wang, C. Yan, H. Ma, and L. Zhu: Int. J. Fract., 1997, vol. 83, pp. 105–20.10.1023/A:1007306932437 ↗
32. G.T. Hahn: Metall. Trans. A, 1984, vol. 15A, pp. 947–59.10.1007/BF02644685 ↗
33. C.A.N. Lanzillotto and F.B. Pickering: Met. Sci., 1982, vol. 16, pp. 371–82.10.1016/0036-9748(82)90153-3 ↗
34. K. Wallin, T. Saario, and K. Törrönen: Int. J. Fract., 1987, vol. 32, pp. 201–10.10.1007/BF00018353 ↗
35. S.Y. Shin, B. Hwang, S. Lee, N.J. Kim, and S.S. Ahn: Mater. Sci. Eng., A, 2007, vol. A458, pp. 281–89.10.1016/j.msea.2006.12.097 ↗