journal article·2011-07Open access

A Self-Consistent Approach for Modeling the Flow Behavior of the Alpha and Beta Phases in Ti-6Al-4V

Jeoung Han Kim, S. L. Semiatin, You Hwan Lee, Chong Soo Lee

Abstract

The flow behavior of the α and β phases in Ti-6Al-4V was interpreted in the context of a self-consistent modeling formalism. For this purpose, high-temperature compression tests were conducted at various temperatures for a single-phase α alloy (Ti-7Al-1.5V), a variety of near-β alloys, and the two-phase alloy Ti-6Al-4V, each with an equiaxed microstructure. The flow behavior of the α phase in Ti-6Al-4V was deduced from the experimental results of the single-phase α alloy. The flow behavior of the β phase, which was predicted by using the self-consistent approach and the measured flow behaviors of Ti-6Al-4V and Ti-7Al-1.5V, showed good agreement with direct measurements of the various near-β alloys. From these results, it was shown that the strength of the α phase is approximately three times higher than that of the β phase at temperatures between 1088 K and 1223 K (815 °C and 950 °C). It was also concluded that the relative strain rates in the two phases varies significantly with temperature. The usefulness of the approach was confirmed by comparing the predicted and measured flow stresses for other Ti-6Al-4V and near-α alloys.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Titanium Alloys Microstructure and Properties · Advanced materials and composites · Metallurgy and Material Forming

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (29)

Show source-provided references
1. S. Gourdet and F. Montheillet: Mater. Sci. Eng. A, 2000, vol. 283, pp. 274-88.10.1016/S0921-5093(00)00733-4 ↗
2. A.A. Salem, S.R. Kalidindi, and S.L. Semiatin: Acta Mater., 2005, vol. 53, pp. 3495-502.10.1016/j.actamat.2005.04.014 ↗
3. K. Murali and N. Chandra: Acta Mater., 1995, vol. 43, pp. 1783-90.10.1016/0956-7151(94)00423-F ↗
4. L. Briottet, J.J. Jonas, and F. Montheillet: Acta Mater., 1996, vol. 44, pp. 1665-72.10.1016/1359-6454(95)00257-X ↗
5. J.H. Kim, N.S. Reddy, J.T. Yeom, C.S. Lee and N.-K. Park: Met. Mater. Int., 2009, vol. 15, pp. 427– 37.10.1007/s12540-009-0427-7 ↗
6. D. Deka, D. Joseph, S. Ghosh, and M. Mills: Metall. Mater. Trans. A, 2006, vol. 37A, pp. 1371-88.10.1007/s11661-006-0082-2 ↗
7. R.A. Lebensohn and G.R. Canova: Acta Mater., 1997, vol. 45, pp. 3687-94.10.1016/S1359-6454(97)00067-0 ↗
8. S.L. Semiatin, F. Montheillet, G. Shen, and J.J. Jonas: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 2719-27.10.1007/s11661-002-0394-9 ↗
9. P. Vo, M. Jahazi, S. Yue, and P. Bocher: Mater. Sci. Eng. A, 2007, vol. 447, pp. 99-110.10.1016/j.msea.2006.10.032 ↗
10. H. Oikawa and T. Oomori: Mater. Sci. Eng. A, 1988, vol. 104, pp. 125-30.10.1016/0025-5416(88)90413-2 ↗
11. H. Oikawa: Metallurgy and Technology of Practical Titanium Alloys, Eds. S. Fujishiro, D. Eylon, and T. Kishi, TMS, Warrendale, PA, 1994, pp. 93-100.
12. H. Oikawa, Y. Ishikawa, and M. Seki: Titanium’92 Science and Technology, F.H. Froes and I.L. Caplan, eds., TMS, Warrendale, PA, 1993, pp. 1779.
13. H. Oikawa, K. Nishimura, and M.X. Cui: Scripta Metall., 1985, vol. 19, pp. 825-28.10.1016/0036-9748(85)90200-5 ↗
14. R. Castro and L. Seraphin: Mem. Sci. Rev. Metall., 1966, vol. 63, pp. 1025-58.10.1051/metal/196663121025 ↗
15. R. Hill: J. Mech. Phys. Solids, 1965, vol. 13, pp. 213-22.10.1016/0022-5096(65)90010-4 ↗
16. R. Hill: J. Mech. Phys. Solids, 1967, vol. 15, pp. 79-95.10.1016/0022-5096(67)90018-X ↗
17. P.M. Suquet: J. Mech. Phys. Solids, 1993, vol. 41, pp. 981-1002.10.1016/0022-5096(93)90051-G ↗
18. N.S. Reddy, C.S. Lee, J.H. Kim, and S.L. Semiatin: Mater. Sci. Eng. A, 2006, vol. 434, pp. 218-26.10.1016/j.msea.2006.06.104 ↗
19. S.L. Semiatin and T.R. Bieler: Acta Mater., 2001, vol. 49, pp. 3565-73.10.1016/S1359-6454(01)00236-1 ↗
20. A.A. Salem, S.R. Kalidindi, and R.D. Doherty: Scripta Mater., 2002, vol. 46, pp. 419-23.10.1016/S1359-6462(02)00005-2 ↗
21. S.L. Semiatin and T.R. Bieler: The Second International Conference on Light Materials for Transportation Systems, Eds. N.J. Kim, C.S. Lee, and D. Eylon, Pusan, Korea, 2001, p. 79.
22. J.D. Eshelby: Proc. R. Soc. Lond., 1957, vol. 241, pp. 376-96.10.1098/rspa.1957.0133 ↗
23. D. Dajno and F. Montheillet: Colloque GS-Titane Traitements Thermomécaniques, Université Paris Sud, Paris, France, 1991, p. 67.
24. H.J. McQueen and D.L. Bourell: Formability and Metallurgical Structure, Eds. A.K. Sachdev and J.D. Embury, TMS, Warrendale, PA, 1987, pp. 344-68.
25. I. Weiss and S.L. Semiatin: Mater. Sci. Eng. A, 1998, vol. 243, pp. 46-65.10.1016/S0921-5093(97)00783-1 ↗
26. N.R. Barton and P.R. Dawson: Model. Simul. Mater. Sci. Eng. A, 2001, vol. 9, pp. 433-63.10.1088/0965-0393/9/5/308 ↗
27. J.S. Kim, Y.W. Chang, and C.S. Lee: Metall. Mater. Trans. A, 1998, vol. 29A, pp. 217-26.10.1007/s11661-998-0174-2 ↗
28. J.H. Kim, S.L. Semiatin, and C.S. Lee: Mater. Sci. Eng. A, 2005, vol. 394, pp. 366-75.10.1016/j.msea.2004.11.061 ↗
29. S.L. Semiatin and T.R. Bieler: Metall. Mater. Trans. A, 2001, vol. 32A, pp. 1787-99.10.1007/s11661-001-0155-1 ↗