journal article·2008-07

Friction Stir Processing of Investment-Cast Ti-6Al-4V: Microstructure and Properties

A.L. Pilchak, D.M. Norfleet, M.C. Juhas, J.C. Williams

Publisher page

Abstract

Investment-cast titanium components are becoming increasingly common in the aerospace industry due to the ability to produce large, complex, one-piece components that were previously fabricated by mechanically fastening multiple pieces together. The fabricated components are labor-intensive and the fastener holes are stress concentrators and prime sites for fatigue crack initiation. The castings are typically hot-isostatically-pressed (HIP) to close internal porosity, but have a coarse, fully lamellar structure that has low resistance to fatigue crack initiation. The as-cast + HIP material exhibited 1- to 1.5-mm prior β grains containing a fully lamellar α + β microstructure consistent with slow cooling from above the β transus. Friction stir processing (FSP) was used to locally modify the microstructure on the surface of an investment-cast Ti-6Al-4V plate. Friction stir processing converted the as-cast microstructure to fine (1- to 2-μm) equiaxed α grains. Using micropillars created with a dual-beam focused ion beam device, it was found that the fine-grained equiaxed structure has about a 12 pct higher compressive yield stress. In wrought products, higher strength conditions are more resistant to fatigue crack initiation, while the coarse lamellar microstructure in the base material has better fatigue crack growth resistance. In combination, these two microstructures can increase the fatigue life of titanium alloy castings by increasing the number of cycles prior to crack initiation while retaining the same low-crack growth rates of the colony microstructure in the remainder of the component. In the current study, high-cycle fatigue testing of investment-cast Ti-6Al-4V was performed on four-point bend specimens. Early results show that FSP can increase fatigue strength dramatically.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Welding Techniques Analysis · Titanium Alloys Microstructure and Properties · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (23)

Show source-provided references
1. G. Lütjering and A. Gysler: Titanium Science and Technology, Proc. 5th Int. Conf. on Titanium, Munich, Germany, 1984
2. R.S. Mishra, M.W. Mahoney, S.X. McFadden, N.A. Mara, A.K. Mukherjee: Scripta Mater., 2000, vol. 42, pp. 163–6810.1016/S1359-6462(99)00329-2 ↗
3. K.V. Jata, S.L. Semiatin: Scripta Mater., 2000, vol. 43, pp. 743–4910.1016/S1359-6462(00)00480-2 ↗
4. C.G. Rhodes, M.W. Mahoney, W.H. Bingel, M. Calabrese: Scripta Mater., 2003, vol. 48, pp. 1451–5510.1016/S1359-6462(03)00082-4 ↗
5. J.-Q. Su, T.W. Nelson, R. Mishra, M. Mahoney: Acta Mater., 2003, vol. 51, pp. 713–2910.1016/S1359-6454(02)00449-4 ↗
6. A.P. Reynolds, E. Hood, W. Tang: Scripta Mater., 2005, vol. 52, pp. 491–9410.1016/j.scriptamat.2004.11.009 ↗
7. M.C. Juhas, G.B. Viswanathan, and H.L. Fraser: Proc. Lightweight Alloys for Aerospace Application, K. Jata, E.W. Lee, W. Frazier, and N.J. Kim. eds., TMS, Warrendale, PA, 2001, pp. 209–17
8. A.J. Ramirez, M.C. Juhas: THERMEC’2003, Mater. Sci. Forum, 2003, vols. 426–432, pp. 2999–300410.4028/www.scientific.net/MSF.426-432.2999 ↗
9. R.S. Mishra, Z.Y. Ma: Mater. Sci. Eng., R, 2005, vol. 50, pp. 1–7810.1016/j.mser.2005.07.001 ↗
10. A.L. Pilchak, M.C. Juhas, J.C. Williams: Metall. Mater. Trans. A, 2007, vol. 38A, pp. 401–0810.1007/s11661-006-9061-x ↗
11. A.L. Pilchak, Z.T. Li, J.J. Fisher, A.P. Reynolds, M.C. Juhas, and J.C. Williams: in Friction Stir Welding and Processing IV, R.S. Mishra, M.W. Mahoney, T.J. Lienert, and K.V. Jata, eds., TMS, Warrendale, PA, 2007, pp. 419–27
12. M.D. Uchic, D.M. Dimiduk, J.N. Florando, and W.D. Nix: Materials Research Society Symposium Proceedings, E.P. George et al., eds., Materials Research Society, Pittsburgh, PA, 2003, vol. 753, pp. BB1.4.1-BB1.4.6
13. G. Lutjering and J.C. Williams: Titanium, Springer, New York, NY, 2003, pp. 113–5, 195, 208
14. S. Suresh: Fatigue of Materials, 2nd ed., Cambridge University Press, New York, NY, 1998, p. 30610.1017/CBO9780511806575 ↗
15. J.C. Newman and I.S. Raju: NASA Technical Memorandum 85793, NASA Langley Research Center, Hampton, VA, Apr. 1984
16. J.C. Chesnutt, J.C. Williams: Metall. Mater. Trans. A, 1977, vol. 8, pp. 514–2210.1007/BF02661765 ↗
17. M.D. Uchic et al. Science, 2004, vol. 305 (5686), pp. 986–8910.1126/science.1098993 ↗
18. D.M. Dimiduk, M.D. Uchic, T.A. Parthasarathy: Acta Mater., 2005, vol. 53 (15), pp. 4065–7710.1016/j.actamat.2005.05.023 ↗
19. J.R. Greer, W.D. Nix: Appl. Phys. A: Mater. Sci. Process., 2005, vol. A80 (8), pp. 1625–2910.1007/s00339-005-3204-6 ↗
20. J.R. Greer, W.C. Oliver, W.D. Nix, Acta Mater., 2005, vol. 53 (6), pp. 1821–3010.1016/j.actamat.2004.12.031 ↗
21. C.A. Volkert, E.T. Lilleodden, Phil. Mag., 2006, vol. 86 (33–35), pp. 5567–7910.1080/14786430600567739 ↗
22. D.M. Dimiduk, M.D. Uchic, and T.A. Parthasarathy: WPAFB, Dayton, OH, unpublished work, 2005
23. J.R. Greer, W.D. Nix, Phys. Rev B: Condens. Matter, 2006, 73 (24), pp. 245410/1–245410/610.1103/PhysRevB.73.245410 ↗