Toughness and strength characteristics of Nb-W-Si ternary alloys prepared by Arc melting
Source abstract
Abstract
This article describes the room-temperature and high-temperature mechanical properties and failure modes of series Nb-W-Si alloys—Nb-10W, Nb-10Si, Nb-10Si-5W, Nb-10W-5Si, and Nb-10W-10Si—prepared by arc melting. For the Nb-10W alloy, the microstructure was a monolithic Nb solid solution (Nbss) with a grain size up to a few hundred microns, while the other four alloys consisted of primary Nbss and a eutectic of Nbss/Nb5Si3 (5-3 silicide) as a result of replacing Nb with Si. Among all alloys, the Nb-10W showed the highest fracture toughness of about 15.3 MPa√m1/2 and the lowest 0.2 pct yield compressive strength of 90 MPa at 1670 K. Conversely, the Nb-10Si-10W had the highest 0.2 pct yield strength of about 330 MPa at 1670 K and the lowest fracture toughness of 8.2 MPa√m1/2. It is suggested that toughness is supplied by the metallic Nbss phase, while high-temperature strength is mainly provided by the brittle silicide phase. For the Nb-10W alloy with the monolithic Nbss, intergranular cleavagelike crack propagation is the fracture mode at room temperature, and dislocation movement within the grains and grain-boundary sliding are the dominant modes of high-temperature failure. With two-phase Nbss/Nb5Si3 microstructures, the compressive damage of all four alloys at high temperature was dominated by debonding of the interfaces between the Nbss and the silicide; however, the fracture mode at room temperature is transgranular, controlled by the primary Nbss cleavage.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Intermetallics and Advanced Alloy Properties · Titanium Alloys Microstructure and Properties · High Temperature Alloys and Creep
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (32)
Show source-provided references
1. C. English: Niobium, Proc. Int. Symp., TMS-AIME, Warrendale, PA, 1984, pp. 239–324.
2. M.R. Jackson, B.P. Bewlay, and R.G. Rowe: JOM, 1996, vol. 48, pp. 39–44.10.1007/BF03221361 ↗
3. B.P. Bewlay, J.J. Lewandowski, and M.R. Jackson: JOM, 1997, vol. 49, pp. 44–46 and 67.10.1007/BF02914402 ↗
4. M.G. Mendiratta and D.M. Dimiduk: Metall. Trans. A, 1993, vol. 24A, pp. 501–04.10.1007/BF02657338 ↗
5. M.G. Mendiratta, J.J. Lewandowski, and D.M. Dimiduk: Metall. Trans. A, 1991, vol. 22A, pp. 1573–83.10.1007/BF02667370 ↗
6. P.R. Subramanian, M.G. Mendiratta, and D.M. Dimiduk: JOM, 1996, vol. 48, pp. 33–43.10.1007/BF03221360 ↗
7. J.B. Sha, H. Hirai, T. Tabaru, H. Ueno, A. Kitahara, and S. Hanada: J. Jpn. Inst. Met., 2000, vol. 64, pp. 331–34 (in Japanese).10.2320/jinstmet1952.64.5_331 ↗
8. J.B. Sha, H. Hirai, T. Tabaru, H. Ueno, A. Kitahara, and S. Hanada: Mater. Sci. Eng. A, 2003, vol. 343, pp. 282–9.10.1016/S0921-5093(02)00371-4 ↗
9. J.B. Sha, H. Hirai, T. Tabaru, H. Ueno, A. Kitahara, and S. Hanada: Mater. Trans., JIM, 2000, vol. 41 (9), pp. 1125–28.10.2320/matertrans1989.41.1125 ↗
10. H. Hirai, T. Tabaru, H. Ueno, A. Kitahara, and S. Hanada: J. Jpn. Inst. Met., 2000, vol. 64, pp. 474–80 (in Japanese).10.2320/jinstmet1952.64.6_474 ↗
11. I. Weiss, M. Thirukkonda and R. Srinivasan: MRS Symp. Proc., 1994, vol. 322, pp. 377–86.10.1557/PROC-322-377 ↗
12. P.R. Subramanian, M.G. Mendiratta, D.M. Dimiduk, and M.A. Stucke: Mater. Sci. Eng., 1997, vols. A239–A240, pp. 1–13.10.1016/S0921-5093(97)00555-8 ↗
13. E.S.K. Menon, P.R. Subramanian, and D.M. Dimiduk: Metall. Mater. Trans. A, 1996, vol. 27A, pp. 1647–59.10.1007/BF02649822 ↗
14. W.O. Soboyejo, F.Y.E. Dipasquale, C. Mercer, T.S. Srivatsan, and D.G. Konitzer: Metall. Mater. Trans. A, 1999, vol. 30A, pp. 1025–38.10.1007/s11661-999-0155-0 ↗
15. T. Tabaru and S. Hanada: Intermetallics, 1998, vol. 6, pp. 735–39.10.1016/S0966-9795(98)00052-1 ↗
16. T. Tabaru and S. Hanada: Intermetallics, 1999, vol. 7, pp. 807–19.10.1016/S0966-9795(98)00130-7 ↗
17. Binary Alloy Phase Diagrams, T.B. Massalski, ed., ASM, Materials Park, OH, 1990, vol. 1, pp. 179–81.
18. B.P. Bewlay, M.R. Jackson, and A. Lipsitt: Metall. Mater. Trans. A, 1996, vol. 27A, pp. 3801–08.10.1007/BF02595629 ↗
19. B.V. Cockeram, H.J. Schmutzler, J. Shyue, K. Hoshino, S. Meng, R. Wheeler, and H.L. Fraser: Mater. Res. Soc. Symp. Proc., Materials Research Society, Pittsburgh, PA, 1995.
20. C. Roos, D. Oquab, and B. Pieraggi: Mater. Sci. Forum, 1997, vols. 251–254, pp. 119–26.10.4028/www.scientific.net/MSF.251-254.119 ↗
21. Y.V. Dzyadkevich and L.I. Kytskay: JOM, 1997, vol. 1, pp. 30–31.10.1007/BF02914627 ↗
22. R.A. Perkins and G.H. Meier: JOM, 1990, Aug., pp. 17–21.10.1007/BF03221046 ↗
23. J.D. Rigney and J.J. Lewandowski: Metall. Mater. Trans. A, 1996, vol. 27A, pp. 3293–3306.
24. P.R.V. Evans: Less-Common Met., 1962, vol. 4, pp. 78–91.10.1016/0022-5088(62)90062-0 ↗
25. J.D. Rigney, P.M. Singh, and J.J. Lewandowski: JOM, 1992, vol. 42 (8), pp. 36–41.10.1007/BF03222301 ↗
26. A.V. Samant and J.J. Lewandowski: Metall. Mater. Trans. A, 1997, vol. 28A, pp. 389–99.10.1007/s11661-997-0140-4 ↗
27. M.G. Mendiratta, R. Goetz, D.M. Dimiduk, and J.J. Lewandowski: Metall. Mater. Trans. A, 1995, vol. 26A, pp. 1767–77.10.1007/BF02670764 ↗
28. J. Kajuchi, J. Short, and J.J. Lewandowski: Acta Metall. Mater., 1990, vol. 43 (5), pp. 1955–67.10.1016/0956-7151(94)00391-T ↗
29. J.R. Griffiths and D.R.J. Owen: J. Mech. Phys. Solid, 1997, vol. 9, pp. 419–31.
30. M.F. Ashby, F.J. Blunt, and M. Bannister: Acta Metall. Mater., 1989, vol. 7, pp. 1847–57.10.1016/0001-6160(89)90069-2 ↗
31. J.B. Sha, H. Hirai, T. Tabaru, H. Ueno, A. Kitahara, and S. Hanada: Metall. Mater. Trans. A, 2003, vol. 34A, pp. 85–94.10.1007/s11661-003-0210-1 ↗
32. Quantitative Microscopy, R.T. DeHoff and F.N. Rhines, eds., McGraw-Hill, Inc., New York, NY, 1968, pp. 45–77.