journal article·2017-09

Hydrogen Environment Assisted Cracking of Modern Ultra-High Strength Martensitic Steels

Greger L. Pioszak, Richard P. Gangloff

Publisher page

Abstract

Martensitic steels (Aermet®100, Ferrium®M54™, Ferrium®S53®, and experimental CrNiMoWV at ultra-high yield strength of 1550 to 1725 MPa) similarly resist hydrogen environment assisted cracking (HEAC) in aqueous NaCl. Cracking is transgranular, ascribed to increased steel purity and rare earth addition compared to intergranular HEAC in highly susceptible 300M. Nano-scale precipitates ((Mo,Cr)2C and (W,V)C) reduce H diffusivity and the K-independent Stage II growth rate by 2 to 3 orders of magnitude compared to 300M. However, threshold K TH is similarly low (8 to 15 MPa√m) for each steel at highly cathodic and open circuit potentials. Transgranular HEAC likely occurs along martensite packet and {110}α′-block interfaces, speculatively governed by localized plasticity and H decohesion. Martensitic transformation produces coincident site lattice interfaces; however, a connected random boundary network persists in 3D to negate interface engineering. The modern steels are near-immune to HEAC when mildly cathodically polarized, attributed to minimal crack tip H production and uptake. Neither reduced Co and Ni in M54 and CrNiMoWV nor increased Cr in S53 broadly degrade HEAC resistance compared to baseline AM100. The latter suggests that crack passivity dominates acidification to widen the polarization window for HEAC resistance. Decohesion models predict the applied potential dependencies of K TH and da/dt II with a single-adjustable parameter, affirming the importance of steel purity and trap sensitive H diffusivity.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Hydrogen embrittlement and corrosion behaviors in metals · Microstructure and Mechanical Properties of Steels · High Temperature Alloys and Creep

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (100+)

Show source-provided references
1. R.P. Gangloff: in Compr. Struct. Integr., vol. 6, I. Milne, R.O. Ritichie, B. Karihaloo, J. Petit, and P. Scott, eds., Elsevier Science, New York, 2003, pp. 31–101.10.1016/B0-08-043749-4/06134-6 ↗
2. W.M. Garrison, Jr. and N.R. Moody: in Gaseous Hydrog. Embrittlement Mater. Energy Technol., vol. 1, R.P. Gangloff and B.P. Somerday, eds., Woodhead Publishing Limited, Cambridge, 2012, pp. 421–92.10.1533/9780857093899.3.421 ↗
3. D.P. Dautovich and S. Floreen: in Hydrogen Embrittlement of Iron Based Alloys, R.W. Staehle, J. Hochmann, R.D. McCright, and J.E. Slater, eds., NACE International, Houston, 1973, pp. 798–815.
4. C.J. McMahon: Engr. Fract. Mech., vol. 68, 2001, pp. 773-88.10.1016/S0013-7944(00)00124-7 ↗
5. R.P. Wei: Fracture Mechanics: Integration of Mechanics, Materials Science and Chemistry, Cambridge University Press, New York, NY, 2010.10.1017/CBO9780511806865 ↗
6. R.A. Oriani: Corrosion Journal, vol. 43, 1987, pp. 390-7.10.5006/1.3583875 ↗
7. I.M. Robertson, P. Sofronis, A. Nagao, M.L. Martin, S. Wang, D.W. Gross and K.E. Nygren: Metall. Mater. Trans. A, vol. 46A, 2014, pp. 2323-41.
8. S.P. Lynch: Corros. Rev., vol. 30, 2012, pp. 105-123.10.1515/corrrev-2012-0502 ↗
9. R.P. Gangloff: in Hydrog. Eff. Mater. Behav. Corros. Deform. Interact., N.R. Moody, A.W. Thompson, R.E. Ricker, G.W. Was, and R.H. Jones, eds., The Minerals Metals & Materials Society, Warrendale, PA, 2003, pp. 477–97.
10. R.P. Gangloff: in Materials Performance in Hydrogen Environments, B.P. Somerday and P. Sofronis, eds., ASME, New York, 2017.
11. R.P. Gangloff, H. M. Ha, J.T. Burns, and J.R. Scully: Metall. Mater. Trans. A, vol 45, 2014, pp. 3814-34.10.1007/s11661-014-2324-z ↗
12. W.W. Gerberich: in Gaseous Hydrog. Embrittlement Mater. Energy Technol., vol. 2, R.P. Gangloff and B.P. Somerday, eds., Woodhead Publishing Limited, Cambridge, 2012, pp. 209–46.
13. B.A. Kehler and J.R. Scully: Corrosion Journal, vol. 65, 2008, pp. 465-77.10.5006/1.3278484 ↗
14. E. Martinez-Paneda, C.F. Niordson and R.P. Gangloff: Acta Mater., vol 117, 2016, pp. 321-32.10.1016/j.actamat.2016.07.022 ↗
15. N. Bandyopadhyay, J. Kameda, and C.J. McMahon: Metall. Trans. A, vol. 14, 1983, pp. 881-8.10.1007/BF02644292 ↗
16. C.J. McMahon: Gaseous Hydrog. Embrittlement Mater. Energy Technol., vol. 2, R.P. Gangloff and B.P. Somerday, eds., Woodhead Publishing Limited, Cambridge, 2012, pp. 154–65.
17. G.B. Olson: Acta Mater., vol. 61, 2013, pp. 771-81.10.1016/j.actamat.2012.10.045 ↗
18. C.J. Kuehmann and G.B. Olson: Mater. Sci. Technol., vol. 25, 2009, pp. 472-8.10.1179/174328408X371967 ↗
19. C.E. Campbell and G.B. Olson: J. Comput. Mater. Des., vol. 7, 2001, pp. 145-70.10.1023/A:1011808225838 ↗
20. C.E. Campbell and G.B. Olson: J. Comput. Mater. Des., vol. 7, 2001, pp. 171-94.10.1023/A:1011834720387 ↗
21. G.R. Speich and W.C. Leslie: Metall. Trans., vol. 3, 1972, pp. 1043-54.10.1007/BF02642436 ↗
22. G.R. Speich, D. Dabkowski, and L. Porter: Metall. Trans. A, vol. 4, 1973, pp. 303-15.10.1007/BF02649630 ↗
23. R.O. Ritchie, M.O. Castro Cedeno, V.F. Zackay, and E.F. Parker: Metall. Trans. A, vol. 9, 1978, pp. 35-40.10.1007/BF02647168 ↗
24. Y.H. Kim, H.J. Kim, and J.W. Morris: Metall. Trans. A, vol. 17A, 1986, pp. 1157-64.10.1007/BF02665314 ↗
25. Y. Lee and R.P. Gangloff: Metall. Mater. Trans. A, vol. 38, 2007, pp. 2174-90.10.1007/s11661-006-9051-z ↗
26. D. Figueroa and M.J. Robinson: Corros. Sci., vol. 52, 2010, pp. 1593-1602.10.1016/j.corsci.2010.01.001 ↗
27. R. Ayer and P.M. Machmeier: Metall. Trans. A, vol. 24, 1993, pp. 1943-55.10.1007/BF02666329 ↗
28. R. Padmanabhan: Ph.D. Dissertation, Oregon Graduate Center, Beaverton, OR, 1982.
29. R. Padmanabhan and W.E. Wood: Corrosion, vol. 41, 1985, pp. 688-99.10.5006/1.3583005 ↗
30. R.L.S. Thomas, J.R. Scully, and R.P. Gangloff: Metall. Trans. A, vol. 34, 2003, pp 327-44.10.1007/s11661-003-0334-3 ↗
31. R.L.S. Thomas, D. Li, R.P. Gangloff, and J.R. Scully: Metall. Mater. Trans. A, vol. 33, 2002, pp. 1991-2004.10.1007/s11661-002-0032-6 ↗
32. Processing Information for Ferrium M54, QPI-M54, QuesTek Innovations, Evanston, IL, 2012.
33. H.-J. Jou: US Patent, No. US9051635 B2, 2015.10.1016/S0969-4765(15)30107-7 ↗
34. J. Waldman, W.M. Garrison, Jr., and R.P. Gangloff: Final Report 0032-11/CD002, STTR Topic No. N08-T010, Navmar Applied Sciences Corporation, Warminster, PA, 2011.
35. W.M. Garrison, Jr.: US Patent Application, No. US2013/0228253, 2013.
36. Processing Information for Ferrium S53, QPI-S53, QuesTek Innovations, Evanston, IL, 2013.
37. C.J. Kuehmann, G.B. Olson, and J-J Jou: US Patent, No. US7967927 B2, 2011.
38. C.J. Kuehmann, B.E. Tufts, and P. Trester: Adv. Mater. Process., vol. 166, 2008, pp. 37-40.
39. R.P. Gangloff and A.Turnbull: in Model. Environ. Eff. Crack Initiat. Propag., W.W. Gerberich and R.H. Jones, eds., TMS-AIME, Warrendale, 1986, pp. 55–81.
40. F.G. Wei and K. Tsuzaki: in Gaseous Hydrog. Embrittlement Mater. Energy Technol. vol. 1, R.P. Gangloff and B.P. Somerday, eds., Woodhead Publishing Limited, Cambridge, 2012, pp. 493–525.10.1533/9780857093899.3.493 ↗
41. J. Wright: in Proc. 2010 Stainless Steel Work Am. Conf., Stainless Steel World, Woodlands, Houston, TX, 2010, pp. 1–13.
42. J. Grabowski, C. Kuehmann, J. Sebastian, H.-J. Jou, R. Kooy, and C. Kern: in Proc. 2012 Aircraft Airworth. Sustain. Conf., Baltimore, MD, 2012, pp. 1–23.
43. R.P. Gangloff, Corrosion Journal, vol. 72, 2016, pp, 862-80.10.5006/1920 ↗
44. The Minerals, Metals and Materials Society: Modeling Across Scales: A Roadmapping Study for Connecting Materials Models and Simulations Across Length and Time Scales, The Minerals, Metals and Materials Society, Warrendale, PA, 2015, doi:10.7449/multiscale_1.10.7449/multiscale_1 ↗
45. Y.H. Kim and J.W. Morris Jr.: Metall. Mater. Trans. A, vol. 14, 1983, pp. 1883-8.10.1007/BF02645559 ↗
46. S. Bechtle, M. Kumar, B.P. Somerday, M.E. Launey, and R.O. Ritchie: Acta Mater., vol. 57, 2009, pp. 4148-57.10.1016/j.actamat.2009.05.012 ↗
47. S. Kobayashi, T. Maruyama, S. Tsurekawa, and T. Watanabe: Acta Mater., vol. 60, 2012, pp. 6200-12.10.1016/j.actamat.2012.07.065 ↗
48. G.L. Pioszak: Ph.D. Dissertation, University of Virginia, Charlottesville, VA, 2015.
49. G.L. Pioszak and R.P. Gangloff: Corros. J., 2017. DOI:10.5006/2437.10.5006/2437 ↗
50. R. Chait: Metall. Trans., vol. 3, 1972, pp. 369-75.10.1007/BF02642040 ↗
51. C.H. Yoo, H.M. Lee, J.W. Chan, and J.W. Morris: Metall. Mater. Trans. A, vol. 27, 1996, pp. 3466-72.10.1007/BF02595438 ↗
52. C. Wang, C. Zhang, and Z Yang: Micron, vol. 67, 2014, pp. 112-16.10.1016/j.micron.2014.07.008 ↗
53. F.J. Humphreys: Scripta Mater., vol. 51, 2004, pp. 771-6.10.1016/j.scriptamat.2004.05.016 ↗
54. F.J. Humphreys: J. Mater. Sci., vol. 6, 2001, pp. 3833-54.10.1023/A:1017973432592 ↗
55. D. G. Brandon: Acta Metall., vol. 14, 1966, pp. 1479-84.10.1016/0001-6160(66)90168-4 ↗
56. P. Lejcek: Grain Bound Segregation in Metals, Springer, Prague, 2010, pp. 5–22.10.1007/978-3-642-12505-8_2 ↗
57. E.E. Underwood: Quantitative Stereology, Addison-Wesley, Reading, MA, 1970.
58. E. Charkaluk, M. Bigerelle, and A. Iost: Eng. Fract. Mech., vol. 61, 1998, pp. 119-39.10.1016/S0013-7944(98)00035-6 ↗
59. C.B. Crane and R.P. Gangloff: Corros. J., vol. 72, 2016, pp. 221-41.10.5006/1766 ↗
60. R.P. Gangloff, D.C. Slavik, R.S. Piascik, and R.H. Van Stone: in Small Crack Test Methods, ASTM STP 1149, J. M. Larsen and J. E. Allison, eds., ASTM International, West Conshohocken, PA, 1992, pp 116–68.10.1520/STP15067S ↗
61. J.K. Donald and J. Ruschau: in Fatigue Crack Meas. Tech. Appl., K.J. Marsh, R.A. Smith, and R.O. Ritchie, eds., EMAS, West Midlands, 1991, pp. 11–38.
62. C.C. Kinney, K.R. Pytlewski, A.G. Khachaturyan, and J.W. Morris, Jr.: Acta Mater., vol. 69, 2014, pp. 372-85.10.1016/j.actamat.2014.01.058 ↗
63. S. Morito, H. Tanaka, R. Konishi, T. Furuhara, and T. Maki: Acta Mater., vol. 51, 2003, pp. 1789-99.10.1016/S1359-6454(02)00577-3 ↗
64. S. Morito, X. Huang, T. Furuhara, T. Maki, and N. Hansen: Acta Mater., vol 54, 2006, pp. 5323-31.10.1016/j.actamat.2006.07.009 ↗
65. J.W. Morris: ISIJ International, vol. 51, 2011, pp. 1569-75.10.2355/isijinternational.51.1569 ↗
66. R. Bhambroo, S. Roychowdhury, V. Kain, and V.S. Raju: Matls. Sci. Engr. A, vol. 568, 2013 pp.127-33.10.1016/j.msea.2013.01.011 ↗
67. M. Gao and R.P. Wei: Acta Metall., vol. 32, 1984, pp. 2115-24.10.1016/0001-6160(84)90190-1 ↗
68. A. Shibata, H. Takahashi, and N. Tsuji: ISIJ Intl., vol. 52, 2012, pp. 208-12.10.2355/isijinternational.52.208 ↗
69. A. Nagao, C.D. Smith, M. Dadfarnia, P. Sofronis, and I.M. Robertson: Acta Mater., vol. 60, 2012, pp. 5182-9.10.1016/j.actamat.2012.06.040 ↗
70. A. Nagao, C.D. Smith, M. Dadfarnia, P. Sofronis, and I.M. Robertson: Procedia Mater. Sci., vol. 3, 2014, pp. 1700-5.10.1016/j.mspro.2014.06.274 ↗
71. E.U. Lee, M. Stanley, B. Pregger, C. Lei and E. Lipnickas: Naval Air Warfare Center Aircraft Division, Report No. NAWCADPAX/TIM-2014/292, Patuxent River, MD, 2015.
72. C.J. McMahon: Interface Sci., vol. 12, 2004, pp. 141-6.10.1023/B:INTS.0000028644.07075.4e ↗
73. N. Bandyopadhyay and C.J. McMahon: Metall. Trans. A, vol 14, 1983, pp. 1313-25.10.1007/BF02664814 ↗
74. X.-Y. Liu, J. Kameda, J.W. Anderegg, S. Takaki, K. Abiko, and C.J. McMahon: Mater. Sci. Eng. A, vol. 492, 2008, pp. 218-20.10.1016/j.msea.2008.03.012 ↗
75. Q. Wu and M.A. Zikry: Materials Science and Engineering A, vol. 661, 2016 pp. 32-9.10.1016/j.msea.2016.02.039 ↗
76. Y. Ro, S.R. Agnew, and R.P. Gangloff: Metall. Mater. Trans. A, vol. 39, 2008, pp. 1449-65.10.1007/s11661-008-9522-5 ↗
77. T. Watanabe and S. Tsurekawa: Mater. Sci. Eng. A, vol. 387–389, 2004, pp. 447-55.10.1016/j.msea.2004.01.140 ↗
78. D.H. Lassila and H.K. Birnbaum: Acta Metall., vol. 34, 1986, pp. 1237-43.10.1016/0001-6160(86)90010-6 ↗
79. S. Kobayashi, S. Tsurekawa, T. Watanabe, and G. Palumbo: Scripta Mater., vol. 62, 2010, pp. 294-7.10.1016/j.scriptamat.2009.11.022 ↗
80. C.A. Shuh, R.W. Minich and M. Kumar: Phil. Mag., vol. 83, 2003, pp. 711-26.10.1080/0141861021000056681 ↗
81. M. Fray and C.A. Shuh: Phil. Mag., vol. 85, 2005, pp. 1123-43.10.1080/14786430412331323564 ↗
82. H. Kitahara, R. Ueji, N. Tsuji, and Y. Minamino: Acta Mater., vol. 54, 2006, pp. 1279-88.10.1016/j.actamat.2005.11.001 ↗
83. T. Furuhara, T. Shinyoshi, G. Miyamoto, J. Yamaguchi, N. Sugita, N. Kimura, N. Takemura, and T. Maki: ISIJ Intl., vol. 43, 2003, pp. 2028-37.10.2355/isijinternational.43.2028 ↗
84. C.A. Apple and G. Krauss: Acta Metall., vol. 20, 1972, pp. 849-56.10.1016/0001-6160(72)90077-6 ↗
85. K. Sato: Ph.D. Dissertation, University of California at Berkeley, Berkeley, CA, 2002.
86. P.M. Novotny: in Fundam. Aging Tempering Bainitic Martensitic Steel Prod., TMS-AIME, Warrendale, PA, 1993, pp. 215–36.
87. G. Wang, Y. Yan, J. Li, J. Huang, L. Qiao, and A.A. Volinsky: Matls. Sci. Engr. A, vol. 586, 2013, pp. 142-8.10.1016/j.msea.2013.07.097 ↗
88. J.P. Hirth: Metall. Trans. A, vol. 11, 1980, pp. 861-90.10.1007/BF02654700 ↗
89. G.L. Pioszak, Yongwon Lee, W.M. Garrison, and R.P. Gangloff: Effect of Liquid Nitrogen Chill on SCC of AerMet ® 100 Ultra-High Strength Steel, CorrDefense, NACE International, Houston, TX, 2012. (Available from the authors since https://www.corrdefense.org/External/ViewList.aspx?ListID=999 is incomplete.)
90. J.T. Burns, Z.D. Harris, J.D. Dolph, and R.P. Gangloff: Metall. Mater. Trans. A, vol. 47, 2016, pp. 990-7.10.1007/s11661-015-3315-4 ↗
91. H. Huang and W.W. Gerberich: Acta Metall., vol. 42, 1994, pp. 639-47.10.1016/0956-7151(94)90260-7 ↗
92. J. Weertman, I.-H Lin and R. Thomson, Acta Metall., vol. 42, 1983, pp. 473–82.10.1016/0001-6160(83)90035-4 ↗
93. P. Doig and G.T. Jones: Metall. Trans. A, 1977, vol. 8, pp. 1993–98.10.1007/BF02646573 ↗
94. T.-Y. Zhang and J. E. Hack: Metall. Mater. Trans. A, vol. 30A, 1999, pp. 155-9.10.1007/s11661-999-0203-9 ↗
95. D. Li, R. P. Gangloff, and J. R. Scully: Metall. Trans. A, vol. 35, 2004, pp. 849-64.10.1007/s11661-004-0011-1 ↗
96. W.W. Gerberich, R.A. Oriani, M. J. Lii, X. Chen, and T. Foecke: Philos. Mag. A, vol. 63, 1991, pp. 363-76.10.1080/01418619108204854 ↗
97. J.R. Scully and P.J. Moran: J. Electrochem. Soc., vol. 135, 1988, pp. 1337-48.10.1149/1.2095978 ↗
98. R. A. Oriani: Acta Metall., vol 18, 1970, pp. 147-57.10.1016/0001-6160(70)90078-7 ↗
99. Y.D. Park, I.S. Maroef, A. Landau, and D.L. Olson: Weld. J., pp. 27S–35S, February, 2002.
100. H.J. Grabke and E. Rieche: Mater. Technol., vol. 34, 2000, pp. 331-42.