journal article·2009-03

A Comparison of Columnar-to-Equiaxed Transition Prediction Methods Using Simulation of the Growing Columnar Front

S. McFadden, D.J. Browne, Ch.-A. Gandin

Publisher page

Abstract

In this article, the columnar-to-equiaxed transition (CET) in directionally solidified castings is investigated. Three CET prediction methods from the literature that use a simulation of the growing columnar front are compared to the experimental results, for a range of Al-Si alloys: Al-3 wt pct Si, Al-7 wt pct Si, and Al-11 wt pct Si. The three CET prediction methods are the constrained-to-unconstrained criterion, the critical cooling rate criterion, and the equiaxed index criterion. These methods are termed indirect methods, because no information is required for modeling the equiaxed nucleation and growth; only the columnar solidification is modeled. A two-dimensional (2-D) front-tracking model of columnar growth is used to compare each criterion applied to each alloy. The constrained-to-unconstrained criterion and a peak equiaxed index criterion agree well with each other and some agreement is found with the experimental findings. For the critical cooling rate criterion, a minimum value for the cooling rate (between 0.07 and 0.11 K/s) is found to occur close to the CET position. However, this range of values differs from those cited in the literature (0.15 to 0.16 K/s), leading to a considerable difference in the prediction of the CET positions. A reason for this discrepancy is suggested, based on the fundamental differences in the modeling approaches.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Solidification and crystal growth phenomena · Metallurgy and Material Forming

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (43)

Show source-provided references
1. A.E. Ares, L.M. Gassa, S.F. Gueijman, C.E. Schvezov: J. Cryst. Growth, 2008, vol. 310, pp. 1355–6110.1016/j.jcrysgro.2007.11.169 ↗
2. J.A. Spittle: Int. Mater. Rev., 2006, vol. 51, pp. 247–6910.1179/174328006X102493 ↗
3. J. Hutt, D. StJohn: Int. J. Cast Met. Res., 1998, vol. 11, pp. 13–2210.1080/13640461.1998.11819254 ↗
4. K. Jackson, J. Hunt, D. Uhlmann, T. Seward: Trans. TMS-AIME, 1966, vol. 236, pp. 149–58
5. T.E. Quested, A.L. Greer: Acta Mater., 2005, vol. 53, pp. 4643–5310.1016/j.actamat.2005.06.018 ↗
6. J.D. Hunt: Mater. Sci. Eng., 1984, vol. 65, pp. 75–8310.1016/0025-5416(84)90201-5 ↗
7. M. Gäumann, R. Trivedi, W. Kurz: Mater. Sci. Eng., A, 1997, vols. A226–A228, pp. 763–6910.1016/S0921-5093(97)80081-0 ↗
8. M.A. Martorano, C. Beckermann, C.-A. Gandin: Metall. Mater. Trans. A, 2003, vol. 34A, pp. 1657–7410.1007/s11661-003-0311-x ↗
9. S. McFadden, D.J. Browne, J. Banaszek: Mater. Sci. Forum, 2006, vol. 508, pp. 325–3010.4028/0-87849-991-1.325 ↗
10. C.Y. Wang, C. Beckermann: Metall. Mater. Trans. A, 1994, vol. 25A, pp. 1081–9310.1007/BF02652282 ↗
11. C.-A. Gandin, M. Rappaz: Acta Metall. Mater., 1994, vol. 42, pp. 2233–4610.1016/0956-7151(94)90302-6 ↗
12. M. Wu, A. Ludwig: Metall. Mater. Trans. A, 2007, vol. 38A, pp. 1465–7510.1007/s11661-007-9175-9 ↗
13. G. Guillemot, C.-A Gandin, H. Combeau, R. Heringer: Model. Simul. Mater. Sci. Eng., 2004, vol. 12, pp. 545–5610.1088/0965-0393/12/3/013 ↗
14. S. McFadden and D.J. Browne: Appl. Math. Model., 2009, vol. 33, pp. 1397–41610.1016/j.apm.2008.01.027 ↗
15. D.J. Browne, J.D. Hunt: Numer. Heat Transfer, B-Fund., 2004, vol. 45, pp. 395–41910.1080/10407790490430606 ↗
16. S. McFadden, L. Sturz, H. Jung, N. Mangelinck-Noël, H. Nguyen-Thi, G. Zimmermann, B. Billia, D.J. Browne, D. Voss, D. Jarvis: J. Jpn. Soc. Micrograv. Appl., 2008, vol. 25, pp. 489–94
17. J. Li, J. Wang, G. Yang: J. Cryst. Growth, 2007, vol. 309, pp. 65–6910.1016/j.jcrysgro.2007.08.025 ↗
18. A. Badillo, C. Beckermann: Acta Mater., 2006, vol. 54, pp. 2015–2610.1016/j.actamat.2005.12.025 ↗
19. H.B. Dong, P.D. Lee: Acta Mater., 2005, vol. 53, pp. 659–6810.1016/j.actamat.2004.10.019 ↗
20. C.-A. Gandin: Acta Mater., 2000, vol. 48, pp. 2483–250110.1016/S1359-6454(00)00070-7 ↗
21. S.C. Flood, J.D. Hunt: J. Cryst. Growth, 1987, vol. 82, pp. 543–5110.1016/0022-0248(87)90346-0 ↗
22. S.C. Flood, J.D. Hunt: J. Cryst. Growth, 1987, vol. 82, pp. 552–6010.1016/0022-0248(87)90347-2 ↗
23. C.-A. Gandin: ISIJ Inter., 2000, vol. 40, pp. 971–7910.2355/isijinternational.40.971 ↗
24. A.E. Ares, S.F. Gueijman, R. Caram, C.E. Schvezov: J. Cryst. Growth, 2005, vol. 275, pp. 319–2710.1016/j.jcrysgro.2004.10.115 ↗
25. A.E. Ares, C.E. Schvezov: Metall. Mater. Trans. A, 2007, vol. 38A, pp. 1485–9910.1007/s11661-007-9111-z ↗
26. C.A. Siqueira, N. Cheung, A. Garcia: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 2107–1810.1007/s11661-002-0042-4 ↗
27. C.A. Siqueira, N. Cheung, A. Garcia: J. Alloys Compd., 2003, vol. 351, pp. 126–3410.1016/S0925-8388(02)01026-5 ↗
28. M.D. Peres, C.A. Siqueira, A. Garcia: J. Alloys Compd., 2004, vol. 381, pp. 168–8110.1016/j.jallcom.2004.03.107 ↗
29. M.V. Canté, K.S. Cruz, J.E. Spinelli, N. Cheung, A. Garcia: Mater. Lett., 2007, vol. 61, pp. 2135–3810.1016/j.matlet.2006.08.032 ↗
30. D.J. Browne: ISIJ Int., 2005, vol. 45, pp. 37–4410.2355/isijinternational.45.37 ↗
31. R.D. Doherty, P.D. Cooper, M.H. Bradbury, F.J. Honey: Metall. Trans. A, 1977, vol. 8A, pp. 397–40210.1007/BF02661748 ↗
32. I. Ziv, F. Weinberg: Metall. Trans. B, 1989, vol. 20B, pp. 731–3410.1007/BF02655931 ↗
33. S. McFadden, D.J. Browne: in Proc. 5th Decennial Int. Conf. Solidification Processing, H. Jones, ed., University of Sheffield, Sheffield, United Kingdom, 2007, pp. 172–75
34. S. McFadden, D.J. Browne, J. Banaszek: The John Campbell Symp., M. Tiryakioglu, P.N. Crepeau, eds., TMS, Warrendale, PA, 2005, pp. 365–74
35. J. Banaszek, S. McFadden, D.J. Browne, L. Sturz, G. Zimmermann: Metall. Mater. Trans. A, 2007, vol. 38A, pp. 1476–8410.1007/s11661-007-9140-7 ↗
36. G.F. Franklin, J.D. Powell, A. Emami-Naeini: Feedback Control of Dynamic Systems, 5th ed., Prentice Hall, Upper Saddle River, NJ, 2006, pp. 95–106
37. Y.Z. Sun, G. Cao, S.S. Yao, C. Yu, W.Z. Zhang: J. Shanghai Jiaotong Univ., 2001, vol. 35, pp. 473–76
38. M.B. Djurdjevic, J.H. Sokolowski, W.T. Kierkus, G. Byezynski: Mater. Sci. Forum, 2007, vols. 539–543, pp. 299–30410.4028/0-87849-428-6.299 ↗
39. K.C. Mills: Recommended Values of Thermophysical Properties for Selected Commercial Alloys, ASM INTERNATIONAL, Materials Park, OH, 2002, pp. 37–4910.1533/9781845690144.37 ↗
40. G. Reinhart, N. Mangelinck-Noël, H. Nguyen Thi, T. Schenk, J. Gastaldi, B. Billia, P. Pino, J. Härtwig, J. Baruchel: Mater. Sci. Eng., A, 2005, vols. 413–414, pp. 384–8810.1016/j.msea.2005.08.197 ↗
41. R.H. Mathiesen, L. Arnberg, P. Bleuet, A. Somogyi: Metall. Mater. Trans. A, 2006, vol. 37A, pp. 2515–2510.1007/BF02586224 ↗
42. J. Banaszek, D.J. Browne, P. Furmanski: Arch. Thermodyn., 2003, vol. 24, pp. 37–57
43. G. Guillemot, C.-A. Gandin, H. Combeau: ISIJ Int., 2006, vol. 46, pp. 880–9510.2355/isijinternational.46.880 ↗